Billion BiPAC 8501 User manual

BiPAC 8501
SHDSL.bis VPN Firewall Bridge/Router
Quick Start Guide

SHDSL.bis VPN Firewall Bridge/Router
1
For more detailed instructions on con
f
i
g
urin
g
and usin
g
th
e
Billion SHDSL.bis VPN Firewall Bridge/Router, please re
f
er to
the on-line manual.
Package Contents
SHDSL.bis VPN Firewall Bridge/Router
CD-ROM containing the online manual
RJ-11 SHDSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
Console (PS2-RS232) Cable
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
 Do not use this router in high humidity or high temperatures.
 Do not use the same power source for this router as othe
r
equipment.
 Do not open or repair the case yourself. If this router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Warning  Avoid using this product and all accessories outdoors.
 Place this router on a stable surface.
 Only use th
differ e power adapter that comes with the package. Using a ent voltage rating power adaptor may damage this router.
A
ttention

Quick Start Guide
The Front LEDs
2
3
1
24
LED Meaning
1 PWR Lit when power is ON.
2 SYS Lit when the system is ready.
3 Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps.
LAN Port
1X — 4X
(RJ-45 connector) Blinking when data is Transmitted / Received.
4 LINE Lit when successfully connected to SHDSL line and it is
synchronized.

SHDSL.bis VPN Firewall Bridge/Router
The Rear Ports
3
5 1
3
6 2
4
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 RESET
After the device is powered on, press it to reset the
device or restore to factory default settings.
1-3 seconds: reset the device
6 seconds above, and power off, power on the device:
restore to factory default settings (this is used when you
can not login to the router, e.g. forgot the password)
4 LAN 1X — 4X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of
the four LAN ports when connecting to a PC or an
office/home network of 10Mbps or 100Mbps.
5 CONSOLE Connect a PS2/RS-232 cable to this port when
connecting to a PC’s RS-232 port (9-pin serial port).
6 LINE Connect the supplied RJ-11 (“telephone”) cable to this
port when connecting to the A SHDSL line.

Quick Start Guide
Connecting Your SHDSL Bridge/Router
1. Connect the Router to a LAN (Local Area Network) and the SHDSL LINE.
2. Power on the device.
4
3. Make sure the PWR and SYS LEDs are lit steadily and that the relevant LAN and LINE LED
are lit.

SHDSL.bis VPN Firewall Bridge/Router
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
5

Quick Start Guide
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
6

SHDSL.bis VPN Firewall Bridge/Router
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In
the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and
click OK to finish the configuration.
7

Quick Start Guide
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
8