Better Air BIODIFY User manual

www.BetterAirUS.com
QUICK START GUIDE
BIODIFY™
Biodify™ nourishes your indoor
environment with a repetitive
flow of Enviro-Biotics™. An
environment rich in beneficial
bacteria supports your well
being and cleans air, surfaces
and objects, especially in those
hard to reach areas.
WELCOME TO THE WORLD
OF BETTER AIR
Equipment and
Accessories
A- Biodify™
B- Cartridge
Dimensions: 
3.9in (h) x 9.8in (L) x 2.1in (w)
Weight: 1.4 lb
Power Supply:
    • Input Voltage: 110/230 VAC
    • Output Voltage: 2.4 VDC
Approvals: CE
Working Temp: 35-109 F°
Working Humidity: 85% or less
LIquid Capacity: 3.8 oz cartridges
Performance: Up to 800 sqf
Contact Us
844.44.PROBIO
[e-mail]
www.BetterAirUS.com
© 2015 Better Air North America LLC
All rights reserved
WARNING:
KEEP OUT OF REACH OF
CHILDREN AVOID SWALLOWING
AND EYE CONTACT.
IF SWALLOWED - drink 1-2
glasses of water
EYES - Flush with water
C- Power Block
D- Wall Mount
Biodify™Safety Precautions
• Always unplug the unit before moving it.
• The Biodify™ Enviro-Biotics™ cartridge
should not be refilled with any liquid
other than BetterAir's Enviro-Biotics™
Cartridge supplied by the manufacturer.
The use of any other liquid will forfeit the
warranty.
• Do not immerse in or place the Biodify™
near water, sinks or bathtubs.
Specifications

GETTING STARTED
POWER OF ENVIRO-BIOTICS™
On/Off Button
Programming
3.Remove sealing foil.
4.Insert the cartridge all the way into
the chamber in the direction of the
arrow printed on the cartridge.
5.Replacechamber cover in a
downward/inward motion with
minimum pressure, until it locks into
place.
Position of the Biodify
1.Press lightly for 2 seconds in order to
turn the Biodify™ on. Repeat this action
when you wish to turn off the unit.
3.Press "Pause" button in order to put
the device on sleep mode for 10 hours.
CAUTION: 
Do not place directly under lights
or other heat sources over 100
degrees. Damage to the
Biodify™may occur.
OperatingButtons (optional)
2.Press "Flake" button in order to
release an extra dose of Enviro-
Biotics™.
2.Shake the
cartridge well.
1. Remove cartridge
chamber cover by an
outward/upward motion
with minimum pressure.
Cartridge Installation
Power Connection
1.Connect the power cord to the inlet
below the Programming buttons. Plug
the power block into anelectricoutlet
within reach of the location you have
chosen for your BIodify™.
WARNING: The
Biodify™should be used only
with the power pack provided
by the manufacturer.
IMPORTANT: Always turn
power off when removing and
replacing cartridge. Also, power
must be turned off before
moving the Biodify.
1. Cartridge must be replaced when
empty, every 2-3 months, depending
onsettingsused.
Cartridge Replacement
1. Your Biodify™should be located out of
the reach ofyoung children or pets. It is
not advised to place the Biodify™ near
an open door or a window that leads
outdoors in order to obtain maximum
coverage indoors.
2.Optimum place forthe Biodify™isin
the middle of a room. The Biodify™ can
sit on top of a shelf, a cabinet or a table
top. It is also recommended to install the
Biodify™ in proximity to
theelectricoutlet using the Wall Mount
(included)
3.Wall Mount installation for optimal
performance:
It is recommended to position the
Biodify™ wall mount in proximity to an
air flow. Drill two screws to fasten the
wall mount on the wall. Make sure that
there is an electric outlet in proximity to
installation for the electric cord to reach.
4.Instead of using the Wall Mount, you
may place the Biodify™ on any flat
surface and stabilize it with the
provided Pedestals. For best results,
place the Biodify™ by a bed, close to a
carpeted area, table tops, bookcases,
shelves etc.