Better Homes and Gardens BH48-084-099-55 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-01-24 Rev. 0001-C
Steele TV Stand
Stock # BH46-084-899-02
# BH48-084-099-55
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Steele TV Stand
MODEL # BH46-084-899-02/BH48-084-099-55
MADE IN MALAYSIA
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted
slightly, turn the appropriate screw as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 50 lb. (22.6 kg)
MÁXIMA CARGA
50 lb. (22.
6
kg)
FITS UP TO MOST 80” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM LOAD 30 lb. (13.6 kg)
2
3

3
Important
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF
WITH DAMP CLOTH.
Insert the wood dowel at least half way by tapping lightly with a rubber mallet IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw cam bolt into the pre-drilled small holes on panel. Connect both panels together; making sure cam
bolt goes into pre-drilled hole on the end of panel with cam lock.
2. Insert cam lock into pre-drilled large hole on panel. Make sure arrow on cam lock is pointed towards cam
bolt.
3. Once cam bolt is connected inside cam lock, take a Phillips screwdriver and tighten cam lock clockwise.
4. Plug cam cap into the cross slot of the cam locks to conceal the cam.
You are now ready to assemble the TV console.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Bottom Panel (Qty. 1) C- Base Front Stretcher (Qty. 1)
D- Base Back Stretcher (Qty. 1) E- Base Side Stretcher (Qty. 2) F- Left Side Panel (Qty. 1)
G- Partition Panel H- Right Side Panel I- Left Door
(Qty. 1) (Qty. 1) (Qty. 1)
J- Right Door (Qty. 1) K- Adjustable Shelf (Qty. 1) L- Back Panel (Qty. 2)
M- Drawer Front (Qty. 2) N- Drawer Back Panel (Qty. 2) O- Drawer Left Side (Qty. 2)
P- Drawer Right Side Q- Drawer Bottom Support R- Drawer Bottom Panel
(Qty. 2) (Qty. 2) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 10+1 extra) (Qty. 12+1 extra) (Qty. 22+1 extra)
(4) M6 x 30 mm Wood Dowel (5) M8 x 30 mm Wood Dowel (6) M3.5 x 15 mm Washer Head Screw
(Qty. 22+1 extra) (Qty. 18+1 extra) (Qty. 48+2 extra)
(7) M4 x 38 mm Screw (8) M4 x 50 mm Screw (9) M3 x 15 mm Pan Head Screw
(Qty. 12+1 extra) (Qty. 12+1 extra) (Qty. 4+1 extra)
(10) Magnetic Catch (11) Corner Connector (12) Shelf Pin
(Qty. 2) (Qty. 4) (Qty. 4+1 extra)
(13) Cam Lock Cover (14) Handle (15) 22 mm Handle Bolt
(Qty. 4+1 extra) (Qty. 4) (Qty. 8)
(16) Floor Leveler (17) M10 x 40 mm Wood Dowel Glue
(Qty. 2) (Qty. 12+1 extra) (Qty. 1)
Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 1) (Included in plastic bag)
Tools required: Phillips screwdriver and hammer (not provided).

6
Drawer Assembling
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Insert four M6 x 30 mm Wood Dowels (4) into the inner holes of the Drawer Back Panel (N). Tap it in
with a rubber mallet, if necessary. Make sure that you use a small amount of glue with both ends of all
dowels.
3. Fasten the Drawer Back Panel (N) to the Drawer Side Panels (O and P) with four 38 mm Screws (7).
7
7
N
P
O
4
4
M6 x 30 mm Wood Dowel
(4 used in this step)
④
M4 x 38 mm Screw
(4 used in this step)
⑦

7
Drawer Assembling
4. Slide the Drawer Bottom Panel (R) into the grooves between the Drawer Side Panels (O and P) until
fully inserted into the Drawer Back Panel (N).
P
R
O
N

8
Drawer Assembling
5. Glue one M6 x 30 mm Wood Dowel (4) into the back center hole of the Drawer Bottom Support (Q)
and attach it to the Drawer Back Panel (N).
M6 x 30 mm Wood Dowel
(1 used in this step)
④
P
O
N
4
Q

9
Drawer Assembling
6. Securely screw five Cam Bolts (3) into the designated small holes on the Drawer Front Panel (M) as
shown.
7. Align and attach the Drawer Front Panel (M) to the Drawer Side Panels (O and P) and the Drawer
Bottom Support (Q) with six M6 x 30 mm Wood Dowels (4) and five Small Cam Locks (1) (Refer to
page 3 on Cam Lock system operation supplement). Make sure that Drawer Bottom Panel (R) fits
securely into the groove of Drawer Front Panel (M).
M
3
3
M
4
4
4
1
1
1
P
O
Q
M6 x 30 mm Wood Dowel
(6 used in this step)
④
Cam Bolt
(5 used in this step)
③
Small Cam Lock
(5 used in this step)
①

10
Drawer Assembling
8. Fasten the Drawer Back Panel (N) to the Drawer Bottom Support (Q) with two 38 mm Screws (7) using
a Phillips screwdriver.
M4 x 38 mm Screw
(2 used in this step)
⑦
7
P
N
O
Q

11
Drawer Assembling
9. Attach one Drawer Handle (14) to the outside of Drawer Front (M) using two provided Handle Bolts
(15).
10. Repeat the same procedure to assemble the other drawer.
15
M
P
O
14
Handle Bolt
(2 used in this step)
Handle
(1 used in this step)
⑭

12
Assembly Instructions
11. Attach two Base Side Stretchers (E) between the Front and Back Stretchers (C and D) with eight Wood
Dowels (5).
12. Using the pilot holes as a guide, attach four Corner Connectors (11) to the Base Side Stretchers (E) at
the inner joints with the provided Washer Head Screws (6). Proceed to fasten the Corner Connetors (11)
to Base Front and Back Stretchers (C and D) with the Washer Head Screws (6).
D
C
E
E
D
C
E
E
C/D
E
5
6
11
M8 x 30 mm Wood Dowel
(8 used in this step)
⑤
Corner Connector
(4 used in this step)
15 mm Washer Head Screw
(8 used in this step)
⑥

13
Assembly Instructions
13. Tightly screw two Floor Levelers (16) into the threaded inserts on the Base Front Stretcher (C) and set
to the correct height.
Floor Leveler
(2 used in this step)
⑯
D
C
E
E
16
16

14
Assembly Instructions
14. Glue ten M8 x 30 mm Wood Dowel (5) into the inner holes of the Bottom Panel (B).
15. Align the large holes on the assembled base with with the inserted Wood Dowels (5) on the Bottom
Panel (B) and press them together. Secure them in place with twelve 50 mm Screws (8).
M4 x 50 mm Screw
(12 used in this step)
⑧
M8 x 30 mm Wood Dowel
(10 used in this step)
⑤
D
C
E
E
B
B
8
C/D/E
5

15
Assembly Instructions
16. Securely screw the Cam Bolts (3) into the designated small holes on the Bottom Panel (B) using a
Phillips screwdriver.
3
B
Cam Bolt
(6 used in this step)
③

16
Assembly Instructions
17. Securely screw six Cam Bolts (3) into the designated small holes on the Top Panel (A) using a Phillips
screwdriver.
18. Align two Magnetic Catches (10) to the pilot holes on the Top Panel (A) as shown. And then attach the
Magnetic Catches (10) in place using two Pan Head Screws (9) per catch.
10
9
3
A
M3 x 15 mm Pan Head Screw
(4 used in this step)
⑨
Magnetic Catch
(2 used in this step)
⑩
Cam Bolt
(6 used in this step)
③

17
Assembly Instructions
19. Glue twelve Wood Dowels (17) into the inner end holes of vertical panels (F, G and H) at both ends.
20. Align and attach the Side Panels (F and H) and Partition Panel (G) between the Top and Bottom Panels
(A and B) by engaging twelve Large Cam Lock (2) as shown.
B
A
F
G
H
2
17
Large Cam Lock
(12 used in this step)
②
M10 x 40 mm Wood Dowel
(12 used in this step)
⑰

18
Assembly Instructions
21. Now, go back and tighten all Cam Locks and Screws. Make sure that all the parts are tight and there are
no gaps between the pieces. This will help keep the unit square.
22. Set the assembly on its front edges. Unfold the Back Panels (L) and lay them to the back edges of the
assembled unit. Make sure that the overlaps on the panels are even all the way around. Attach the Back
Panels (L) in place with the 15 mm Washer Head Screws (6).
NOTE: We recommend attaching back panel with the screws at the corners first.
15 mm Washer Head Screw
(40 used in this step)
⑥
6
L
H
B
L
L
L

19
Assembly Instructions
23. Stand the unit upright.
24. Insert four Shelf Pins (12) into the holes at your desired height inside right compartment. Tilt and rest
the Adjustable Shelf (K) onto the Shelf Pins (12).
25. Plug the Cam Lock Covers (13) onto the visible cam locks to conceal the cams.
Shelf Pin
(4 used in this step)
⑫
12
12
13
F
G
H
A
K
K
Cam Lock Cover
(4 used in this step)
⑬

20
Assembly Instructions
26. Attach one Handle (14) to the front side of each Door (I and J) with the provided Handle Bolts (15).
27. Pick up Left Door (I) and attach the extended Hinge Arms to the Hinge Bases installed on the Partition
Panel (G). Loosen the bolt on the back of Hinge Base for an easy fit. Align and insert the “U” slot on
Hinge Arm under the bolt head on the back of Hinge Base. Make sure that both door hinges engage and
function properly. Tighten the bolt on the Hinge Base to lock the hinges in place.
28. Repeat the same procedure to attach the Right Door (J) to the Right Side Panel (H).
29. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the
screws for a good fit. Refer to the hinge sticker on door for adjustment.
J
14
I
14
15 15
2
G
H
A
I
J
Handle
(2 used in this step)
⑭
Handle Bolt
(4 used in this step)