Bestway FALCON HJ1007 User manual

1
POOL FLOOR CLEANER
FALCON HJ1007
USER MANUAL
Subject to update by manufacturer without prior notice

2
Important Precautions
1. This model applies to swimming pool with flat floor.
2. Do not power on the unit when it is outside of the water.
3. Make sure the power cord is connected to a leakage protective device and appropriate
earthed socket.
4. Do not operate the cleaner when there is people in pool.
5. Do not try to move the floaters along the electric cable. Leave them always in the original
positions.
6. Before power on, make sure the cable is fully released to avoid any winding, which could
affect the cleaner’s performance or cause damage.
7. The filter tray should be cleaned after use. This will prevent the dirty filter tray affecting the
normal operation of the cleaner.
8. The cleaner should be stored in a cool and ventilated place, away from direct sunlight.
9. The power supply unit should be placed in a shaded area. In order to avoid overheating and
the potential damage of components, never cover the power supply unit.
10. Only authorized personnel should open the cleaner’s motor assembly and power supply unit,
fail to do which will cause a invalid warranty.
11. In order to avoid any accident/damage, the power supply unit should be steadily placed at a
minimum distance of 3.5m from the pool edge.
12. Do not use the cleaner beyond the working environment/conditions stated in this manual.
Read this manual carefully before use.
13. Do not uncover the button film on the power supply unit.
14. Close the filtering system of your pool when use this cleaner.
15. Slightly water pollution may occur in case grease in motor seal oil leaks.
16. This model only applies to small pools that corresponding to cleaner’s cable length, there is
risk for the cleaner to work in a too big pool to cause pulling the cleaner upside down by the
limited cable.

3
17. Make sure the power unit be properly positioned for the cleaner to cover as large as pool
surface and in the meantime cleaner has surplus cable once touching the pool end.
Note
1. Putting into or lifting out from pool with the cleaner bottom toward the wall to avoid any possible
scratch to the pool surface.
2. Install the brush before use to avoid possible dirt leaks.

4
Contents
Ⅰ. Introduction································································································P. 5
Ⅱ. Safety········································································································P. 5
Ⅲ. Specifications·····························································································P. 5
Ⅳ. Cleaner Structure························································································P.6
Ⅴ. Operation Instructions·················································································P. 7
Ⅵ. Trouble Shooting·························································································P. 20
Ⅶ. Packing List································································································P. 21
Ⅷ. Packing List································································································P. 21

5
Ⅰ. Introduction:
The automatic swimming pool floor cleaner HJ1007 is a new type of highly efficient swimming pool
cleaning equipment. Through its advanced computer controlled program, it can clean the pool floor
automatically without draining pool water. At the same time, it filters the pool water and gets rid of
suspended particles and sediments.
For safe operation, the cleaner works on DC 24V.
Please read this instruction manual carefully before use.
Ⅱ. Safety:
1, Position requirement of power supply unit：Refer to item 9 and 11 in “Important Precautions”.
2, Requirement of power: Refer to item 3 in “Important Precautions”.
Make sure the cleaner corresponds to your local voltage and frequency (hertz).
Ⅲ. Specifications:
1. Rated input voltage and frequency: 220V/50Hz, 110V/60Hz
2. Output Voltage: DC24V
3. Nominal output power: 150W
4. Working cycle: 1h/1.5h/2h
5. Cable length: 12m (39.37ft)
6. Maximum cleaning area: 60m²(for 12m cable in rectangle pool)
7. Filtering capacity: 20m³/h
8. Filter density: 180/600µm (600µm for the beginning of season)
9. Water temperature of use(for cleaner): 10°C - 35°C / 50°F - 95°F
10. Creeping speed: 20m/min
11. IP Grade：Cleaner-IPX8 Power supply unit-IPX5
12. Working environment temperature(for power unit): 10°C - 40°C / 50°F - 104°F
13. Maximum pool depth: 2m
14. Climb slope: Maximum25°

6
Ⅳ. Cleaner Structure
Assembly the cleaner according to above structure
Top Cover
Filter Tray
Chassis

7
Ⅴ. Operation Instruction
5.1 Cable connection
5.1.1 Plug the cable line into the socket on the power supply unit (note: make sure to plug it in the
correct direction and position), and fasten the nuts on both sides of the plug.
Fig 5-1
5.1.2 Plug into power.
Fig 5-2
Please plug or unplug the
cable by holding this
position

8
5.2 Operational panel
Fig. 5-3
Buttons & indicator lights instructions:
Item
Name
Function
Detail
1
ON / OFF
Power on or off
Power on or off
2
CYCLE
Stop after 1 hour working,
Moving direction reverses every
18 seconds, for small swimming
pool below:
2
1
3

9
Stop after 1.5 hour working,
Moving direction reverses every
23seconds, for medium
swimming pool below:
Stop after 2 hour working,
Moving direction reverses every
28 seconds, for large swimming
pool below:
3
INDICATOR
Flash on corresponding cycle,
all indicators flash after one
cycle finish.

10
5.3 Function and adjustment of nozzle
There are two nozzles on the cleaner, one of them opens once the other closes. Water flows out
through the opening nozzle to thrust the cleaner move forward. Adjust the nozzle by rotating it to
control the moving path.
F. 5-4
5.3.1 Settings of nozzle
Nozzle angle from 0°to 60°
Cleaner moves in approximately straight line when nozzles in position 0°.
Cleaner moves in curved line when angle is set from 0°to 60°.
Note: A full coverage is not guaranteed for some of free shape pools.
5.3.2 Recommended cycle and nozzle settings:
Setting 1 (Default Setting), 0°/ 60°, for most pools.
Nozzle

11
Moving
path
Setting 2: 0°/45°, choose this setting if the cable tangles according to setting 1.
Nozzle
Moving
path

12
Setting 3: 0°/ 30°, choose this setting in case cable tangling STILL occurs under Setting 2.
Nozzle
Moving
path
Setting 4：15°/ 60°, in case the default setting 1 does not cover the pool perfectly.
Nozzle

13
Moving
path
Setting 5：30°/ 60°, this settling enables the cleaner to have better coverage ratio that setting
4.
Nozzle
Moving
path

14
Setting 6: 30°/ 30°，For round pool
Nozzle
Moving
path
Note: Above are recommended settings, different setting may applies to specific pools. Or,
chose bellow settings may lead to a larger coverage.
5.4 Methods of putting the cleaner into pool
Hold a proper position of the cable by one hand ( be sure that the cable from hand to cleaner will
let the cleaner immerge into water but above the floor), hold the cleaner handle by the other hand
to put the cleaner into water slowly.
F.5-5

15
Keep holding the cable before the cleaner Release the rest of the cable after the
filled with water and sinks into pool floor. cleaner falls onto the pool floor slowly
F 5-6
It’ll avoid any turning upside down of the cleaner by following above methods.
F 5-7
5.5 Clean the filter tray
5.5.1 Open the cleaner from both side of the machine ( Fig 5-8,and Fig 5-9)
.
Fig. 5-8 Fig. 5-9

16
5.5.2 Take off the filter tray (Fig. 5-10)
Fig. 5-10
5.5.3 Clean the filter tray (Fig. 5-11, 5-12)
Fig. 5-11 Fig. 5-12

17
5.5.4 Wash the filter tray and chassis then reassemble the cleaner ( Fig. 5-13)
F 5-13
5.5.5 Push both sides of the clips on (Fig 5-14)
F 5-14

18
5.6 Filter net replacement
F 5-15
5.8 Helpful tips
i. Unplug power connection immediately after use (Do not do it with wet hand or naked
foot).
ii. The cleaner should not touch pool walls while lifting out to avoid scratching the pool
surface or any damage to the cleaner.
iii. Before lifting out from pool and placing on the pool edge, suspend the cleaner above
water surface for 10-15 seconds to release the water left inside the cleaner body.
iv. Please hold the cleaner handle to lift it out from pool and never pull the cable.
v. Use 600um filter at the beginning of season to reduce possibility of jet block.
Press buckle to
disassemble
Replace and press to
assemble

19
VI. Trouble Shooting
Symptom
Possible reason
Corrective action
Cable twists or coils
up
Cable not fully released
Unplug power line and release cable
Nozzle in extra angle
Adjust water outlet into proper angle
Obstruction in pool
Remove obstruction in pool
Stuck on main drain outlet of
the pool
Turn off pool filter system
Long time working
Release manualy
Cleaner does not
reach all pool area
Power supply unit
improperly positioned
Place power supply in proper position so
that cleaner can reach all area
Nozzle in improper direction
Adjust nozzle into proper direction
Customized pool shape
Adjust the nozzle to lead to bigger moving
radius
Pool filter system and pump
open
Turn off pool filter system
Cable not long enough in
pool
Release cable
Cleaner does not
work
Power cord not connected
well
Plug power cord and cable line
Damaged during
transportation
Contact local vendor
Cleaner does not match
local rated voltage
Contact local vendor
Move along with pool
sides
Improper nozzle setting
Try to adjust nozzle position

20
Ⅶ. Packing List
Item
Name
Quantity (pc)
Remarks
1
Cleaner
1
In carton
2
Power supply unit
1
In carton
3
Manual& certificate
1
4
Brush
1
5
Filter-180μm
1
In carton
6
Filter-600μm
1
On cleaner
Ⅷ. Warranty
This product has passed all quality control and safety tests, conducted by the technical department of
the factory.
Warranty information:
1. Warranty period is 2 years.
2. This warranty is void if the product has been altered, misused, or has been repaired by
unauthorized personnel.
3. The warranty extends only to manufacturing defects and does not cover any damage resulting
from mishandling of the product by the owner
4. The sales invoice must be presented for any claim or repair during the warranty period.
Please contact your local dealer for any warranty issues.