Bestway Lay-Z-Spa 54138 User manual

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英封面
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

11
EWater Filter Button
CHydroJet System Button
This button turns the water pump on and off.
The light above the HydroJet system button displays red when activated.
Heat Button
D
Power-Saving Timer Button
G
NOTE: Do not press any buttons on the panel and attach the SPA cover during the chlorinating
progress. You can re-adjust the working duration by pushing the Salt Chlorinator System Button.
NOTE: Test the water regularly and make sure the free chlorine level is between 2-4 ppm.
K
AL
CJ
DI
EH
FG
FSalt Chlorinator System Button
Use this button to turn on the Salt Chlorinator System and set the working duration.
You can set the working duration from 3 hours to 5 hours to 8 hours by pushing the
Salt Chlorinator System Button. After setting the working duration, the Salt Chlorinator
System will start to work automatically.
BK
AL
CJ
DI
EH
FG
HYDROJET PRO HYDROJET
Note: The system will shut off automatically after 1 hour.
Note: Do not dry run the HydroJet System.
NOTE: If the heating system is activated, the filtration system will automatically start.
NOTE: After turning off the heating system, the filtration system will continue to operate.
NOTE: The built-in hard water treatment function works automatically.
This is a newly added function, designed to help avoid wasting power by setting the
time and duration of the heating cycle for the spa.
This way, you can enjoy your spa at the time you desire, without needing to leave the
heater on at all times.
STEP 1: Set the heating duration
1. Press the button unit the LED starts to flash.
2. Press the or button to adjust the heating duration (From 1-48 hours).
3. Press the button again to confirm the heating duration.
STEP 2: Set the number of hours FROM NOW when the heater will activate
1. After setting the heating duration, the LED starts to flash.
2. Press the
or button to adjust the hours until time of activation (From 0-99 hours).
3. Press
button again or simply touch nothing for 10 seconds to confirm the setting.The LED
will light steadily, and the countdown to heater activation will begin.
To modify the timer settings: Press the button and use the or button to adjust.
Cancel the setting: Press the button for 2 seconds.
1. The water flow sensor flag didn’t fall back into
the correct position.
2. The water flow sensors are broken.
1. You forgot to remove the 2 stopper caps from inside
the pool.
2. The filter cartridges are dirty.
3. Activate the filter or heat system and put your hand
in front of the outlet pipe inside the pool to check if
you can feel water. flowing out.
a. If no water flows out the water pump is broken.
b. Water flows out but the alarm appears, the
water flow sensors are broken.
1. The water temperature is lower than 4°C (40°F).
2. If the water temperature is higher than
7°C (44.6°F), the pump’s thermometer is broken.
1. The water temperature is over 50°C (122°F).
2. If the water temperature is lower than
45°C (113°F), the pump’s thermometer is broken.
1. The pump’s thermometer connectors are not
working properly.
2. The pump’s thermometer is broken.
The manual reset thermal cut-out has been tripped.
Not enough salt for sanitizing.
Too much salt has been added or too much water
has evaporated.
The fuse is disconnected.
1. Follow the instructions in operation part to add salt in the water.
2. Contact your local Bestway Aftersales Service Center for instructions.
1. Follow the instructions in operation part to remove the salt.
2. Contact your local Bestway Aftersales Service Center for instructions.
1. Unplug the pump, strike the side of the pump firmly (but not violently), and plug
it back in.
2. Contact your local Bestway Aftersales Service Center for instructions.
1. Remove the two stopper caps before starting the heating system. Refer to the
Assembly section in the User’s Manual.
2. Remove the filter set from inside the pool and push the filter or heat button. If no
alarm appears, clean or change the filter cartridges and re-install the filter set
inside the pool.
3. Contact your local Bestway Aftersales Service Center for instructions.
1. The spa is not designed to operate with water temperatures lower than 4ºC (40°F).
Unplug the pump and only re-start the pump when the water temperature reaches
6°C (43°F).
2. Contact your local Bestway Aftersales Service Center for instructions.
1.
The spa is not designed to operate with water temperatures greater than
40°C (104°F). Unplug the pump and only re-start the pump when the water
temperature reaches 38°C (100°F) or lower.
IMPORTANT: Before you’re-start the pump, push the pump’s reset button.
2. Contact your local Bestway Aftersales Service Center for instructions.
Contact your local Bestway Aftersales Service Center for instructions.
Contact your local Bestway Aftersales Service Center for instructions.
1. Unplug the pump and push the reset button, then plug the pump back in.
2. In case the alarm still remains, check the RESET BUTTON section in manual.
3. Contact your local Bestway Aftersales Service Center for instructions.
Contact your local Bestway Aftersales Service Center for instructions.
Solutions
Causes Reasons
The water flow sensors work
without pressing the filter or heat
button.
After starting or during the
functions of filtering or/and
heating, the water flow sensors
do not detect water flow.
The pump’s
thermometer reads the water
temperature below 4°C (40°F).
The pump’s thermometer reads
the water temperature over
50°C (122°F).
The pump’s
thermometer
connections have issues.
The manual reset thermal
cut-out has a problem.
Low salt alarm.
Hign salt alarm.
104°C (219°F) Fuse fault.
Alarms
The system has detected some water leakage inside
the pump.
Water leakage inside the pump.
Contact your local Bestway Aftersales Service Center for instructions.
The signal line between control panel and power board
is not well connected.
Signal line disconnected.
Lay-Z-Massage System Button (For Hydro-Jet Pro)
IMPORTANT: Do not run the Lay-Z-Massage system when the
cover is attached. Air can accumulate inside the spa and cause
irreparable damage to the cover and bodily harm.
NOTE: Heat and massage system work together to create a warm
massage experience.
Use this button to activate the heating system. When the light above the heat button
is red, the heating system is activated. When the light is green, the water is at the set
temperature and the heating system is at rest.
This button turns the filter pump on and off.
The light above the Water Filter Button displays red when activated.
ITemperature Adjustment Buttons
Celsius/Fahrenheit Toggle
H
Press this button for 2 seconds to active the control panel bottons and the light turns to green.
Press this button for 2 seconds to turn off all currently activated functions.
On/Off Button
K
JPower-Saving Timer LED
Once powered up, the LED displays the current water temperature automatically.
After 72 hours of filtration (without using the power saving timer function), the pump will
hibernate and flash “End” with the current water temperature. When the pump is hibernating
both the heating and water filter functions are disabled. To re-active the pump press
lock/unlock button for 3 seconds.
LED Display
L
NOTE: The water heat rate may change in the below conditions:
·When the outdoor temperature is below 15°C (59°F).
·If the cover is not in position when the heating function is activated.
NOTE: To display the current water temperature, run the filter system for at least a minute. The water
temperature as tested by an external thermometer may vary from the temperature as displayed on the spa
panel due to the differing positions of the measurement devices.
This LED flashing means you are setting the heating duration. The light will be on when the
heating function starts to work.
This LED flashing means you are setting the number of hours FROM NOW when the heater will
activate. When the light is on, the Power-Saving Timer function is set.
The temperature can be displayed in either Celsius or Fahrenheit.
Pressing the Temperature Increase or Decrease buttons will cause the LED to flash. When it is
flashing you can adjust to the desired temperature setting. If you hold these buttons down, the
values will rapidly increase or decrease. The new and desired temperature setting will remain
on the LED display for 3 seconds to confirm the new value.
NOTE: The default temperature is 35°C (95°F).
NOTE:
Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
NOTE: After setting, the screen flashes the current temperature and time alternately.
NOTE: Timer adjustment (amount of time with the heater ON) may be set from 1 to 48 hours; Reservation
time adjustment (the number of hours FROM NOW when the heater will begin to function) may be set from
0 to 99 hours. If the timer is set at 0 hour, it means the Timer function is not set.
Note that the timer is one time per use - the user sets the duration of the heating cycle, and how many hours
from now the heating cycle begins. The timer does NOT repeat until reset.
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815
The pump has a 5-minute auto-lock. The LED light will dim out when the pump
is locked (no function is activated).To lock or unlock the pump, place a finger
over the lock/unlock button for 3 seconds.
Use this button to activate the massage system, which has a 30-minute
auto-shutoff feature.
The light above the Lay-Z-Massage system button displays red when activated.
Lock/Unlock Button
A
B

NOTE: Your spa will require additional air to be added from time to time. Changes in temperature from day to night will change the
pressure in the spa and may cause a certain amount of deflation. Please follow the Assembly instructions and drain the spa before
inflating to the accurate pressure needed.
CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean, check and clean your filter cartridges every day-follow
the steps below.
NOTE: We recommend changing your filter cartridges every week. If the filter cartridges remain soiled and discolored they should be replaced.
Water Maintenance
To keep your SPA water clean, chemical balance is necessary. Merely cleaning the filter cartridge is not sufficient for this purpose. Please refer to either of below recommendations:
1. Use the built-in Salt Chlorinator System regularly. The salty water is passed through the chlorinator’s electrolytic cell to produce chlorine which is dissolved instantly in the water. The chlorine
immediately starts to destroy bacteria, algae and oxidize other organic materials.
The first time you use it, we suggest you set the operation time at 8 hours with fresh water and use a test strip to make sure the Free Chlorine is between 2-4ppm. Increase the operation time if
the water temperature is high or if the SPA is uncovered, use the Chlorinator System every 24 hours if the SPA is in use, the operation time depends on the test results and how often you use
the SPA.
NOTE: Test the Free Chlorine concentration twice a day when you first use the Chlorinator System. When the Free Chlorine concentration becomes stable, test once a week to make sure the
Free Chlorine is between 2-4 ppm.
NOTE: Do not use the SPA when the Free Clorine concentration is higher than 4 ppm.
2. Use pool chemicals to maintain water chemistry-dispense chlorine or bromine tablets (do not use granules) with the chemical floater.
MAINTENANCE
pH Total Alkalinity Free Chlorine
7.4-7.6 80-120 ppm 2-4 ppm
NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be handled with care. There are serious health risks from
chemical vapors and the incorrect labeling and storage of chemical containers. Please consult your local pool supply retailer for more information about chemical maintenance. Pay close attention
to the chemical manufacturer's instructions. Spa damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the warranty.
Filter Set Filter Cartridge 58323
Using chemical tablets (not included)
( Reference: Trichlorinafed isocyanuric acid 3-6g )
Using chemical liquid (not included)
(Refer to the instructions of the liquid chemicals purchased)
The water should be changed about every 3 days or longer with proper chemical maintenance. Water quality is influenced by frequency of use, persons using the spa
and general maintenance.
NOTE: We recommend you take a shower before using your Lay-Z-Spa. Cosmetic products, lotions, and other residues on the skin can quickly degrade water quality.
NOTE: Remove the chemical floater from the spa when the spa is in use
IMPORTANT: After performing chemical maintenance and before using the spa, use a test kit (not included) to test the water chemistry.
We recommend maintaining your water as per the table below.
Jet Nozzle Maintenance
1. Twist untill hearing a “click” sound, and pull out the Jet Nozzle to
clean the debris.
2. Insert and twist clockwise to put it back.
Salt Chlorinator System Maintenance
Draining the Spa
NOTE:
Drawings for illustration purposes only. May not reflect actual product. Not to scale.
NOTE: If the deposits remain after washing, place the electrolytic cell in a container, pour kitchen grade vinegar into the container to soak the
titanium plate for about 4 hours and then wash again.
Repeat the operation if necessary.
12
1.
4.
3.
2.
(not included)
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

2. 3. 4.1.
6. 8.
9.
5.
10.
NOTE: Dry the SPA pool
(only for Hydro-Jet Pro)
NOTE: Lift up the spa when
there is only a little water left.
Damages to the handles are
not covered under the warranty.
11. NOTE: Dry the SPA pump
(only for Hydro-Jet Pro)
2.
13
7. NOTE: Dry the water pipe.
NOTE: DO NOT use hard brushes or abrasive cleaners.
Detergent residues and dissolved solids from bathing suits and chemicals may build up on the spa walls. Use soap and water to
clean the walls and rinse thoroughly.
Spa Repair
For Spa inflatable cover
If the spa is torn or punctured, use the provided
heavy-duty repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 minutes before inflation.
Cleaning the spa
For Spa Liner
If the spa is torn or punctured, use the provided PVC repair patch and glue (not
included) following these steps:
1. Clean and dry the area to be repaired.
2. Cut the provided PVC patch to appropriate size.
3.
Use glue (not included) to coat the one side of the newly cut patch. Make sure the
glue is evenly distributed.
4. Wait for 30 seconds and then place the cut patch with glue over the damaged area.
5. Smooth out any bubbles of air that may be trapped underneath, and press firmly
for two minutes.
6. Wait 30 minutes before inflation.
7. The product is once again ready for use. Repeat this process should further leaks
occur.
Lay-Z-Spa Storage
Before storing, make sure the spa and pump are completely dry. This is essential to extend the life of the spa. We recommend using the pump
to blow dry the spa, pump and pipes. Remove the filter sets and discard the used filt er cartridges. Re-attach the two stopper caps onto the spa’s
inlet and outlet valves. It is recommend ed you store the spa in its original package in a warm dry place.
NOTE: Plastic becomes brittle and susceptible to breaking when exposed to subzero temperatures. Freezing can
severely damage the spa. Improper winterization of your spa can void your warranty.
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815

14
TROUBLESHOOTING Bestway strives to provide the most trouble-free spas on the market. If you
experience any problems whatsoever, do not hesitate to contact Bestway or your authorized dealer.
Here are some helpful tips to help you to diagnose and rectify some common sources of trouble.
Problems
Pump does not operate
Pump does not heat properly
Lay-Z-Massage System
does not work
Pump adapters are not level with
the spa adapters
Spa pool leakage
Water is not clean
Probable Causes
- Spa is torn or punctured
- Air valve is loose
Solutions
- Check power source
- Contact your local Bestway Aftersales Service
Center for instructions
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Power failure
- Power circuits broken
- Temperature set too low
- Dirty filter cartridge
- The thermal cut-out cuts off
- The heating element has failed
- Air Pump is overheating
- The Lay-Z-Spa Massage
stops automatically
- Air pump is broken
- One characteristic of PVC is that it
changes shape, which is normal
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
- Sanitary system is not
working
- The titanium plate was coated
- Not enough sanitizing time
- Set the heating system to a higher temperature
(refer to Pump Operation section)
- Clean/replace the Filter Cartridge
(refer to Filter Cartridge Cleaning and Replacement section)
- Press the Reset button on the pump
(refer to Pump Operation section)
- Contact your local Bestway Aftersales Service Center for instructions
- Unplug the pump and wait two hours until the pump has cooled. Insert
the plug and press the Lay-Z-Massage system button
- Press the Lay-Z-Massage system button to reactivate
- Contact your local Bestway Aftersales Service Center for instructions
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge
Cleaning and Replacement section)
- Refer to the chemical manufacturer’s instructions
- Check the power supply or contact your local Bestway Aftersales Service
Center for instructions
- Clean the titanium plate (refer to Salt Chlorinator System
Maintenance section)
PRCD test failed There is a defect in your spa Contact your local Bestway Aftersales Service Center and return the SPA
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if so, use
the provided wrench to fasten the air-valve following these steps:
1. Deflate the SPA.
2. With one hand, hold the backside of the air valve from the inner side of
the spa wall and turn the wrench clockwise.
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815
HydroJet System does not work
Control panel not working
- Unplug the pump and wait for two hours until the pump
has cooled. Plug in and try again
- Contact your local Bestway Aftersales Service Center for instructions
- Water pump is overheating
- Water pump is broken
- To unlock the control panel, press the button for 3 seconds
If the control panel will not unlock, restart the pump – unplug and plug
in the pump.
- Press the on/off button for 2 seconds
If the problem persists, please contact your local Bestway Aftersales
Service Center for instructions.
- The control panel has an
auto-lock, which is activated after 5
minutes of inactivity. The LED
display has one icon: If the
lock icon is highlighted, the control
panel is locked
- Control panel is not activated
What kind of chemicals should be
used for water maintenance? Please consult your local chemical supplier for information about chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions.
Water leaks from the adapters
between the pump and spa
Insert the three stopper caps on to the spa’s ports to prevent water from escaping and disconnect the pump.
Check and make sure the seals are placed correctly inside the pump adapters. If the seals are missing
or not installed correctly, please contact your local Bestway Aftersales Service Center for instructions. If the
seals are correctly in place, reconnect the pump to the spa and hand-tighten the adapters.

15
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815
The product you have purchased comes with a limited warranty. Bestway
®
stands behind our quality guarantee and assures, through a replacement
warranty, your product will be free from manufacturer’s defects.
To enact a warranty claim, this form must be completed and submitted with a copy of your receipt/purchase to your local Bestway After Sales
Center. Please contact your local Bestway After Sales Center before sending any document. They will provide full instructions of what is needed for
your claim. Bestway
®
will not replace any products deemed to have been damaged due to negligence or having been used outside of the owner’s
manual guidelines.
Bestway’s warranty covers manufacturing defects discovered while unpacking the product or during use as recommended within the user manual.
This warranty applies only to product which have not been modified by any 3
rd
parties. The product must be stored and handled in accordance with
the technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but not limited to collision, fire, use of incorrect voltage,
excessive heat exposure, improper installation, improper wiring or testing, improper storage.
Replacements and repairs don’t extend the duration of the warranty. The warranty start date is the date of sale shown on the original
receipt/purchase invoice.
Please choose your Spa
Spa Pump Item Code:
FAX/E-MAIL/TEL: Please refer to your country according to the information found on the back cover or on
www.bestwaycorp.com
Please provide your address details in full. Note: Incomplete address details will result in delayed shipments.
Bestway reserves the right to charge for redelivery of undelivered packages where the recipient is at fault.
Date of purchase:
TO: Bestway®Service Department
Customer Code Number:Date:
Heating System not workingSpa leakage Water Filtration System not working
Lay-Z-Massage System not working
Missing part - Please use the code for the missing part. This
can be found in the owner'smanual.
Control panel shows a failure which cannot be solved
Pump leakage Adapter leakage
Other (Please describe)
REQUIRED INFORMATION - PLEASE WRITE THE SHIPPING ADDRESS
Spa Pump Batch Number:
Name: Address:
Zip Code:
Country:
All drawings for illustration purpose only. Not to scale.
City:
Mobile: Telephone:
Fax:
Retailer:
FOR FAQ, MANUALS, VIDEOS OR SPARE PARTS, PLEASE VISIT OUR WEBSITE: www.bestwaycorp.com.
VIDEOS ARE ALSO AVAILABLE ON OUR BESTWAY CHANNEL ON YOU TUBE: www.youtube.com/user/BestwayService
E-mail:
Spa Pool Batch Number:
Problem description
Limited BESTWAY®Manufacturer’s Warranty
IMPORTANT: ONLY THE DAMAGED PART WILL BE REPLACED, NOT THE COMPLETE SET.
Bestway reserves the right to request photographic evidence of defective parts, or to require sending the
item for additional testing.
In order to best assist you, we request all information you provide to be complete.
Batch Number
Item Code Batch Number
BWSHE.....X
YYYY-MM-DD
BWSHEXXXXXX
YYYY-MM-DD
Close
Open
MODEL NO. #XXXXX
Palm Springs Hawaii

16
S-S-004815/21x28.5cm/54138AU, 54144AU 澳规SPA说明书/JS-YF-2016-B-06737/英
S-S-004815