Better Homes and Gardens Steele Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-09-24 Rev. 0001-A Factory: HESLTD
Steele Coffee Table
Stock # BH46-021-399-01
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOGUE: Steele Coffee Table (BH46-021-399-01)
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 200 lb. (90.7 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 50 lb. (22.6 kg)

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the fireplace.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Bottom Panel (Qty. 1)
C- Bottom Long Support (Qty. 2) D- Bottom Short Support (Qty. 2)
E- Left Front/Right Back Panel (Qty. 2) F- Left Front/Right Back Side Panel (Qty. 2)
G- Right Front/Left Back Panel (Qty. 2) H- Right Front/Left Back Side Panel (Qty. 2)
(1) Cam Lock (2) Cam Bolt
(Qty. 24+1 extra) (Qty. 24+1 extra)
(3) M8 x 30 mm Wood Dowel (4) M10 x 40 mm Wood Dowel (5) M4 x 50 mm Screw
(Qty. 16+1 extra) (Qty. 16+1 extra) (Qty. 26+1 extra)
(6) Cam Lock Cover (Qty. 24+1 extra) Glue (Qty. 1) Touch-up Pen (Qty. 1)
Tools required: Phillips screwdriver and hammer (not provided).

5
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Panels (A, E and G) using a
Phillips screwdriver.
2
A
E E
G G
Cam Bolt
(24 used in this step)
②

6
Assembly Instructions
3. Attach one Left Front Side Panel (F) to one Left Front Panel (E) with one 30 mm Wood Dowel (3) and
two Cam Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
4. Repeat the previous step to combine the Right Back Side Panel (F) with the Right Back Panel (E)
together.
5. Repeat the same procedure with the Right Front/Left Back Side Panels (H) and Right Front/Left Back
Panels (G) together.
G
H1
x 2
E
F
3
1
x 2 3
Cam Lock
(8 used in this step)
①
M8 x 30 mm Wood Dowel
(4 used in this step)
③

7
Assembly Instructions
6. Attach the previous assemblies to the Top Panel (A) with eight 40 mm Wood Dowels (4) and sixteen
Cam Locks (1) as shown.
Cam Lock
(16 used in this step)
①
A
4
E
F
F
E
G
H
GH
41
M10 x 40 mm Wood Dowel
(8 used in this step)
④

8
Assembly Instructions
7. Attach the Bottom Panel (B) to the side panels with eight 40 mm Wood Dowels (4) and sixteen 50 mm
Screws (5).
M4 x 50 mm Screw
(16 used in this step)
⑤
M10 x 40 mm Wood Dowel
(8 used in this step)
④
A
E
F
F
E
G
H
GH
B
4
4
5

9
Assembly Instructions
8. Attach the Bottom Short Supports (D) between the Bottom Long Supports (C) with four 30 mm Wood
Dowels (3).
9. Fasten the previous assembly to the Bottom Panel (B) with eight 30 mm Wood Dowels (3) and ten 50 mm
Screws (5).
B
3
3
3
3
D
D
C
C
C
C
D
D
3
5
M8 x 30 mm Wood Dowel
(12 used in this step)
③
M4 x 50 mm Screw
(10 used in this step)
⑤

10
Assembly Instructions
10. Stand the assembled unit upright.
11. Plug the Cam Lock Covers (6) onto the visible Cams Locks to conceal the cams.
6
Cam Lock Cover
(24 used in this step)
⑥

11
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage your furniture’s finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during assembly or
shipping. We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace
it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your
highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State
(province to province).
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2016-09-24 Rev. 0001-A Fábrica: HESLTD
Mesa de centro Steele
Serie # BH46-021-399-01
ENSAMBLE REQUERIDO POR ADULTO
Si tiene alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a
la tienda en que lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estandar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
O visite nuestra página de Internet 24 horas al dia, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: / /

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Mesa de centro Steele (BH46-021-399-01)
HECHO EN CHINA
NOTA ESPECIAL
Por favor lea todo el instructive antes de ensamblar. Examinar todo el material de
empaque antes de tirar el cartón. Retirar cualquier grapas del cartón antes de tirar. Retirar
todas las partes del cartón y separar en grupos como es indicado en la lista de partes. Por
favor de asegurar que todas las partes estan presentes antes del ensamble. El uso de
herramientas eléctricas para completer el ensamble no es recomendado.
MÁXIMOS PESOS RECOMENDADOS
MÁXIMA CARGA 200 lb. (90.7 kg)
MÁXIMA CARGA 50 lb. (22.6 kg)
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES
.

3
IMPORTANTE
Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre
una superficie plana y no abrasiva. Tendrá que las partes identificadas en la página 4 de este manual de
instrucciones.
NOTA: ES MUY IMPORTANTE PARA EL USO DE GOMA CON LOS PERNSO DE MADERA. EL.
EXCESO DE PEGAMENTO SE PUEDE LIMPIAR CON UN PAÑO HÚMEDO.
Inserte el perno por lo menos a la mitad del camino golpeando ligeramente con un mazo de goma SI ES
NECESARIO.
SISTEMA DE OPERACIÓN DE TUERCA DE FIJACIÓN
CÓMO FUNCIONA LA INSTALACIÓN DE MONTAJE (KD)
1. Fijar los tornillos de fijación en los orificios pequeños. Conectar ambos paneles, cerciorandose que los
tornillos de fijación entren bien y que estos queden en los orificios al final del panel con tuercas de fijación.
2. Inserte las tuercas de fijación en los orificios grandes del panel. Hacer que la flecha en la tuerca este
apuntando hacia la entrada del tornillo de fijación.
3. Una vez que el tornillo este conectado dentro, tome un destornillador de cruz y apriete la tuerca en
dirección de las manecillas del reloj.
4. Coloque la tapa de la tuerca de fijación sobre la misma en la ranura de cruz, ver detalle.
Está listo para el ensamble KD de esta unidad.
XX
FINAL
1 2 43

4
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el
ensamblado.
A- Panel superior (Cant. 1) B-
Panel inferior (Cant. 1)
C- Soporte inferior largo (Cant. 2) D- Soporte inferior corto (Cant. 2)
E- Panel frontal izq./der. posterior (Cant.2) F-
Panel lateral frontal izq./der. posterior (Cant. 2)
G- Panel derecho frontal/izq, posterior (Cant. 2) H- Panel lateral frontal der/izquierdo posterior Cant. 2)
(1) Tuerca de fijación (2) Tornillo de fijación
(Cant. 24+1 extra) (Cant. 24+1 extra)
(3) Perno M8 x 30 mm madera (4) Perno M10 x 40 mm madera (5) Tornillo M4 x 50 mm
(Cant. 16+1 extra) (Cant.16+1 extra) (Cant. 26+1 extra)
(6) Tapa de tuerca (Cant. 24+1 extra) Pegamento (Cant. 1) Plumón de retoque (Cant. 1)
Herramientas requeridas: Desarmador estrella y mazo (no proveido).

5
Instrucciones de ensamble
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños.
2. Ajuste los tornillos de fijación (2) en los orificios pequeños designados en los paneles (A, E y G) con un
desarmador estrella.
2
A
E E
G G
Tornillo de fijación
(24 usados en este paso )
②

6
Instrucciones de ensamble
3. Coloque un panel lateral frontal izquierdo (F) para un panel frontal izquierdo (E) con un perno de 30
mm de madera (3) y dos tuercas de fijación (1) (Consulte la página 3 del sistema de tuerca de fijación y
su operación).
4. Repita el paso anterior para combinar el panel lateral posterior derecho (F) con el panel posterior
derecho (E) juntamente.
5. Repetir el mismo procedimiento con los paneles laterales frontales derechos/posterior izquierdos (H) y
los paneles frontales derecho/izquierdo posteriores (G), juntamente.
G
H1
x 2
E
F
3
1
x 2 3
Tuerca de fijación
(8 usados en este paso )
①
Perno M8 x 30 mm de madera
(4 usados en este paso)
③

7
Instrucciones de ensamble
6. Coloque los montajes anteriores al panel superior (A) con ocho pernos de 40 mm de madera (4) y
dieciséis tuercas de fijación (1) como se muestra.
Tuerca de fijación
(16 usados en este paso )
①
A
4
E
F
F
E
G
H
GH
41
Perno M10 x 40 mm de madera
(8 usados en este paso )
④

8
Instrucciones de ensamble
7. Coloque el panel inferior (B) a los paneles laterales con ocho pernos de 40 mm de madera (4) y dieciséis
tornillos de 50 mm (5).
Tornillo M4 x 50 mm
(16 usados en este paso )
⑤
Perno M10 x 40 mm de madera
(8 usados en este paso)
④
A
E
F
F
E
G
H
GH
B
4
4
5