Bin Master BINCLOUD BCGW.02LLC-DPM500 User manual

Tools needed: drill and bit, phillips screwdriver, drywall/
wood screws, ethernet cable, pliers. Screws and plas-
tic plugs,A1, can be used to secure the top cover.
STEP 2
Attach mount brackets to the enclosure
with the included screws. Brackets t on
protruding screwholes on the back of
the enclosure. Then, use drywall screws
and attach unit to the wall location.
A1
QUICK SETUP GUIDE
BINCLOUD GATEWAY
BCGW.02LLC-DPM500
laser
sensor
Control
room
1
3
2
4
power
ethernet
STEP 1
Choose a location to mount your Gateway and the antenna. For the Gateway,
make sure there is access to a 120VAC outlet. The antenna should be in a good
line-of-sight to sensors within 20 feet of the Gateway location.
1. Gateway (with cellular antenna, ethernet also an option)
2. Wire through wall to antenna
3.Antenna mounted outside with line of site to sensor (wired to Gateway)
4. Sensor mounted on vessel

STEP 3
Assemble the antenna with mounting hardware. A.
B.
C.
x. y.
washer-locking washer-nut-bolt
STEP 5
A. Connect antenna wire to the top of the Gateway unit.
B. Connect antenna wire to bottom of antenna.
C. Plug Gateway into a 120V outlet.
D.Attach the antenna as shown. This Gateway has been setup with multiNetwork cell connection that will automatically connect when
powered. If cell service is unavailable it is possible to connect the Gateway ethernet plug to a network router or switch.
WAY TO GO!
Wait 25 minutes and call BinMaster at 1-800-278-4241 to conrm the internet connection. BinMaster will create a custom cloud page
using measurements from your bins, tanks, silos, etc. Check the worksheet on following pages so you can prepare for this conversation.
A. B. C.
STEP 4
1. Open the Gateway cover and nd the
4-20mAadapter terminal.
2.Connect the Gateway +24VDC” to
DPM500 mA+(6)
3.Connect Gateway “INPUT” to
DPM500 COM(5)
4.Connect Gateway +24VDC to sensor D0(+)
5.Connect Gateway GND to sensor D1(-) Gateway
D.
A.Attach the curved mount pipe to its base
with the smooth bolt on top and two small
bolts and nuts on the swivel bottom.
B. Using U-bolts as shown attach antenna
mount to mount pipe (x). Then insert small
screws on top of mount to hold antenna in
place (y).
C. Mount the antenna outside, in a location
(Step 1) within a good line-of-sight to your
sensor(s) . Remember the cable between
the Gateway unit and the antenna should
be less than 20 feet or ask your BinMaster
rep for an extension.
4-20mA
sensor
DPM 500

FIREWALLRULES FOR BINCLOUD GATEWAY
Direction Outbound Ports For these IPS IPAddresses
TCP 80, 433 All
UDP 5959-5961 52.38.107.102
5959-5961 52.25.64.249
5959-5961 34.221.219.221
5959-5961 54.218.6.237
UDP 5959-5970 52.39.255.60
54.71.174.229
52.88.4.160
34.217.159.41
34.213.84.184
52.43.176.61
35.162.54.59
52.42.122.172
44.224.165.129
44.226.176.44
44.237.66.197
44.238.4.218
54.184.44.101
44.228.115.25
44.230.239.2
44.236.20.68
44.236.200.9
44.236.76.190
44.239.243.92
44.240.35.27
Direction Outbound Ports Region IPAddresses
UDP 20000-40000 USA All
UDP 54.212.116.92
UDP 52.12.114.120
UDP 52.87.228.243
UDP 3.88.21.119
UDP 34.223.7.202
UDP Europe 54.93.100.223
UDP 18.195.88.21
UDP 18.184.70.5
UDP India 15.207.116.15
UDP 13.127.230.228
UDP SEAsia 13.212.70.205
UDP 13.212.30.222
UDP Asia 18.182.42.125
UDP 13.230.250.171
UDP 18.179.34.24
UDP Japan 52.69.206.76
UDP 18.179.57.238
Wiring for a 2-wire sensor,
powered by the current loop
4-20mA
sensor
Wiring for a 3-wire sensor,
powered by Yocto-4-20mA-Rx
(max 80mA)
4-20mA
sensor
Wiring for a 4-wire sensor, with an
independent power supply
4-20mA
sensor
Power
source
4-20mA
sensor
Power
source
Wiring for 3-wire sensor, with
independent power supply with
common ground
Supplemental info about 4-20mAto USB adapter installed inside the BinCloud Gateway