Binks 7/15 PSP User manual

Instruction Manual
Maple 7/15 PSP
Model 10 41 47

Instruction Manual
Page 2 of 16 Issue: 1.1

Instruction Manual
Page 3 of 16 Issue: 1.1
Specification
Pump Ratio 15:1
Max. Air Pressure Inlet 7 Bar
Max. Fluid Pressure 105 Bar
Nominal Flow Volume / Cycle 0.166 Litres
0.044 US Gall
Fluid Output @ 60 cycles/min 10.0 Litres / min
2.6 US Gall / min
Maximum Recommended Continuous Cycle Rate
Maximum Recommended Intermittent Cycle Rate
20 Cycles /min
40 Cycles /min
Fluid Connections
Inlet
Outlet
1” Sanitary
½” NPT Female
Compressed Air Inlet
3/8” BSPP / NPSM
Air Volume / cycle
0.33 SCFM (9.5 L/m) @ 45PSI (3.1 Bar)
0.65 SCFM (18.5 L/m) @ 90 PSI (6.2 Bar)
Air Flow @ 15 cycles/min 6 bar
Air Flow @ 30 cycles/min 6 bar
10 CFM (283 L/min)
20 CFM (566 L/min)
Max. Pump Inlet Pressure 2 Bar (30 PSI)
Air Quality ISO 8573.1 Class 3.3.2 # (See Note)
Dirt 5 microns
Water -20ºC@7bar (940ppm)
Oil 0.1mg/m³
Total Weight of Pump 30 Kg / 66 lbs
# Note: Class 3.4.2 Air Quality (Refrigerant dried - water + 3ºC@7bar) may be used,
however, above 15 cycles/min optional heavy duty mufflers 192821 or piped exhaust
system should be used, if used continuously.

Instruction Manual
Page 4 of 16 Issue: 1.1

Instruction Manual
Page 5 of 16 Issue: 1.1

Instruction Manual
Page 6 of 16 Issue: 1.1
KEY
= GREASE (AGMD
-
010)
= LOCTITE = TORQUE = GREASE INTERNAL (AGMD-010) = MAINTENANCE ORDER (REVERSE FOR ASSY)
= MAGNET HAZARD
ITEM 6
DETAIL

Instruction Manual
Page 7 of 16 Issue: 1.1
Parts List – 104147
ITEM PART No DESCRIPTION QTY REMARKS
1 0115-010102 AIR VALVE ASSEMBLY 1
2 161992 Ø117.5 x 2.62 VITON O-RING 2

3 161993 Ø20.35 x 1.78 VITON O-RING 2

4 161994 Ø4.47 x 1.78 O'RING 4

5 161995 Ø19.5 x 3.00 O-RING 2

6 162703 SHA T SEAL 2

7 162704 SHA T BEARING 2

8 162746 Ø25.5 X 2.00 O'RING PT E 2

9 163920 M6 x 30 CAP HD SCREW (ST ST) 4
10 164838 No 2 x 4.75 RIVET 2
11 165044 M12 SPRING WASHER STST 8
12 165108 M8 SPRING WASHER 16
13 165123 Ø10 SPRING WASHER (STST) 8
14 165135 M10 PLAIN WASHER (ST ST) 4
15 165528 M4 x 16 CAP HD SCREW (STST) 4
16 165948 M10 x 40 CAP HD SCREW (ST ST) 8
17 165963 M8 DOME NUT 16
18 165965 M10 x 16 HEX HEAD SET SCREW (STST) 4
19 165970 M4 PLAIN WASHER (STST) 4
20 165971 Ø4 SPRING WASHER (STST) 4
21 171792 3/4 BALL 440C 2

22 177009 M12 X 35 CAPHEAD SCREW 8
23 192009 1 & 1 1/2 SANITARY CLAMP 2
24 192147 NAMEPLATE 1
25 192206 1 SANITARY GASKET PT E 2

26 192374 RETAINING NUT 2
27 192579 KNI ED BELLOWS 2

28 192757 MAPLE CYLINDER 1
29 192758 END PLATE 2
30 192761 CYLINDER STUD 6
31 192762 CYLINDER STUD LONG 2
32 192763 BELLOWS SPACER 2
33 192764 PUMP BRACKET 2
34 192765 PILOT SPOOL ASSY 2 #
192773 PILOT SPOOL O’RING 6
 -NOT SHOWN
35 192777 1" MU LER 2
36 192799 VENT PLUG 2
37 192812 EXHAUST ADAPTER 1
38 192814 BELLOWS LEAK HOSE 1

39 192815 1/8R - 6MM PUSH IN ELBOW 2

40 194286 OUTLET SEAT 2
41 193225 OUTLET CYLINDER 2
42 193357 PISTON ASSEMBLY 2
43 193360 INLET MANI OLD 1
44 193361 INLET CYLINDER 2
45 193367 OUTLET CHECK 2
46 193419 OUTLET MANI OLD ASSEMBLY 1
47 193195 PISTON SEAL 2
# 
48 194293 AIR MOTOR PISTON ASSEMBLY 1

Instruction Manual
Page 8 of 16 Issue: 1.1
Item 48 – 194293 Air Piston Detail
ITEM PART No DESCRIPTION QTY REMARKS
50 162702 PISTON SEAL 1 
51 165964 M12 x 40 GRUBSCREW (ST ST) 1
52 192759 PISTON SHA T 2
53 192760 PISTON 1
= GREASE (AGMD-010)
= LOCTITE
= TORQUE
= GREASE INTERNAL (AGMD-010)
= MAINTENANCE ORDER
(REVERSE FOR ASSY)
KEY

Instruction Manual
Page 9 of 16 Issue: 1.1
Item 42 - 194292 Piston Assembly
ITEM PART No DESCRIPTION QTY REMARKS
60 160526 CONICAL SPRING 1 
61 162743 Ø33 X 2 'O' RING PT E 1

62 162744 Ø23.52 X 1.78 ORING PT E 1

63 162745 Ø29.9 X 1.78 O'RING PT E 1 
64 171793 0.875 BALL 1

65 193188 INLET SPRING KEEP 1

66 194287 PISTON SEAT 1
67 193358 Ø46 PISTON 1
68 193359 PISTON KEEP 1
= GREASE (AGMD-010)
= LOCTITE
= TORQUE
= GREASE INTERNAL (AGMD-010)
= MAINTENANCE ORDER
(REVERSE FOR ASSY)
KEY

Instruction Manual
Page 10 of 16 Issue: 1.1
Item 1 - 0115-010102 Valve Assembly
ITEM PART No DESCRIPTION QTY REMARKS
80 0115-010015 SPOOL AND SLEEVE ASSEMBLY 1 #
162789 SPOOL AND SLEEVE O’RING 6  Not Shown
81 0115-010016 BUMPER 2 
82 0115-010017 MAGNET 2
83 0115-010018 VALVE BLOCK END CAP 2
84 0115-010020 DIAPHRAGM 2 
85 0115-010021 O-RING 1.5 X 36 2 
86 0115-010049 O-RING 2 x 20 2

87 0115-010073 M4 x 12 SHCS 8
88 0115-010097 VALVE BLOCK 1
89 0115-010103 1/4 BSPT PIPE PLUG 1
90 0115-010107 1/8 BSPT PIPE PLUG 1
91 180584 3/8 UNIVERSAL ITTING 1
92 192813 QUICK EXHAUST VALVE CAGE 2
= GREASE (AGMD-010)
= LOCTITE
= TORQUE
= GREASE INTERNAL (AGMD-010)
= MAINTENANCE ORDER
(REVERSE FOR ASSY)
= MAGNET HAZARD
KEY

Instruction Manual
Page 11 of 16 Issue: 1.1
Removal of a single fluid piston
16mm
10mm

Instruction Manual
Page 12 of 16 Issue: 1.1
Fault Finding
Symptom Possible Cause Remedy
Pump will not
‘Prime’
a. Air getting into the suction
hose/manifold
b. Worn piston seals
c. Ball checks not seating correctly
a. Check seals and hose connections
b. Replace piston seals
c. Inspect, clean/replace balls/seats
Pump will not run a. No Air or Fluid supply
b. Air piston seal worn.
c. Pilot valve assemblies inoperable.
d. Main air valve inoperable
e. QE diaphragm defective
f. Ball checks not seating
a. Check air and fluid supply ball valves
and supply hoses.
b. Replace Piston seal
c. Switch/interchange pilot valves to
isolate faulty pilot valve and
clean/replace.
d. Check clean/replace Air valve.
e. Check for constant exhaust air when
pump is not running. Check/replace
QE diaphragms
f. Inspect, clean and/or replace balls
and seats.
Pump runs but has
excessive pulsation
a. Air getting into fluid line, air supply
restricted.
b. Obstructed fluid ball checks.
c. Worn air motor piston seals.
d. Worn/failed air motor shaft seals.
e. Worn fluid piston seal.
f. Air exhaust restricted.
a. Check seals and hose connections.
Check air supply
b. Remove, clean, and inspect seat,
ball, and ball cage. Replace if
suspect or worn.
c. Replace air motor piston seal.
d. Disassemble pump as required to
replace air motor shaft seals.
e. Replace fluid piston seal.
f. Check QE diaphragms and exhaust
outlets.
Paint leaking into
detection hose (38)
Air bleeding from
vent plug (36)
a. Bellows seal failure
b. Air motor shaft seal leaking. (Air
leak from vent plug 36).
a. Replace bellows seal (27)
b. Check air motor shaft seal (6),
replace as necessary

Instruction Manual
Page 13 of 16 Issue: 1.1
Spares Kits for Maple 7/15 Pump
Kit No. Part No. Description Remarks

250653 Fluid Section Service Kit Check Main Parts List
for details of individual
Kit Contents

250726 Fluid Section Overhaul Kit

250657 Air Motor Seal Kit
#
192765 Pilot Valve Assembly 2off per Pump
#
0115-010015 Main Spool & Sleeve Valve Assembly 1off per Pump
#
193195 Piston Seal 2off per Pump
#
192881 Knifed Bellows 2off per Pump
# - Recommended Spare Parts for continually running pumps
Maintenance Schedule
Inspection Operation
Daily Check for any general fluid or air leakage.
Weekly
Inspect Pump for Correct operation
Check for any excessive mechanical noise
Check for excessive fluid pressure pulsation
6 Monthly Test
Perform a pump stall test to ensure correct operation.
•If pump does not stall check fluid piston seals and ball
checks, replace as required.
•If air is escaping through exhaust check air motor piston seal
and quick exhaust diaphragm, replace as required.
12 to 36 Months
(Typically 10 million
Pump Cycles
dependant on air
quality and
abrasiveness of the
paint used)
Replace Air Piston seal
Replace shaft seals & bearings
Inspect and replace if required:-
Pilot Air Valves
Main Air Valve Parts
Replace Fluid Piston Seal
Replace Balls and Seats
Replace Bellows

Instruction Manual
Page 14 of 16 Issue: 1.1
Installation
This product should be flushed with a suitable compatible solvent prior to use.
Mount the pump securely and position the pump at a convenient height (below the
lid height of the paint container), to allow for maintenance, visual observation, and
periodic inspection. The wall mount bracket is included with all pumps.
The Pump Mounting bracket must be connected to a suitable earth ground to ensure
that there is no possibility of static build up.
Attach suitable flexible hoses to the inlet and outlet connections. Connect a suitable
3/8 NB air hose and ½” Pressure Filter Regulator to the air motor. (Filter rated at
minimum 1000 L/min)
No additional air lubrication is required as piston ring lubricant is applied during
assembly or repair. If an air lubricator is used then this must be maintained.
Set the pump speed to a slow cycle rate and start the pump to remove any air from
the fluid circuit before increasing pressure. Inspect for any air or fluid leaks.
If an air blow out system is used, never exceed 2 Bar on the inlet of the pump.
Exhaust kits are available for these pumps if the air exhaust is required to be piped
away from the pump rather than exhausting locally through the mufflers.
Accessories
Part No. Description Remarks
192206 1” Sanitary Gasket
192009 1 & 1½” Sanitary Clamp
502608 Seal Insertion Tool For Shaft seal (9)
502769 Bellows Assembly Tool
502382 Bellows Assembly Spigot
AGMD-010 Kluber Isoflex Topas NB 52 (Grease type #) 50 ml Tube
192779 Exhaust Tube Adapter (1” NB hose) For piped exhaust
192820 Exhaust Tube Adapter (1¼” NB hose) For piped exhaust
192803 1” Manifold Plug For piped exhaust
192821 1” BSP Heavy Duty Mufflers Recommended for high pump
pressures and cycle rates

Instruction Manual
Page 15 of 16 Issue: 1.1

Instruction Manual
Page 16 of 16 Issue: 1.1
Justus-von-Liebig-Straße 31, 63128 Dietzenbach. DE
Tel. [phone] Fax. [phone]
General e-mail: [e-mail]
163-171, Av. des Auréats, 26014 Valence cedex. FR
Téléphone : [phone] Télécopie: [phone]
General e-mail: [e-mail]
USA Canada Customer Service
195 Internationale Blvd.
Glendale Height,IL 60139
630-237-5000
Toll Free Customer Service and
Technical Support 800-992-4657
Toll Free Facsimile 800-246-5732
Binks registered office Finishing Brands Germany GmbH Justus-von-Liebig-Straße 31, 63128 Dietzenbach. Amtsgericht Offenbach HRB 43560
Ringwood Road, Bournemouth, Dorset BH11 9LH. UK
Tel. [phone] Fax. [phone]
General e-mail: [e-mail]