Better Homes and Gardens BH48-084-097-02 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-08-30 Rev. 0001-A
Adjustable Bed
Stock # BH48-084-097-02 Gunmetal
# BH48-084-097-03 White
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Left Headboard B- Right Headboard C- Right Footboard
(Qty. 1) (Qty. 1) (Qty. 1)
D- Left Footboard E- Long Side Rail F- Short Side Rail
(Qty. 1) (Qty. 2) (Qty.2)
G- Finial H- Slat Support I- Long Slat for Slat Support
(Qty. 4) (Qty. 4) (Qty. 4)
J- Long Slat K- Short Slat L- Twin HB/FB Long Connector
(Qty. 13) (Qty. 34) (Qty. 3)
M- Twin HB/FB Short Connector N- Full HB/FB Connector O- Full HB/FB Cross Assembly
(Qty. 4) (Qty. 3) (Qty. 2)
P- Queen HB/FB Connector Q- Queen Bed Cross Assembly R- Queen Side Rail Filler
(Qty. 3) (Qty. 2) (Qty. 2)
(1) 1/4" x 5/8” Bolt (Qty. 86+2 extra) (2) 1/4" x 1 1/4” Bolt (Qty. 4+1 extra) Hex Wrench (Qty. 2)
Tools required: Hex wrench (provided).

3
Assembly Instructions
NOTE: The adjustable bed provides three configurations: Twin Bed, Full Bed or Queen Bed. Please
choose the option that best suits your needs. DO NOT discard any of the hardware or parts that you will
not use on your chosen option. This will allow you to use this bed in different configurations at a late date,
if desired. Please follow the instructions carefully to insure a safe and sturdy bed. Do not fully tighten the
bolts until all parts are attached.
1. Unpack the units and confirm that you have all hardware and required parts. Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Choose the desired configuration, fit the proper Connectors (L, M, N or P) and Cross Assembly (O or Q)
between the Left and Right Headboards (A and B). Make sure the mounting holes overlap the threaded
sockets on the Long Connectors (L, N or P) properly. Proceed to secure them in place with four 5/8” Bolts (1).
1/4" x 5/8” Bolt
(4 used in this step)
①

4
Assembly Instructions
3. Choose the desired configuration, fit the proper Connectors (L, M, N or P) and Cross Assembly (O or Q)
between the Left and Right Footboards (C and D). Make sure the mounting holes overlap the threaded
sockets on the Long Connectors (L, N or P) properly. Proceed to secure them in place with two 5/8” Bolts (1).
1/4" x 5/8” Bolt
(2 used in this step)
①

5
Assembly Instructions
4. Combine the Long Side Rail (E) and Short Side Rail (F) together with two 5/8” Bolts (1). NOTE: If you
choose queen bed configuration, be sure to add the Queen Side Rail Filler (R) as shown above.
5. Repeat the same procedure to form the other Side Rails.
1/4" x 5/8” Bolt
(4 used in this step)
①

6
Assembly Instructions
6. Fasten the Side Rail assembly between the Headboard (A and B) and Footboard (C and D) with eight 5/8”
Bolts (1).
1/4" x 5/8” Bolt
(8 used in this step)
①

7
Assembly Instructions
7. Combine one Long Slat (J) and two Short Slats (K) together with two 5/8” Bolts (1) as shown above.
8. Repeat the same procedure with the other Slats (J and K).
NOTE: The queen bed needs one more slat than twin and full size bed.
1/4" x 5/8” Bolt
(24 used in this step)
①
1/4" x 5/8” Bolt
(26 used in this step)
①
1/4" x 5/8” Bolt
(24 used in this step)
①

8
Assembly Instructions
9. Repeat the same procedure to combine one Long Slat for Slat Support (I) and two Short Slats (K)
together.
10. Fasten the Slat Support (H) to the center of each Long Slat (I) with one 1 1/4” Bolt (2).
1/4" x 1 1/4” Bolt
(4 used in this step)
②
1/4" x 5/8” Bolt
(8 used in this step)
①

9
Assembly Instructions
11. Fit the slat assemblies between the assembled side rails and fasten them in place with the 5/8” Bolts (1).
1/4" x 5/8” Bolt
(32 used in this step)
①
1/4" x 5/8” Bolt
(34 used in this step)
①

10
Assembly Instructions
12. Screw the Finials (G) onto the Headboard and Footboard posts to finish the assembly.
13. The bed is now ready for use.

11
Care and Maintenance
 For everyday cleaning, chrome, brass, aluminum, and painted metal surfaces can be kept looking their best
by wiping with a slightly damp, soft cotton cloth or vacuum cleaner brush.
 If soiled, wipe with clean sponge or cloth wrung out of water. Wipe dry with cloth or paper towel to avoid
water spots.
 Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the protective
coating.
 Metal will rust if the finish is scratched or if your furniture is exposed to excessive humidity, particularly in
salt water locations.
 Most metal furniture has a protective coating to prevent rust, however rust may occur if the finish is marred
or wears away over time.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice About Metal Furniture Care
It is best to keep your furniture in a climate-controlled environment. Continual exposure to damp and wet
environment can cause corrosion. It is advised to keep furniture away from direct sunlight as it may damage the
finish. Indoor furniture is not recommended for outdoor use.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State
to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2018-08-30 Rev. 0001-A
Cama ajustable
Modelo # BH48-084-097-02 Gris Metal
# BH48-084-097-03 Blanco
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto
a la tienda donde lo compro. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
O visite nuestra página de Internet 24 horas al día, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
NÚMERO de LOTE:
FECHA de COMPRA: / /

2
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de
iniciar el ensamblado.
.
A- Cabecera izquierda B- Cabecera derecha C- Piecera derecha
(Cant. 1) (Cant. 1) (Cant. 1)
D- Piecera izquierda E- Riel lateral largo F- Riel lateral corto
(Cant. 1) (Cant. 2) (Cant.2)
G- Molduras decorativas H- Soporte de tablilla I- Tablilla larga para soporte de tablilla
(Cant. 4) (Cant. 4) (Cant. 4)
J- Tablilla larga K- Tablilla corta L- Conector largo individual HB/FB
(Cant. 13) (Cant. 34) (Cant. 3)
M- Conector corto individual HB/FB N- Conector familiar HB/FB O- Ensamble de soporte familiar HB/FB
(Cant. 4) (Cant. 3) (Cant. 2)
P- Conector matrimonial HB/FB Q- Ensamble de soporte cama matrimonial R- Relleno del riel lateral matrimonial
(Cant. 3) (Cant. 2) (Cant. 2)
(1) Perno de 1/4" x 5/8” (Cant. 86+2 extra) (2) Perno de 1/4" x 1 1/4” (Cant. 4+1 extra) Llave hexagonal (Cant. 2)
Herramientas requeridas: Llave hexagonal (provista).

3
Instructivo de ensamble
NOTA: La cama ajustable ofrece 3 configuraciones: Cama Twin, Cama Full o Cama Queen. Por favor
elija la opción que será mejor para sus necesidades. NO tire ninguna pieza o herraje que no va a usar en su
opción elegida. Esto le permitirá usar la cama en diferentes configuraciones en el futuro, si lo desea. Por
favor siga las instrucciones cuidadosamente para asegurar de que la cama sea fuerte y segura. No apriete
completamente los pernos hasta que todas las partes estén adjuntas.
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños.
2. Elija la configuración deseada, y encajar los conectores apropiados (L, M, N o P) y el ensamble de soporte
(O o Q) entre las cabeceras izquierda y derecha (A y B). Asegurar que los agujeros de montaje estén sobre
los espacios roscados en los conectores largos (L, N o P) apropiadamente. Preceder a asegurar 4 pernos de
5/8” (1) en su lugar.
Perno de 1/4" x 5/8”
(4 usados en este paso)
①

4
Instructivo de ensamble
3. Elija la configuración deseada, y encajar los conectores apropiados (L, M, N o P) y el ensamble de soporte
(O o Q) entre las pieceras izquierda y derecha (C y D). Asegurar que los agujeros de montaje estén sobre
los espacios roscados en los conectores largos (L, N o P) apropiadamente. Preceder a asegurar 2 pernos de
5/8” (1) en su lugar.
Perno de 1/4" x 5/8”
(2 usados en este paso)
①

5
Instructivo de ensamble
4. Combinar el riel lateral largo (E) y el riel lateral corto (F) con 2 pernos de 5/8” (1). NOTA: Si elige la
configuración cama Queen, asegúrese de adjuntar el relleno del riel lateral Queen (R) como se muestra.
5. Repetir el mismo procedimiento para formar los otros rieles laterales.
Perno de 1/4" x 5/8”
(4 usados en este paso)
①

6
Instructivo de ensamble
6. Sujetar el ensamble del riel lateral entre la cabecera (A y B) y la piecera (C y D) con 8 pernos de 5/8” (1).
Perno de 1/4" x 5/8”
(8 usados en este paso)
①

7
Instructivo de ensamble
7. Combinar una tablilla larga (J) y 2 tablillas cortas (K) con 2 pernos de 5/8” (1) como se muestra arriba.
8. Repetir el mismo procedimiento con las otras tablillas (J y K).
NOTA: La cama matrimonial necesita una tablilla más que la cama individual y familiar.
Perno de 1/4" x 5/8”
(24 usados en este paso)
①
Perno de 1/4" x 5/8”
(26 usados en este paso)
①
Perno de 1/4" x 5/8”
(24 usados en este paso)
①

8
Instructivo de ensamble
9. Repetir el mismo procedimiento para combinar una tablilla larga o un soporte de tablilla (I) y 2 tablillas
cortas (K).
10. Sujetar el soporte de tablilla (H) al centro de cada tablilla larga (I) con un perno de 1 /14” (2).
Perno de 1/4" x 1 1/4”
(4 usados en este paso)
②
Perno de 1/4" x 5/8”
(8 usados en este paso)
①