WATSON D9 User manual

USER GUIDE
D9 Height Adjustable Desk
V.19.1 09/2019 watsonfurniture.com360.394.1300

2 D9 HEIGHT ADJUSTABLE DESK USER GUIDE
OPERATING INSTRUCTIONS – Please refer to the provided Installation Instructions and User Guide.
POLARIZED PLUG INSTRUCTIONS – To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider than
the other). This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse the plug. If it still does
not t, contact a qualied electrician to install the proper outlet. Do not change the plug in any way.
SERVICING OF DOUBLE-INSULATED PRODUCTS – In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated product, nor is a means for grounding to be added to the product.
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by qualied service
personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double-insulated product
is marked with the words “DOUBLE INSULATION”, “DOUBLE INSULATED”, or .
This product is for use on a nominal 120-V circuit. Make sure that the product is connected to an outlet having the same
conguration as the plug. No adapter should be used with this product.
IMPORTANT SAFETY INSTRUCTIONS
DANGER -
To reduce the risk of electric shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING -
To reduce the risk of burns, re, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking off parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, turn all controls to the off position, then remove the plug from outlet.
10. For loading always put heavier items at the bottom and not near the top in order to help prevent the possibility of the
furnishing tipping over.
This product is for commercial use only.
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using (this furnishing).
SAVE THESE INSTRUCTIONS

3 D9 HEIGHT ADJUSTABLE DESK USER GUIDE
CARE & MAINTENANCE
Surface Laminate
To clean the surface, use mild soap or detergent with a damp cloth or sponge. Difcult stains such as coffee or tea
can be removed by using mild household cleaner and baking soda; mixing to achieve a paste consistency. Gently wash
(approximately 15-20 strokes) the affected area using a stiff nylon bristle brush. Do not scrub so as to scratch the
surface nish. Avoid cleaners with ammonia.
Marker Board Laminate
Wilsonart Marker Board Laminate can be cleaned using a felt or multi-purpose board eraser. When additional cleaning
is required, a soft cloth dampened with warm tap water and mild soaps, such as those used for hands or dishes, is
recommended. Remember to clean erasers often by wiping to remove dry-erase marker residue.
Stubborn Stains
Stubborn stains that resist any of the mentioned cleaning methods may require the use of undiluted household bleach
or nail polish remover. Use a cotton ball saturated with bleach or nail polish remover (acetone), gently rub the stain for
up to two minutes. Rinse thoroughly with warm water and wipe dry with a soft cloth. This step may be repeated if the
stain appears to be going away and the color of the laminate has not been affected.
Note — Scrubbing too hard or at length can damage the surface nish.
If stubborn stains persist, Marker Board Laminate can be cleaned with spray-type glass cleaners, such as Windex®. Do
not use cleansers that contain abrasives, acids or alkalis; they will damage the surface. Remove stubborn stains with a
2-minute exposure to hypochlorite bleach, such as Clorox®, followed by a clean water rinse.
Storage
When not in use for an extended period of time, always unplug this furnishing from the electrical outlet and carefully
stow the power cord to avoid accidental damage.
WARNING: Always rinse laminate surfaces after cleaning. Cleaning solutions may leave behind a residue that can
be reactivated by moisture from cups or drinks. Prolonged exposure to cleaning residues can cause permanent
discoloration, scars, or stains in laminate surfaces.
CAUTION: For normal cleaning, vacuum panel fabric as needed, using an upholstery attachment. Do not brush fabric or
use a vacuum attachment with a rotary brush. Brushing may permanently damage the nap or change the character of
the fabric.

4 D9 HEIGHT ADJUSTABLE DESK USER GUIDE
PRODUCT SPECIFICATIONS
Range of Adjustment Electric — 28”-48” (29”-
49” w/ casters)
Glide Adjustment 1/4"
Max. Weight Capacity 250lbs
Wire Management
Included
No
Controller Up/Down
Decibel Rating 50db(A) in typical
applications
Volts 120v AC
Frequency & Phase 50 Hz - 60 Hz, Single
Phase
Amps 2.5 A
Watts 300 W
Standby 0.1W
Adjustability Speed 1.5"/sec
Duty Cycle Max 2 min ON/18 min OFF
WORKSTATION TIPS
Ensure that power cords for all accessory items have enough length to reach the outlets throughout the full range of the
table adjustment. Do not subject cords to any strain while adjustment of the surface is taking place.
Always check for proper operating clearance before placing any item on, above, or below the worksurface.
HEIGHT ADJUSTMENT
The controller switch has two buttons for user control.
• Press and hold either the up or down button to reach the desired desk height.
• The desk will continue to move up or down until the user releases the button or the maximum or minimum
height is reached.
Note: As a safety feature, the user must continuously hold down the button for the desk to move.
D9 Controller Switch

5 D9 HEIGHT ADJUSTABLE DESK USER GUIDE
If the desk does not move up or down:
1Connect a lamp, or similar object, to the main power supply to verify there is adequate voltage.
2Check all accessible cable connections and verify there is no visible damage to cables, controls, control boxes or legs.
3 If all systems appear intact, unplug the desk for ve minutes then plug the desk back in, and perform a Reset. If the problem
persists, contact your facility administrator.
If the desk stops and will only retract, check the following:
1Verify that the desk is fully extended. When the desk has reached its uppermost position it can only run downward.
2Remove some of the load and try again.
If the problem persists, perform a Reset.
If the desk will only adjust downward even though the desk is not overloaded, perform a Reset.
If the desk does not move all the way up and repeatedly stops at the same position, perform a Reset.
If the desk collides with an object, follow these steps:
1Adjust the desk up or down, away from the obstruction.
2Perform a Reset.
RESET
Operate the desk down to the lowest position and release the down button.
Press and hold the down button for several seconds.
The desk should visibly move up and down signaling that the reset is complete.
Operate the desk throughout its range of motion to ensure proper function.
TROUBLESHOOTING
3
1
2
3
4