Better Homes and Gardens Oaklee BHS336158813026 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-04-12 Rev. 0001-A
Black Brass End Table
Stock # BHS336158813026
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Black Brass End Table
MODEL # BHS336158813026
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D
E D W E I G H T
L O
A D S
MAXIMUM LOAD 22.7 kg / 50 lb.
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 6.8 kg / 15 lb.
MAXIMUM LOAD 22.7 kg / 50 lb.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the dowel at least halfway by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
You are now ready to assemble the KD unit.
GLUE
FINAL
1 2 43
13
123

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A-Top Panel (Qty. 1)
B- Left Side Frame C- Right Side Frame D- Bottom Panel
(Qty. 1) (Qty. 1) (Qty. 1)
E- Back Panel F- Crossbar G- Drawer Front
(Qty. 1) (Qty. 1) (Qty. 1)
H- Drawer Back Panel I- Drawer Left Side Panel J- Drawer Right Side Panel
(Qty. 1) (Qty. 1) (Qty. 1)
K- Drawer Bottom Support L- Drawer Bottom Panel M- Handle
(Qty. 1) (Qty. 1) (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock
(Qty. 6+1 extra) (Qty. 14+1 extra)
(3) Cam Bolt (4) M6 x 30 mm Wood Dowel (5) M8 x 30 mm Wood Dowel
(Qty. 20+1 extra) (Qty. 4+1 extra) (Qty. 12+1 extra)
(6) M3.5 x 15 mm Screw (7) M4 x 30 mm Screw (8) 1/4” x 20 mm Bolt
(Qty. 8+1 extra) (Qty. 6+1 extra) (Qty. 4+1 extra)
(9) Flat Washer (10) Metal Bracket (11) 5/32” x 22 mm Bolt
(Qty. 4+1 extra) (Qty. 4) (Qty. 2)
Hex Wrench Glue Touch-up Pen
(Qty. 1) (Qty. 1) (Qty. 1)
Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).

6
Assembly Instructions
NOTE: Please do not fully tighten all cam locks and screws until you finish assembling all parts. Once
assembled, go back and fully tighten all cam locks and screws. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (3) into the designated small holes on the Drawer Front (G) using a
Phillips Screwdriver. DO NOT over tighten the cam bolts.
③ x 6
3
G

7
Assembly Instructions
3. Glue the Small Wood Dowels (4) into the inner holes of the Drawer Back Panel (H) and Drawer Side
Panels (I and J).
NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the
excess glue immediately with a damp cloth.
4
4
44
4
H
I
J
④ x 4

8
7
7
I
JH
Assembly Instructions
4. Orient and attach the Drawer Back Panel (H) between the Drawer Side Panels (I and J) with four 30 mm
Screws (7).
Grooves line up with each
other and face inward
⑦ x 4

9
Assembly Instructions
5. Slide the Drawer Bottom Panel (L) into the grooves on both Drawer Side Panels (I and J) until fully
inserted into the Drawer Back Panel (H).
H
J
I
L

10
7
H
K
Assembly Instructions
6. Orient and attach the Drawer Bottom Support (K) to the Drawer Back Panel (H) with two 30 mm
Screws (7).
The cam lock housings face outward
⑦ x 2

11
Assembly Instructions
7. Stand the previous assembly at its back panel.
8. Position the Drawer Front Panel (G) onto the inserted Wood Dowels (4) and fasten it in place by engaging
six Small Cam Locks (1). (Refer to page 3 on Cam Lock system operation supplement). Make sure that
the Drawer Bottom Panel (L) fits securely into the groove of the Drawer Front (G).
① x 6
K
I
J
G
1
1
1
L

12
Assembly Instructions
9. Install one Handle (M) to the front of Drawer Front (G) with two 22 mm Bolts (11).
x 2
11
M
G

13
③ x 14
Assembly Instructions
10. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A) and Side Frames
(B and C) using a Phillips screwdriver.
3
B
C
A

14
Assembly Instructions
11. Glue the Large Wood Dowels (5) into the inner holes on the Side Frames (B and C), Back Panel (E) and
Crossbar (F) as shown.
⑤ x 12
5
5
EF
B
C
5
55
5

15
C
2
E
E
C
Assembly Instructions
12. Orient and attach the Back Panel (E) to the Right Side Frame (C) by engaging 2 Large Cam Locks (2).
The cam lock housings
face inwa
rd
② x 2
Wood dowels

16
F
C
2 F
C
Assembly Instructions
13. Align and attach the Crossbar (F) to the Right Side Frame (C) by engaging 2 Large Cam Locks (2).
The cam lock housings are
oriented dow
nward
② x 2

17
Assembly Instructions
14. Using the pilot holes as a guide, fasten four Metal Brackets (10) to the corners of Bottom Panel (D) with
eight 15 mm Screws (6).
⑩ x 4 ⑥ x 8
D
10
6
10
6

18
Assembly Instructions
15. Align the Metal Brackets (10) installed on the Bottom Panel (D) with the threaded inserts on the Right
Side Frame (C) properly and secure them into place using two 20 mm Bolts (8) and two Flat Washers
(9).
⑨ x 2
⑧ x 2
8
10 9
C
D
D

19
Assembly Instructions
16. Attach the Left Side Frame (B) to the Back Panel (E) and Crossbar (F) by engaging 4 Large Cam Locks
(2).
② x 4
2
E/F
F
E
B
B

20
Assembly Instructions
17. Insert two 20 mm Bolts (8) with the Flat Washers (9) through the Metal Brackets installed on the
Bottom Panel (D) and securely screw into the Left Side Frame (B).
⑨ x 2
⑧ x 2
8
9
B
D
D
B