Binary B-660-EXT-444-40 User manual

Source | Mute | 2ch
(HDMI Out Audio)
INSTALLATION
MANUAL
4K HDR HDBaseT Extender with IR & RS-232
B-660-EXT-444-40

2

3
1. IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of re or electric shock, read and follow all instructions and warnings in this
manual. Keep this manual for future reference.
2. Do not expose this apparatus to rain or moisture. Do not expose this equipment to dripping
or splashing, and ensure that no objects lled with liquids, such as vases, are placed on the
equipment. Do not use this apparatus near water.
3. Do not remove cover. No user serviceable parts inside.
4. Clean only with a dry cloth.
5. Do not block any ventilation openings. Install according to manufacturer’s instructions.
6. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including ampliers) that produce heat.
7. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has
two blades, one of which is wider than the other. A grounding plug has two matching blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
8. Protect the power cord from being walked on or pinched, particularly at the plug end and
where the power cord is attached to the apparatus.
9. Only use attachments and accessories specied by the manufacturer.
10. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power supply cord or plug is damaged,
liquid has been spilled on or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, the apparatus does not operate normally, or it has been
dropped.
11. To completely disconnect this equipment from power, disconnect the power supply cord
from the power outlet.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTIRCAL SHOCK DO NOT
REMOVE COVER.
NO USER SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

4
FCC WARNINGS
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

5
1. CONTENTS
1. Product Overview ....................................................................................................................................................6
2. Features ......................................................................................................................................................................6
3. Package Contents ......................................................................................................................................................6
4. Device Layout ..............................................................................................................................................................7
5. Installation & Wiring ................................................................................................................................................11
5.1 Wiring .....................................................................................................................................................................11
6. EDID DIP Switch ........................................................................................................................................................13
7. Function DIP Switch .................................................................................................................................................14
8. RS-232 Passthrough .................................................................................................................................................15
9. Specications ..............................................................................................................................................................16
10. Transmission Distance .............................................................................................................................................17
11. Warranty ......................................................................................................................................................................18
12. Support ......................................................................................................................................................................18

6
1. PRODUCT OVERVIEW
B-660-EXT-444-40 is a 4K HDMI extender with 4K@60Hz 4:4:4 8bit including DCI 4K
(4096 x 2160), and HDCP 2.2 compatibility. It can transmit 1080P signals up to 60m/197ft
and 4K@60Hz signals up to 35m/115ft via Cat 5e/6 cable, and transmit 1080P signals up to
70m/230ft and 4K@60Hz signals up to 40m/131ft via Cat 6a/7 cable,
B-660-EXT-444-40 supports bi-directional IR pass through, CEC pass through and RS-232 pass
through. With bi-directional PoC supported, only one power adapter is needed. It offers the
added benet of an incredibly low-prole for a greatly reduced form factor behind the screen
for even more convenience and ease of installation at the display zone.
Two independent 4-pin Video and Audio EDID DIP Switches can provide varieties of EDID
combinations to t the needs of installation and operation environment. 4-pin Function DIP
Switch can provide a variety of congurations and upgrading requirements to t the multiple
different application scenarios.
2. FEATURES
• Supports resolutions up to 4K@60Hz 4:4:4 8bit and HDCP 2.2.
• Supports HDR (High Dynamic Range), including HDR 10, HDR 10+, HLG and Dolby Vision
(only up to 4K@30Hz).
• Over a Cat 5e/6 cable, HDBT transmits 4K@60Hz 4:4:4 8bit up to 35m/115ft, and 1080P up
to 60m/200ft; Over a Cat 6a/7 cable, HDBT transmits 4K@60Hz 4:4:4 8bit up to 40m/130ft,
and 1080P up to 70m/230ft.
• Supports DIP Switches to congure EDID, IR and RS-232 functions.
• Supports CEC pass through.
• Supports bi-directional IR pass-through and RS-232 pass through
• Bi-directional PoC, one power adapter at either transmitter or receiver side can power both
units.
3. PACKAGE CONTENTS
• 1 x B-660-EXT-444-40 Extender
• 1 x DC 18V Power Adapter with US Pins
• 4 x Mounting Brackets (with Screws)
• 4 x Drywall Screws
• 8 x Rubber Feet
• 2 x HDBaseT Sticker
• 2 x Power Cord Sticker

7
4. DEVICE LAYOUT
4.1. B-660-EXT-444-40 Transmitter
FIGURE 1: Transmitter Layout
1. POWER LED
On/Off: The transmitter is powered on/off.
2. STATUS LED
Blinking: The transmitter is working properly.
Off: The transmitter is not working properly.
3. LINK LED
On: HDBT link is normal.
Off: No HDBT link.
4. HDCP LED
On: HDCP signal is being transmitted.
Blinking: No-HDCP signal is being transmitted.
Off: No signal is being transmitted.
5. VIDEO
Video EDID DIP Switch. More information, see
EDID DIP Switch Section.
6. AUDIO
Audio EDID DIP Switch. More information, see
EDID DIP Switch Section.
7. FUNCTION
Function DIP Switch. More information, see Function DIP Switch Section.

8
4.2. B-660-EXT-444-40 Transmitter
FIGURE 2: Transmitter Layout
1. +18V DC
Connect the 18V power cord provided.
2. HDBT OUT
Connect to the receiver via a Cat x cable.
3. IR Receiver
Connect to an IR receiver cable.
4. IR Flasher
Connect to an IR emitter cable.
5. RS-232
RJ45 port. Connect to a RS-232 control device such as a PC for RS-232 pass through or
rmware upgrade.
6. HDMI IN
Connect to an HDMI source device.

9
4.3. B-660-EXT-444-40 Receiver
FIGURE 3: Receiver Layout
1. POWER LED
On/Off: The transmitter is powered on/off.
2. STATUS LED
Blinking: The transmitter is working properly.
Off: The transmitter is not working properly.
3. LINK LED
On: HDBT link is normal.
Off: No HDBT link.
4. HDCP LED
On: HDCP signal is being received.
Blinking: No-HDCP signal is being received.
Off: No signal is being received.
5. FUNCTION
Function DIP Switch. More information, see Function DIP Switch Section.

10
4.4. B-660-EXT-444-40 Receiver
FIGURE 4: Receiver Layout
1. +18V DC
Connect the 18V power cord provided.
2. HDBT IN
Connect to the transmitter via a Category cable.
3. IR Receiver
Connect to an IR receiver cable.
4. IR Flasher
Connect to an IR emitter cable.
5. RS-232
RJ45 port. Connect to a RS-232 control device such as a PC for RS-232 pass through or
rmware upgrade.
6. HDMI OUT
Connect to an HDMI display.

11
5. INSTALLATION & WIRING
Installation
B-660-EXT-444-40 can be placed on a solid and stable surface or installed on a standard
equipment rack.
Steps to install the matrix on an equipment rack:
1. Attach the installation bracket to the enclosure using the screws provided in the package
separately.
2. The bracket is attached to the enclosure as shown.
3. Repeat steps 1-2 for the other side of the transmitter.
4. Mount and afx the transmitter in the rack mount with the mounting screws.
5. Repeat steps 1-4 to install the receiver.
5.1 Wiring
Warnings:
• Before wiring, disconnect the power from all devices.
• During wiring, connect and disconnect the cables gently.
Steps for device wiring:
1. Connect HDMI IN
Connect the HDMI sources (such as PC, Blu-ray player, Apple TV, 4K media player, etc) to
the HDMI IN of the transmitter.
2. Connect HDBT OUT
Connect HDBT OUT of the transmitter to HDBT IN of the receiver with Cat 5e/6/7 cables.
3. Connect HDMI OUT
Connect HDMI display device (such as TV, projector, LED/LCD display) to the HDMI OUT of
the receiver.
4. Connect for additional control options:
• IR Pass Through: Connect IR emitter cable to IR Flasher port or IR receiver cable to
IR Receiver port of the transmitter, and connect IR receiver cable to IR Receiver port
or IR emitter cable to IR Flasher port of the receiver. The source remote can control
the source on the receiver side or the display remote can control the display on the
transmitter side.

12
• RS-232 Pass Through: Set pin2 of Function DIP Switch to select RS-232 connection
mode, and ensure the Pin3 and Pin4 of Function DIP Switch are set to “0” position
simultaneously (see “Function DIP Switch” Section), connect control devices such as
PC to RS-232 ports of transmitter and receiver to realize RS-232 pass through (More
information, see RS-232 Pass Through section).
5. Connect the DC 18V power cord provided.
6. Power on all attached devices.

13
6. EDID DIP SWITCH
EDID is congured by Video and Audio DIP Switch. The default setting is Auto, please referring
to the following table to congure.
Video DIP Switch Position
EDID Resolution 1 2 3 4
0Auto (Default) Up Up Up Up
1 1080P SDR Up Up Up Down
2 1080P HDR Up Up Down Up
3 4K@30 SDR Up Up Down Down
4 4K@30 HDR Up Down Up Up
54K@60 4:2:0 SDR Up Down Up Down
6 4K@60 HDR Up Down Down Down
Audio DIP Switch Position
EDID Resolution 1 2 3 4
0Auto (Default) Up Up Up Up
12CH (PCM) Up Up Up Down
2 6CH Up Up Down Up
3 8CH Up Up Down Down

14
7. FUNCTION DIP SWITCH
IR and RS-232 functions can be congured by Function DIP Switch. The default setting is
“0000” (Up, Up, Up, Up), please refer to the following table to congure.
4-Pin Up:0, Down: 1
1 2 3 4 Function
0/1 - - - 0: IR 12V off;
1: IR 12V on
-0/1 - - 0: DTE (RS-232)
1: DCE (RS-232)
- - 0/1 -00: Normal (RS-232)
10: System FW update
01: HDBT FW update
11: Reserved
- - - 0/1
Pin1 is set to “0”, IR Receiver port can not supply 12V power outward, when set to “1”, IR
Receiver port can supply 12V power outward. Transmitter and receiver are congured
separately.
Pin2 is set to “0”, RS-232 serial DTE mode. Pin2 is set to “1”, RS-232 serial DCE mode. Set the
connection mode according to the devices used. Transmitter and receiver are congured
separately.
Pin3 and Pin4 are set to “0” simultaneously, RS-232 port realizes the function of pass through.
Pin3 and Pin4 are set to “10”, connect to a PC to upgrade ST/BV6336 chip. Pin3 and Pin4 are
set to “01”, use Valens tool to upgrade Valens chip.

15
8. RS-232 PASSTHROUGH
RS-232 ports can be used for bi-directional RS-232 signal pass through between the
transmitter and receiver.
Set pin2 of Function DIP Switch to “0” or “1” to select RS-232 connection mode (DTE or DCE),
set pin3 and pin4 of Function DIP Switch to “00” (see Function DIP Switch section), connect
RS-232 control devices (such as PC) to RS-232 ports of transmitter and receiver. See the below
picture:
Note: If the selected RS-232 connection mode is not enabled, please set to another mode.

16
9. SPECIFICATIONS
Technical
Input/Output Port
Transmitter:
1 x HDMI IN, 1 x HDBT OUT, 1 x IR Receiver,
1 x IR Flasher, 1 x RS-232 (RJ45),
1 x DC 18V IN
Receiver:
1 x HDMI OUT, 1 x HDBT IN, 1 x IR Receiver,
1 x IR Flasher, 1 x RS-232 (RJ45),
1 x DC 18V IN
Input/Output Signal Type HDMI with 4K@60Hz YUV 4:4:4, HDCP 2.2,
including DCI 4K (4090x2160)
Input/Output Resolution Supported
VESA:
800x6008, 1024x7688, 1280x7688,
1280x8008, 1280x9608, 1280x10248,
1360x7688, 1366x7688, 1440x9008,
1600x9008, 1600x12008, 1680x10508,
1920x12008, 2560x14408, 2560x16008
SMPTE:
1280x720P6,7,8, 1080I6,7,8,
1920x1080P1,2,3,4,5,6,7,8,
3840x2160P2,3,5,6,8, 4096x2160P2,3,5,6,8
1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 =
at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at
59.94 Hz, 8 = 60 Hz, 9 = 75 Hz
Audio Format
HDMI IN/OUT: Fully supports audio formats
in HDMI 2.0 specication, including PCM
2.0/5.1/7.1, Dolby TrueHD, Dolby Atmos,
DTS-HD Master Audio and DTS:X
Maximum Data Rate HDMI IN & HDMI OUT: 18Gbps
Control Method IR, RS-232, CEC, DIP Switches
General
Operating Temperature -10°C to 50°C/263°F to 323°F (Indoor)
-20°C to 60°C/253°F to 333°F (Outdoor)
Storage Temperature -20°C to 70°C (-4°F to 158°F)
Humidity 10% to 90%, non-condensing
ESD Protection Human-body Model:
±15kV (Air-gap discharge)
Power Supply DC 18V 1.3A
Power Consumption (Max)
Receiver is powered by transmitter: 16.47W
Transmitter is powered by receiver: 14.55W
Transmitter and receiver are powered
separately: Transmitter: 5.71W,
Receiver: 8.46W

17
General
Device Dimension
(W x H x D)
142mm x 15.4mm x 85mm/5.59” x 0.61” x
3.35”
(Without mounting brackets)
Product Weight 0.32kg/0.71lb
9.1Transmission Distance
Note: Straight-through category cable wired to T568B standard is recommended.
Cable Type Range Supported Video
Cat 5e/6 60m/200ft Up to 1080P@60Hz 36bpp
Cat 6a/7 70m/230ft
Cat 5e/6 35m/115ft 1080P@60Hz 48bpp
4K@30Hz 24bpp
4K@60 4:2:0 24bpp
4K@60 4:4:4 24bpp
Cat 6a/7 40m/130ft
HDMI
Input/Output:
15m/50ft 1080P@60Hz 24bpp
Input: 5m/16ft
Output: 10m/33ft
4K@30Hz 4:4:4 24bpp
4K@60Hz 4:2:0 24bpp
Input: 3m/10ft
Output: 10m/33ft 4K@60Hz 4:4:4 24bpp

18
10. WARRANTY
Find details of the product’s Limited Warranty and other safety, patent, and legal resources at
snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
11. SUPPORT
For chat and telephone, visit tech.control4.com/s/contactsupport
• Email: T[email protected] • Visit tech.control4.com for discussions, instructional
videos, news, and more.

19

200-B-660-EXT-444-40-B
Copyright ©2021, Snap One, LLC. All rights reserved. Snap One and its respective logos are
registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home
Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4
My Home, SnapAV, Araknis Networks, BakPak, Binary, Dragony, Episode, Luma, Mockupancy,
Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox,
SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE
are also registered trademarks or trademarks of Snap One, LLC. Other names and brands
may be claimed as the property of their respective owners. Snap One makes no claim that the
information contained herein covers all installation scenarios and contingencies, or product use
risks. Information within this specication subject to change without notice.