Sauder 426927 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-20
Français pg 21-24
Español pg 25-28
Lot # 543097 03/19/20
Purchased: __________________
Wardrobe
Model 426927
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-20
21-24
25-28
29-30
31
Hammer
Not actual size
Electric drill with 1/8" bit
(ONLY in indicated step)
Page 2 www.sauder.com/service 426927

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C DOOR (2)
D BACK (1)
E TOP/BOTTOM (2)
F SHELF (1)
G BRACE (1)
H BACK SKIRT (1)
J FRONT SKIRT (1)
A
B
C
DE
F
G
H
J
C
E
Page 3www.sauder.com/service426927

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
WOOD DOWEL -6
1METAL BRACKET - 5
2 3 HINGE - 6 NAIL - 52 4
PULL - 2
56BUMPER CARD - 1 APPLIQUE CARD - 1
7
FURNITURE TIPPING RESTRAINT KIT - 1
988 ROD HANGER - 2 ROD - 1 9
15/16" PAN HEAD SCREW - 4
12
11 1-9/16" FLAT HEAD SCREW - 16
1/2" FLAT HEAD SCREW - 48
10
Page 4 www.sauder.com/service 426927

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten a ROD HANGER (8) to the LEFT END (A). Use two
1/2" FLAT HEAD SCREWS (10).
A
8
1/2" FLAT HEAD SCREW
(2 used in this step)
10
Page 5www.sauder.com/service426927
Just think. The sooner
you do this, the sooner
you do something else.

å Fasten the TOP/BOTTOMS (E) and SHELF (F) to the
LEFT END (A). Use six 1-9/16" FLAT HEAD SCREWS (11).
Step 2
A
E
E
F
Surface with
no holes
Surface with holes
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1-9/16" FLAT HEAD SCREW
(6 used in this step)
11
Unfinished edge
Unfinished edge
Page 6 www.sauder.com/service 426927

å Fasten the BRACE (G) to the LEFT END (A). Use two
1-9/16" FLAT HEAD SCREWS (11)
Step 3
A
Unfinished edge
G
1-9/16" FLAT HEAD SCREW
(2 used in this step)
11
Page 7www.sauder.com/service426927

å Fasten a ROD HANGER (8) to the RIGHT END (B). Use
two 1/2" FLAT HEAD SCREWS (10).
å Fasten a METAL BRACKET (2) to the BACK SKIRT (H).
Use two 1/2" FLAT HEAD SCREWS (10).
å Insert four WOOD DOWELS (1) into the BACK SKIRT (H)
Step 4
B
8
1/2" FLAT HEAD SCREW
(4 used in this step)
10
H
2
10
1
Page 8 www.sauder.com/service 426927
(4 used)

å Push the WOOD DOWELS in the BACK SKIRT (H) to the
LEFT END (A).
å Fasten the RIGHT END (B) to the TOP/BOTTOMS (E),
SHELF (F), BRACE (G), and BACK SKIRT (H). Use eight
1-9/16" FLAT HEAD SCREWS (11)
å NOTE: Be sure the WOOD DOWELS in the BACK SKIRT
insert into the ENDS.
Step 5
B H
G
F
E
A
E
Unfinished edge
1-9/16" FLAT HEAD SCREW
(8 used in this step)
11
Page 9www.sauder.com/service426927

å Unfold the BACK (D) and lay it over your unit.
å Make equal margins along all four edges of the BACK (D).
Push on opposite corners of your unit if needed to make it
"square".
å Fasten the BACK (D) to your unit using the NAILS (4). The
NAILS should be 4" apart and 1/4" in from the edges.
Step 6
NAIL
(52 used in this step)
4
D
Unfinished
surface
8
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
4"
1/4"
Page 10 www.sauder.com/service 426927

å Carefully turn your unit over onto its back edges.
å Insert two WOOD DOWELS (1) into the ENDS (A and B).
å Fasten the BACK SKIRT (H) to the TOP/BOTTOM (E) as
shown. Use two 1/2" FLAT HEAD SCREWS (10) through
the METAL BRACKET and into the TOP/BOTTOM.
Step 7
A
B
E
1
H
1/2" FLAT HEAD SCREW
(2 used in this step)
10
Page 11www.sauder.com/service426927

å Fasten four METAL BRACKETS (2) to the FRONT SKIRT (J).
Use eight 1/2" FLAT HEAD SCREWS (10)
Step 8
J
2
1/2" FLAT HEAD SCREW
(8 used in this step)
10
2
10
2
10
Page 12 www.sauder.com/service 426927
Now might be a
good time to refresh
your drink.

å Fasten the SKIRT (J) to the ENDS (A and B).
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the SKIRT.
Step 9
J
A
B
Page 13www.sauder.com/service426927

å Fasten the SKIRT (J) to the ENDS (A and B)
and TOP/BOTTOM (E). Use eight 1/2" FLAT
HEAD SCREWS (10).
Step 10
J
1/2" FLAT HEAD SCREW
(8 used in this step)
10
A
B
E
Page 14 www.sauder.com/service 426927

å Fasten the HINGES (3) to the DOORS (C). Use twelve 1/2"
FLAT HEAD SCREWS (10).
Step 11
C
3
1/2" FLAT HEAD SCREW
(12 used in this step)
10
x2
Page 15www.sauder.com/service426927

å NOTE: It is recommended you have someone help you
with this step.
å Fasten the DOORS (C) to the ENDS (A and B). Use twelve
1/2" FLAT HEAD SCREWS (10).
Step 12
A
B
C
C
1/2" FLAT HEAD SCREW
(12 used in this step)
10
Page 16 www.sauder.com/service 426927

Step 13
å Fasten the PULLS (5) to the DOORS (C). Use four 15/16"
PAN HEAD SCREWS (12).
C
C
5
5
15/16" PAN HEAD SCREW
(4 used in this step)
12
Page 17www.sauder.com/service426927
If you're doing this to
help a friend, don't
leave without a bite.

å Carefully stand your unit upright.
å Open the FURNITURE TIPPING RESTRAINT KIT (98) and fasten the SAFETY STRAP to the TOP/BOTTOM (E). Use
the provided short screw.
å Place your unit in its final location against a wall. Locate the center of a stud in your wall near your unit and mark it
with a pencil. Next, drill a 1/8" hole on the mark and into the stud in your wall.
å Fasten the unit to the wall. Use the long screw through the other end of the strap and into the 1/8" hole.
å Peel APPLIQUES from the APPLIQUE CARD (7) and stick them onto each visible SCREW head.
å Peel the BUMPERS from the BUMPER CARD (6) onto the TOP/BOTTOMS (E) shown where they come in contact with
the DOORS (C).
Step 14
Use the short screw through the
hole in the strap and into the top
surface of the TOP/BOTTOM (E).
98
98
Electric drill with 1/8" bit
(ONLY in indicated step)
Drill 1/8" hole into
a stud in your wall.
To cover SCREWS
7
(16 used)
6
C
C
E
Page 18 www.sauder.com/service 426927

å Refer to the enlarged diagram to identify the parts on
the HINGES.
å The DOORS may need some adjustments. Follow the text
below to make needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), turn the
adjusting screw in or out.
å To adjust the DOORS up and down (vertical), remove the
round hole screws and loosen the slotted hole screws.
Move the DOORS up or down to the desired location.
Tighten the slotted hole screws first. Then turn the round
holes screws into their holes.
å To adjust the DOORS in or out (depth), loosen the
mounting screw one turn and move the DOORS in or out,
as needed. Tighten the mounting screw after
making adjustments.
Step 15 17
Page 19www.sauder.com/service426927
(vertical adjustment)
2 screws
Adjusting screw (horizontal)
Mounting screw (depth)

å Push the ROD (9) onto the ROD HANGERS (8) on the ENDS (A and B).
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Step 16
A
B
9
8
And to celebrate, why not share your success story at sauder.com or
No load
35 lbs.
50 lbs.
40 lbs.
Page 20 www.sauder.com/service 426927