Better Homes and Gardens Mercer BH15-084-299-03 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Manufacturing Page 1 Factory No. 16434
Date 2015-06-29 Rev. 1 Factory: DOSHFU
Mercer Dining Table
Stock # BH15-084-299-03
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

Stock # BH15-084-299-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 2 Factory No. 16434
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will
repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product
is designed to meet your highest expectations. We guarantee that you will immediately see the
value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary
from State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Mercer Dining Table (BH15-084-299-03)
MADE IN CHINA
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH LOADS HEAVIER THAN THE
MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING
POSSIBLE INJURY.
MAXIMUM LOAD 400 lb. (181.4 kg)

Stock # BH15-084-299-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 3 Factory No. 16434
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1) B- Leg (2)
C- Top
Stretcher (1) D- Bottom Stretcher (1)
(1) Ø1/4” x 5/8” Bolt (2) Ø1/4” x 2-3/8” Bolt (3) Small Lock Washer
(8+1 extra) (2+1 extra) (10+1 extra)
(4) Small Flat Washer (5) Ø5/16” x 3-1/4” Bolt (6) Large Lock Washer
(10+1 extra) (6+1 extra) (6+1 extra)
(7) Large Flat Washer (6+1 extra) 4 mm Allen Wrench (1) 5 mm Allen Wrench (1) Touch-up Pen (1)
Tools required: Allen wrench (provided) and Phillips screwdriver (not provided).

Stock # BH15-084-299-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 4 Factory No. 16434
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Position the Table Top (A) upside down on a level and protective surface, as shown above.
3. Remove the additional wood blocks attached at the corners by unscrewing the wood screws. These are used
for shipping purposes only. After removing them, please discard.
A

Stock # BH15-084-299-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Manufacturing Page 5 Factory No. 16434
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
4. Align and attach the Top and Bottom Stretchers (C and D) between two Legs (B) by using eight 5/8” Bolts
(1) with the Small Lock Washers (3) and Flat Washers (4) through the end brackets and screw into the
threaded sockets on legs.
B
C
DB
134
134
1
3
4
1
3
4
Small Lock Washer
(8 used in this step)
③
Small Flat Washer
(8 used in this step)
④
Ø1/4” x 5/8” Bolt
(8 used in this step)
①