Classic Exhibits RE-2015 User manual

Locked layer contains
placeholder marks.
Plan View
10’
20’
RE-2015
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
10’ x 20’ Display

DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
RE-2015

Step 1 of 3
Locked layer contains
placeholder marks.
Item Qty Description
1 4 Base Plate
2/2a 2/2 42” OP91 Vertical Extrusion
3/3a 2/2 42” OP91 Vertical Extrusion
4/4a 1/1 44” RSG531 Vertical Extrusion
5/5a 1/1 44” RSG531 Vertical Extrusion
6a/6b 2/2 29.5” Z45 Curved Horizontal Extrusion
7a/7b 2/2 29.5” Z45 Curved Horizontal Extrusion
8a/8b 2/2 38” Z45 Horizontal Extrusion
9/9a 1/1 46.126” Z45 Horizontal Extrusion
10 1 46.126” Z140 Horizontal Extrusion
Steps:
1) Attach base plates to bottom of verticals [2 & 3] as shown, see Detail D on General Instruction page.
2) Connect upper verticals [2a to 2], [3a to 3], [4a to 4] and [5a to 5] as shown.
3) Connect horizontals [6a to 6b] and [7a to 7b] together as shown.
4) Connect horizontal extrusions [6a/6b,7a/7b,8a,8b,9,9a & 10] between vertical assemblies as shown.
5) Attach graphics to velcro on front of backwall as shown.
11
2
2a
4
4a
1
3
3a
1
3
3a
1
2
2a
5
5a
9a
9
10
6a
7a
8a
8b
8a
8b
7b
6b
6a
7a 7b
6b
Velcro
Velcro
Velcro Velcro
Velcro
Velcro
Velcro
Velcro
Velcro Velcro
Attach graphic
to velcro on front
of frame
Attach graphic
to velcro on front
of frame
Attach graphic
to velcro on front
of frame
Backwall Assembly
RE-2015

Step 2 of 3
Locked layer contains
placeholder marks.
Steps:
1) Attach base plates to bottom of verticals [11,11a] see Detail D on General Instruction page.
2) Connect verticals [11,11a] to backwall structure using horizontal extrusions [12].
3) Connect header pieces [13a/13b, 14a/14b, 15, 16 and 17] together as shown.
**Velcro must face forward and must be attached on edges of frame.**
4) Connect assembled header between vertical assemblies as shown.
1
11
1
11a
13a
13b
14a
14b
12
15
16 17
12
Note: Attaching Graphics
Attach Header Graphic to Velcro on
the front of header frame
Item Qty Description
1 2 Base Plate
11/11a 1/1 96” OP91 Vertical Extrusion
12 2 30” Z45 Horizontal Extrusion
13a/13b 1/1 48.4” Z31 Curved Horizontal Extrusion
14a/14b 1/1 48.4” Z31 Curved Horizontal Extrusion
15 1 11.5” Z33 Vertical Extrusion
16 1 11.5” Z33 Vertical Extrusion
17 1 11.5” Z33 Vertical Extrusion
Header Assembly
RE-2015

Step 3 of 3
Locked layer contains
placeholder marks.
Steps:
1) Attach lights to top of backwall as shown.
2) Attach large monitor mount to horizontal [10] as shown in detail.
3) Attach small monitor mounts to verticals as shown in detail.
4) Attach shelves to verticals as shown in detail.
*
*
**
*
*
*
*
*
**
Small Monitor
Mount Attachment
Shelf Attachment
Attach back plate to connectors
on vertical extrusion using screws.
Then attach top plate and tighten
setscrews to secure.
Connect shelf to shelf supports, attach to
verticals and tighten lock to secure in place.
Attach wall plate
to panels using
bolts and wing nuts
Monitor Mount Attachment
*
Attachments
RE - 2015