Billion BiPAC 4700ZU User manual

BiPAC 4700ZU(L)
4G LTE Outdoor (VPN) Router
* Only BiPAC 4700ZU support VPN feature
Quick Start Guide

BiPAC 4700ZU(L) 4G/LTE Outdoor (VPN) Router
1
Package Contents
 BiPAC 4700ZU(L)
4G/LTE Outdoor (VPN)
Router
 M25 Cable Gland
 This Quick Installation
Guide
 Outdoor LAN Cable
 Gigabit Power-over-
Ethernet (PoE) Injector
 Grounding Wire
 Mounting Kit
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS
CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE
DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE
INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO
THE ON-LINE USER MANUAL.
 Please follow Router Installation Instructions to power on your ODU,
Never disassemble or modify this product, tampering with this product
may result in WARRANTY VOID.
 This equipment should be installed and operated with minimum distance
20cm away from your body.

Quick Start Guide
2
Hardware Overview
LED Description:
CONNECTORS DESCRIPTION
SIM / LED / Reset
Insert the SIM card into the SIM slot.
Press the reset button to reset device or restore to factory default settings.
Gigabit LAN(PoE)
Connect with the supplied PoE injector, 802.3at compliant, using an Ethernet
cable.
LED STATUS DESCRIPTION
Orange System is either in initial startup phase or has boot failure
Green System is up and ready
1 Power
Off No input power
Green Transmission speed is at Gigabit speed (1000Mbps)
Orange Transmission speed is at 10/100Mbps
Blinking Data being transmitted/received
2 LAN(PoE)
Off No device is being connected
Green IP connected and traffic is passing thru the device
3 Internet
Orange IP request failed or System is in initial booting phase
Green RSSI greater than -69 dBm. Excellent signal condition
Green
Flashing quickly
RSSI from -81 to -69 dBm. Good signal condition
Orange
Flashing quickly
RSSI from -99 to -81 dBm. Fair signal condition.
Orange
Flashing slowly RSSI less than -99 dBm. Poor signal condition.
Orange No signal. 4G_LTE module is still in connected mode
4
3G/4G-LTE
(Received
Signal
Strength
Indicator)
Off No LTE module or LTE module fails
1 2 3
4

BiPAC 4700ZU(L) 4G/LTE Outdoor (VPN) Router
3
Mounting Kit Installation
1. Attach the Articulation Pole to the Enclosure
Attach the articulation pole to the back of the BiPAC 4700ZU(L) enclosure using the supplied
M6 screws, M6 spring washers and M6x16 screws which are included in the mounting kit.
Step 1:
Step 2:
Step 3: Use Wrench to tighten or loosen the bolt(s).

Quick Start Guide
4
2. Wall or Pole Mounting
2.1 Mounting on Wall
Fix the T-formed Bracket to the wall by using wood screws and Gyprock plugs.
2.2 Mounting on a Pole
2.2.1 Mounting for pole 1.5” (38mm) to 3”(80mm)
Attach the T-formed Bracket and the W-bar to the pole then use M6x60 bolts, M6 spring
washers and M6 washers to fix the mounting kit onto the pole.
2.2.2 Mounting for pole 3” (80mm) or above

BiPAC 4700ZU(L) 4G/LTE Outdoor (VPN) Router
5
3. Install the Articulation Pole with the T-formed Bracket
Attach the articulation pole (BiPAC 4700ZU(L) enclosure) to the T-formed bracket using the
supplied M8 nut, M8 spring washer, M8 washer and M8x40 screw bolts.
4. Position Adjustment
Find the location and best angle for getting the strongest signal from the base station. The
BiPAC 4700ZU(L) must be directed towards the nearest base station.
Adjusting the router position to get a better reception and/or fine-tuning the router orientation
(45-degree angle position or in horizontal/vertical position) to have the best signal strength.

Quick Start Guide
6
Router Installation Instructions
1. Grounding the BiPAC 4700ZU(L) to Complete the Installation
Attach the grounding wire to the BiPAC 4700ZU(L) and tighten the screw
2. Power on your BiPAC 4700ZU(L)
Step 1: Assemble M25 cable gland. Unscrew the LAN (PoE) port and insert the supplied
outdoor Ethernet cable (RJ-45) through material A-D, and then connect the RJ-45 Ethernet
cable into the LAN (PoE) port.
Step 2:
3.1: Insert
○
C at the back end of
○
D
3.2: clip
○
B on
○
C
3.3: keep
○
B close to
○
D
3.4: then tighten
○
A .

BiPAC 4700ZU(L) 4G/LTE Outdoor (VPN) Router
7
It is recommended to use an Industrial-grade SIM card.
MUST use a Mini-SIM (2FF) Card with dimensions of 25x15x0.76mm.
Step 3: Insert the other end of outdoor Ethernet cable (RJ-45) to the supplied Gigabit PoE
injector Data+Power port. Connect another Ethernet cable (RJ-45) directly to the Data port
and the other end of cable to a switch or broadband router.
IMPORTANT: It is recommended to put the Gigabit PoE Injector on an UPS or Surge
Protector. Use the supplied grounding wire to ground your BiPAC 4700ZU(L) ODU is
REQUIRED!
3. Set up your 4G/LTE Internet Connection
Step 1: Unscrew the cap of SIM card slot.
Step 2: Slide the SIM card with the mental
contacts (gold plate) facing down to the SIM
slot then push it all the way in until you hear
the clicking sound.

Quick Start Guide
8
Step 3: Screw the cap back tightly.
NOTE: Please power off the device before
inserting or removing the SIM card.
Step 4: Login to your BiPAC 4700ZU(L)
The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the
attached PC to this router is in the same subnet and has an IP address in the range between
192.168.1.1 ~ 192.168.1.253.
Open a web browser and type http://192.168.1.254 in the URL address bar.
The login prompt will appear. Input the default username (admin) and password (admin) for
Account type, Administrator. <*This username / password may vary by different Internet Service
Providers.>
Please see the relevant sections of user manual for detailed instructions on how to
configure your BiPAC 4700ZU(L).
Step 5: Use the Quick Start wizard for fast Internet connection setups.
4.1 Change administration password: Setup a new password for “admin” account for device
management. The default password is “admin”. Click Continue to go on to the next step.
*The password may vary by different Internet Service Providers.
4.2 Time Zone Configuration: Enable and select your Time Zone then click Continue to go on
to the next step
URL Address bar:
type
http://192.168.1.254
New Password:
assign a new,
unique password
Confirm Password: re-
enter the
new password again
Next Step: click Next
Time Zone:
select your time zone
Next Step: click Next