Billion BiPAC 5200S Series User manual

BiPAC 5200 series
5200S, 5200, 5200G-R4, 5200G-RA, and
5200N
ADSL2/2+ Modem/Routers
UK Quick Install Guide
LAn Auto Install CD is supplied
with this product to assist with
your connection. Please ensure
you follow the instructions closely
in this guide in order to minimize
problems. This guide covers only
the initial Internet set-up. Please
refer to the full User Manual on the
CD-ROM for more advanced
settings. This guide is based on the
Billion BiPAC 5200G ADSL2/2+
Modem/Router so be aware that for
other models in the 5200 series the
screen shots will vary slightly.
www.billion.uk.com

2
QUICK INSTALL GUIDE
Billion 5200G ADSL2/2+ Modem/Router Installation
1.1 Starting out:
Before you can establish an Internet connection through your Billion 5200G
ADSL2/2+ Modem/Router make sure you have the following:
1. A Computer or Notebook with an installed Network Adaptor (sometimes called
an Ethernet Adaptor, Network Card or NIC)
2. An ADSL or DSL service account and configuration information provided by
your Internet Service Provider (ISP). You should need only a User Name and
Password, but you can check with your ISP to see if you require any of the
other following configuration parameters to connect your Billion 5200G
ADSL2/2+ Modem/Router to the Internet :
a. ISP User Name and Password
b. VPI/VCI parameters
c. Multiplexing Method
d. Host and Domain Names
e. ISP Domain Name Server ( DNS ) Address
f. Fixed or Static IPAddress.
1.2 Steps for Connection:
The following are the steps to properly connect your Billion 5200G ADSL2/2+
Modem/Router:
1. Turn off your computer.
2. If you do not have an ADSL faceplate installed by your service provider, you
must ensure ADSL splitters (also called microfilters or filters) are fitted to all
telephone sockets in use.
3. Connect the supplied ADSL RJ-11 cable from the splitter/filter of your chosen
telephone socket (or ADSL faceplate if you have one) to the ADSL Port of your
Billion 5200G ADSL2/2+ Modem/Router (or LINE Port if you have no ADSL
Port)
4. Connect the Ethernet cable (RJ-45) from one of the Ethernet ports of your Billion
5200G ADSL2/2+ Modem/Router to the Network Adaptor in your computer.
5. Connect the Power adaptor to the Billion 5200G ADSL2/2+ Modem/Router and
plug the other end into a Power outlet. Power up the unit.
6. Turn on your computer. Please allow up to 45 seconds for your Network Adaptor
to locate the Router. Please wait for the ADSL light on the front of the router to
turn from slow flashing to rapid flashing or solid – this may take up to 1 minute
(see 3.1 Troubleshooting the connection).

3
7. You are now ready to configure the Billion 5200G ADSL2/2+ Modem/Router.
8. Please insert the supplied Configuration Utility CD into your computer’s
CD/DVD drive now, and follow the simple on-screen instructions to connect your
Billion 5200G ADSL2/2+ Modem/Router. This process may take up to 5 minutes.
All you need to do is to follow the instructions on screen and when prompted
enter your User Name and Password as supplied by your Service Provider and
set up your wireless security as required. No other changes should be necessary.
9. You should now be connected to your Service Provider. This completes the initial
connection and wireless configuration of the modem.
10. If you have not been supplied with a Configuration Utility CD or the supplied
CD is not working, please configure your Router manually by following the
instructions for Manual Configuration in section 2.1.
2.1 Manual Configuration:
1. Open Internet Explorer or your default web browser and type
http://192.168.1.254 on the address bar (where you would normally enter the
web site address) as per the illustration below.
2. You will be presented with a user name and password prompt.* Simply enter
user name as admin, password as admin and click OK.

4
* If the user name and password prompt box does not appear make sure
that any firewall or anti-virus such as Trend Micro or Norton is disabled.
Also ensure that your Internet settings are correct. (In Internet Explorer go
to Tools/Internet Options/Connections and make sure “Never dial a
Connection” is checked. Then Click on the LAN settings and ensure
“Automatically detect settings” is checked and all other fields are blank.
Then go to Tools/Internet Options/Security and return your Security
settings to “default”. )
3. This will take you to the modem’s Home Page and will show the modem’s
Status.
4. Click on Interface Setup to access the manual configuration fields. Under the
heading ATM VC ensure the Virtual Circuit is PVC0, Status is Activated, the
VPI setting is 0 and the VCI setting is 38. Under the heading Encapsulation
make sure PPPoE/PPPoA is checked.*
* Standard UK settings are VPI 0, VCI 38 and Encapsulation PPPoA VC-
Mux. A small number of Service Providers do however have their own
proprietary settings. In this case please contact your Service Provider to
confirm their configuration parameters.

5
5. Under the heading PPPoE/PPPoA enter your User Name and Password as
supplied by your Service Provider and check the Encapsulation is PPPoA VC-
Mux.
6. Click the Save button at the bottom of the page.

6
7. After the settings are saved you should be connected to you Service Provider.
8. Under Interface Setup you can click on Wireless should you wish to access
the advanced wireless configuration fields.
9. Confirm any changes you make to your wireless settings by clicking Save.
10. For further advanced configuration please access the full manual on the CD
provided.
3.1 Troubleshooting the connection:
1. Check that the ADSL light on the front of the router has turned to rapid
flashing or solid. This can take up to 1 minute after switching on. (If the
ADSL light continues to flash slowly then the router is not detecting an ADSL
signal and you should contact your Service Provider immediately)
2. Ensure your username and password are correct – your username should read
[email protected] (or something similar).
3. Ensure you have a filter attached to the master socket, and check there are no
phones connected to any extensions that do not have a filter.
If you still can’t get a connection after checking the above – disconnect all phones,
sky boxes, fax machines etc., double–check that all cables are correctly connected and
filters properly attached, restart the router, and try again.
If this still fails then we suggest you contact your Service Provider for further advice.

7
Telephone Support for Internet Access ONLY is available during office hours from
Mon-Fri 10am–5pm on 0870-8501528. If you are successfully connected to the
Internet and have a support query please visit www.billion.uk.com/esupport and
submit a ticket.
This symbol on the product or in the instructions means that your electrical and electronic
equipment should be disposed at the end of its life separately from your household waste.
There are separate collection systems for recycling in the EU.
For more information, please contact the local authority or your retailer where you purchased
the product.