Bernini 6-in-1 Torri Fountain User manual

6-In-1 TorrI FounTaIn
Owner’s Manual

PLEASE READ FIRST BEFORE RETURNING
Please call us for assistance at 1+ [phone]
or email us at customercar[email protected]
Our Customer Care Department is available:
Monday - Friday 8:30am to 4:00pm PST, 11:30am to 7:00pm EST
If you have any questions regarding assembly, parts or operation,
please visit our website at www.berninifountains.com. At berninifountains.com
you will nd instructional videos on how to assemble and operate your fountain
and it will keep you up to date on our newest products. You can also
email us with any questions you have.
This product comes with a one year limited warranty against
materials and workmanship.
Please review the list of accessories included with your
Bernini™ Fountain on the next page. Please note, images of
parts are not to scale with one another.
About Torri:
Torri is a medieval village in Italy that sits right next to
the Mediterranean Sea and French border. It has been
described as “a little jewel of popular architecture” and
we hope the Torri Fountain adds a little architectural
jewel to your garden.

Base
Large Bowl
Torri
Topper
Parts to your new
Bernini™Fountain:
Leveling Shim
Battery Compartment,
Water Tube& Water Pump
Dancing Water
Attachments
Innity Bowl/Planter
/Bird Feeder
3 Prong Foot
Cap

CONTENTS
Step 1: Base & Large Bowl
Bowl & Base Locking System
Step 2: Torri Topper Installation
Installing The Torri Topper
Step 3: Battery Installation
Inserting Batteries Into The Battery Compartment
Installing Batteries
Assembly Of Battery Compartment Housing & Battery Cover
Assembly Of Water Pump & Tube To Battery Compartment
Changing Batteries
Step 4: Setting Up Your Fountain
Fill Your Fountain
Operating Your Fountain
Dancing Water Attachments
Table Top Mode
Step 5: 3-in-1 Innity Bowl/Bird Feeder/Planter Bowl
Innity Bowl
How the Self-Watering System Works
Planter
Bird Feeder
Troubleshooting and Maintenance
Cleaning Your Fountain
Cold Storage
Cleaning the Water Pump’s Parts
Water Pump Impeller
Priming the Water Pump
Water Pump Connection
Using Leveling Shims
Troubleshooting Guide
1
2
3
4
5
6
6
7
7
8
9
10
10
11
11
12
13
13
14
15
16
16
16
16
16
17
17
17
18

Remember if you need help contact Customer Care: 1+ [phone] |1
Step 1:
You will need:
Base &
Large Bowl
Base
Large Bowl
Step 1:

Remember if you need help contact Customer Care: 1+ [phone]
2|
At this point, your fountain should look like
the image to the right. Go to the next page
to continue setting up your new Fountain.
Step 3: Turn the Large
Bowl a quarter turn clock-
wise to lock it into place.
Step 2: Align and connect
the Large Bowl to the base.
Note: You will notice that there are two dierent sized
tabs on the bottom of the Large Bowl and there are two
corresponding grooves in the top of the Base. These tabs
t together and lock when turned clockwise.
Bottom of Large Bowl Top of Base
Step 1: Be sure to
place the Base of your
fountain on a at, rm
surface.
Base & Bowl Locking System
A look at how the base & bowl locking system works on your Fountain.
STOP!

Remember if you need help contact Customer Care: 1+ [phone] |3
Step 1:
You will need:
Step 2:
Torri
Topper
Installation
Assembled Base &
Large Bowl
Torri
Topper

Remember if you need help contact Customer Care: 1+ [phone]
4|
Step 1: Like the Large Bowl and Base, the Torri Top-
per uses a key-lock system to connect to the Large
Bowl. The square notches in the groove of the Large
Bowl will align with the square gaps in the bottom of
the Torri Topper.
Step 2: Align and connect the Torri Topper to the
Large Bowl. Turn the Topper a quarter turn clockwise
to lock it into place.
At this point, your fountain should look
like the image on the right. Go to the
next page to continue setup for your new
Fountain.
You can change the look and sound of your
fountain. The Torri Topper is designed to t into
the Large bowl 2 ways, it’s your choice.
OR
Top of Large Bowl Bottom of Topper
Installing The Torri Topper
STOP!

Remember if you need help contact Customer Care: 1+ [phone] |5
Step 1:
You will need:
Step 3:
Fountain
Assembled
Battery
Installation
Battery Compart-
ment,Water Tube
& Water Pump

Remember if you need help contact Customer Care: 1+ [phone]
6|
Figure 1b
Figure 1c
Figure 1a
Battery Compartment Retaining
Screws X2
Installing Batteries:
1. (If Battery Compartment & Water Pump are installed into the Topper) Lift out of the Topper (Figure 1a).
Disconnect the Water Tube from the Battery Compartment (A Figure 3a).
2. Unscrew (counter clockwise) the Battery Compartment Screws, screws DO NOT come out of the battery
compartment, when the screw continues to spin or you hear a click the screw is unscrewed completely, slip
pump cable out of cable notch, and open cover (Figure 1b & 1c). Note: Cover ts tightly, may take some strength
to pull apart
3. Fountain requires 4 D batteries (Not Included), insert x2 D Batteries with the (-, Negative) side facing down
in Battery Compartment (Figure 2a),, negative side of the battery will be resting on the raised coil/spring. Then
insert the other 2x D Batteries with the (+, Positive) side facing down in the Battery Compartment. (Figure 2a).
4. Reinstall the Fountain Top by aligning the locating dowel in the Battery Compartment and Fountain Top. Set
the Battery Cover down onto the Battery Compartment ensuring the dowel sets into the alignment hole and
that the pump wire is placed back in the cable notch. Apply pressure and tighten the Battery Cover Screws by
turning clockwise. NOTE: Pressure must be applied to the Battery Compartment while tightening the screws to
assure the compartment is properly sealed. If needed, while holding battery compartment, place it upside down
on an even surface to tighten screws (Figure 2a, 2b & 2c).
Figure 2a Figure 2b
Locating Dowel
Battery Cover
O-Rings Figure 2c
Inserting Batteries Into The Battery Compartment

Remember if you need help contact Customer Care: 1+ [phone] |7
Figure 3b
Assembly Of Battery Compartment Housing & Cover:
1. Place Battery Cover on Battery Compartment Housing. Turn over assembled Battery unit and
place on a at, level surface. Using a Phillips screwdriver (not included) rst, tighten left screw
down rmly.
2. After tightening the left screw, you will notice a small gap between the Battery Cover and the
Battery Compartment Housing.
3. Using a Phillips screwdriver (not included) tighten the right screw down rmly.
4. After both screws have been tightened, you may notice a small gap between the Battery Cover
and the Battery Compartment Housing.
5. Press down rmly on the bottom of the Battery Compartment Housing to help tighten the gap.
6. Using a Phillips screwdriver re-tighten the screws (left screw rst, right screw second) to
further tighten the gap between the Battery Cover and the Battery Compartment Housing.
1. Take the Battery Compartment
and Water Pump, connect one
side of the Water Tube to the
Water Pump and the other end
to the bottom side of the Battery
Compartment (A & B of Figure
3a).
2. Lower the Battery
Compartment and Water Pump
into the Torri Topper. Battery
Compartment and Water Pump
should be ush with Torri Topper
(Figure 3b).
Figure 3a
Assembly Of Water Pump & Tube To Battery Compartment:

Remember if you need help contact Customer Care: 1+ [phone]
8|
Figure 4b
A
B
1. Remove any Dancing Water Attachment, lift Battery Compartment and Water Pump out
of the Fountain (Figure 4a). Ensure Battery Compartment and Water Pump are completely
dry before opening Battery Compartment. It is important that no water enters the Battery
Compartment.
2. See Installing Batteries Section above on how to reinstall batteries and reassemble.
3. Set the Battery Compartment and Water Pump back into the Fountain (Figure 4d).
Figure 4c
Figure 4d
Figure 4a
Changing Batteries:
STOP!
At this point, your fountain should look like the image on
the left. Go to the next page to continue setting up your
new Fountain.

Remember if you need help contact Customer Care: 1+ [phone] |9
Step 1:
You will need:
Setting
Up Your
Fountain
Step 4:
Fountain
Assembled
Water To
Fill Your
Fountain
Dancing Water
Attachments

Remember if you need help contact Customer Care: 1+ [phone]
10|
After you have picked the container you want your fountain in, ll the container so that the water is
about 1 inch (2.5 centimeters) and/or covers the pump. Next, After you have lled your fountain, to
dislodge any air bubbles from the pump, grab both sides of the large bowl and quickly shake your
fountain for ten seconds. Press the button once to turn your fountain on. Water should be owing
from the top of your fountain. If water is not owing, press the button once more to turn your foun-
tain o and repeat the step above.
2. The B Button allows you to set a daily repeat timer.
. Pressing the button once will turn the fountain on for one hour and then shut o. It will run
again the following day at the same time for an hour and repeat that process daily. The light
will ash once to indicate that a one-hour daily repeat timer has been set (the selection will be
repeated three times).
. Pressing the button twice will turn the fountain on for two hours and then shut o. It will run
again the following day at the same time for two hours and repeat that process daily. The light
will ash twice to indicate that a two-hour daily repeat timer has been set (the selection will be
repeated three times).
. Pressing the button three times will turn the fountain on for three hours and then shut o. It
will run again the following day at the same time for three hours and repeat that process daily.
The light will ash three times to indicate that a three-hour daily repeat timer has been set (the
selection will be repeated three times).
. Pressing the button four times will turn the fountain on for four hours and then shut o. It
will run again the following day at the same time for four hours and repeat that process daily.
The light will ash four times to indicate that a four-hour daily repeat timer has been set (the
selection will be repeated three times).
. Pressing the button a fth time will shut o the fountain. If this is done by mistake and you
want to ensure that a timer is set, press the A button twice to reset the system (which will turn
the fountain on and o), then press the B button as indicated above to set the timer for the
desired interval time.
3. To clear the timer, press the A button twice to reset the system.
The fountain includes
two buttons (A & B) and
an indicator light (C).
1. The A Button turns
the fountain on and
o. When pressed,
the fountain will run
continuously for 6 hours
or until the button is
pressed again, at which
point it will turn o.
Fill Your Fountain
Operating Your Fountain
Figure 1a
A
C
B
Figure 1b
A
C
B

Remember if you need help contact Customer Care: 1+ [phone] |11
DANCING WATER ATTACHMENTS: (OPTIONAL): You can put any of the Dancing Water
Attachments on the Fountain whether the Fountain is running or is not running. Select one of the
Dancing Water Attachments and place on the outlet in the middle of the Battery Compartment
(Figure 2a, 2b & 2c).
NOTE: Please be aware that there is over spray that occurs while using the Dancing Water
Attachments.
Dancing Water Attachments
Table Top Mode
You can now try your Bernini™ Fountain to see if everything is working
correctly! Turn your fountain on and you should see water owing from the
outlet on the top of the Torri Topper. If water is not owing, please refer to
the “Priming The Water Pump” section.
The following section covers any Troubleshooting and Maintenance issues as
needed.
Note: If desired you can set up
your new fountain as a Table
Topper Fountain. Your fountain
Large Bowl and Torri Topper is
fully self contained. Step 1:Twist
the Large Bowl a quarter turn
counter clockwise.
Step 2: Twist the Large Bowl a
quarter turn counter clockwise
and lift large bowl and Torri
Topper o of the base.
Note: Set your fountain base in a safe location for use in the future
when you wish to operate you fountain in full fountain mode.
Step 3: Set your fountain
anywhere you desire, turn on
and enjoy.
Figure 2b Figure 2c
Figure 2a
STOP!

Remember if you need help contact Customer Care: 1+ [phone]
12|
Step 1:
You will need:
Step 5:
3-in-1
Innity Bowl/
Bird Feeder/
Planter Bowl
Innity Bowl/Planter
/Bird Feeder
3 Prong Foot
Cap

Remember if you need help contact Customer Care: 1+ [phone] |13
Innity Bowl
To install the Bowl as an Innity Pool, take the Bowl and the Cap, screw
the Cap into the inside of the bowl turning clockwise (Figure 1, 2 & 3).
Do not over tighten. Place innity Bowl on the fountain spout just as you
would place one of the Dancing Waters Attachments. Push button to
enjoy your fountain.
Figure 1
REMOVEREMOVE INSTALLINSTALL
Figure 2 Figure 3
Figure 4 Figure 5 Figure 6
How the Self-Watering System Works
Your self-watering garden fountain waters from the bottom up. Do not
worry if you do not see the top soil becoming wet after the rst day
or two of use. The bottom layer of the soil will be watered every time
you run the fountain. After approximately 3 days, the soil will reach
its maximum water level. The water will steadily climb to just below
the surface of the soil, while your fountain is on, the water level rises,
watering your plant from bottom to top. (Figure 5).
When your fountain is o, the roots of your plant will be aerated to
produce strong healthy roots. When the fountain is on, the water level
will rise above the surface of the top planter bowl, saturating the soil
(Figure 6).

Remember if you need help contact Customer Care: 1+ [phone]
14|
Planter
To install the Bowl as a Planter, take the Bowl and 3 Prong Foot,
line up the arrows (Figure 11 white circle) on the 3 Prong Foot to
the “Planter” position located on the bottom of the bowl (Figure
8). Align the arrows and push rmly to lock in place. There are 2
small holes on the bottom of the planter that will allow water to be
absorbed from the bottom of the bowl when fountain is running
(Figure 4, 5 & 6). Place the Bowl and Foot on top of the fountain.
Be sure not cover the button or light on top of the fountain. Push
on 3 Prong Foot to secure. Once Planter is in place use your
favorite soil (do not over pack) and plant your new addition to
your family. Push button to enjoy your fountain.
Figure 7
BIRD FEEDER PLANTER
Figure 8

Remember if you need help contact Customer Care: 1+ [phone] |15
Bird Feeder
To install the bird feeder, take the Innity bowl and 3 prong foot,
line up the arrows (Figure 11 white circle) on the 3 prong foot to
the bird feeder position located on the bottom of the bowl (Figure
9 & 10). Align the arrows and push rmly to lock in 3 prong foot.
Place the bowl and foot on top of the fountain. Be sure not cover
the button or light on top of the fountain. Push on 3 prong foot
to secure. Fill bowl with bird food, avoid over-lling to prevent
bird seed from going in your fountain. Push button to enjoy your
fountain.
Figure 11
Figure 9 Figure 10

Remember if you need help contact Customer Care: 1+ [phone]
16|
Troubleshooting and Maintenance
Cleaning Your Fountain
In order to keep your Fountain in tip-top shape and for a prolonged life, it is best if your Fountain and the bowl or
water container that the Fountain is placed in are cleaned periodically. To clean your fountain, drain of all water
and disassemble. Use a mild soap and a soft cloth to clean the parts of your Fountain. DO NOT SCRUB YOUR
FOUNTAIN, AS THIS COULD CAUSE DAMAGE TO THE FINISH OF YOUR BERNINI™ FOUNTAIN.
After about six weeks of usage, you may want to clean the water pump’s impeller to keep your
Bernini™ Fountain in tip-top shape. You will need to drain your fountain of all water prior to clean-
ing the water pumps’ parts.
Cold Storage
Turn power o, remove from container, clean and dry the Fountain of all water. Remove the
batteries for long term storage and bring it indoors. (Now is a great time to clean the pump to
remove any debris that may have accumulated throughout the year).
The impeller inside of the water pump is what pushes water up through your fountain, allowing you
to enjoy the soothing sounds and wonderful sights of your Bernini™ Fountain. After long periods of
usage, this part will need to be cleaned to make sure your fountain runs optimally.
Begin by disconnecting
the pump from the
water tube.
Step 1: Remove the
front of the water pump
by grabbing the sides of
the front panel and pull
it o the unit.
Step 2: Remove the
impeller chamber cover.
This is tightly tted on
to the impeller chamber,
but will come o.
Step 3: Remove the im-
peller from its chamber.
Step 4: Rinse the
impeller until all debris
has been removed.
Then replace the
impeller in the impeller
chamber, put the
impeller chamber back
on and then replace the
pump’s front panel.
Cleaning the Water Pump’s Parts
Water Pump Impeller