Binks Maple 30/3 User manual

EN
Maple 30/3 Pump
• Model 104010
IMPORTANT! DO NOT DESTRO
Y
It is the Customer's responsibility to have all operators and service personnel read and understand this
manual.
Contact your local Carlisle Fluid Technologies representative for additional copies of this manual.
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
Service Manual
77-3235 R4.6 www.carlisleft.com

EN
Product Description / Object of Declaration: Pumps - Maple, DVP, 104009, 104010/LS, 104016,
104027, 104032, 104040/1/2, 104077, 104020,
104023, 104025, 104028/9, 106933, 104205,104149-
52, 104207-15, 104147.
This Product is designed for use with: Solvent and Water based materials
Suitable for use in hazardous area: Zone 1
Protection Level: II 2 G X IIB T4
Notified body details and role: Element Materials Technology (0891)
Lodging of Technical file
EU Declaration of Conformity

The object of the declaration described above is in conformity with the relevant Union
harmonisation legislation:
Machinery Directive 2006/42/EC
ATEX Directive 2014/34/EU
by complying with the following statutory documents and harmonized standards:
EN ISO 12100:2010 Safety of Machinery - General Principles for Design
EN 12621:+A1:2010 Machinery for the supply and circulation of coating materials under pressure - Safety
requirements
EN 1127-1:2011 Explosive atmospheres - Explosion prevention - Basic concepts
EN 13463-1:2009 Non electrical equipment for use in potentially explosive atmospheres - Basic methods and
requirements
EN 13463-5:2011 Non electrical equipment for use in potentially explosive atmospheres - Protection by
constructional safety "c"
Providing all conditions of safe use / installation stated within the product manuals have been
complied with and also installed in accordance with any applicable local codes of practice.
Si
g
ned for and on behalf of Carlisle Fluid
Technologies UK Ltd:
This Declaration of conformity / incorporation
is issued under the sole responsibility of the
manufacturer:
Carlisle Fluid Technologies UK Ltd,
Ringwood Road,
Bournemouth, BH11 9LH. UK
D Smith Director of Sales (EMEA)
27/6/18
Bournemouth,BH11 9LH,UK
77-3235 R4.6 2/24 www.carlisleft.com

EN
PROP 65 WARNING. WARNING: This product contains chemicals
known to the state of California to cause cancer and birth defects or
other reproductive harm.
PINCH POINT HAZARD. Moving parts
can crush and cut. Pinch points are
any areas where ther are moving
parts.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE
OPERATOR OF THE EQUIPMENT.
NOTE
Hazards or unsafe practices which could result in
severe personal injury, death or substantial property
damage.
Hazards or unsafe practices which could result in
minor personal injury, product or property
damage
Important installation, operation or maintenance
information.
WARNING
Read the following warnings before using this equipment.
In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as
follows:
WARNING CAUTION
READ THE MANUAL. Before operating finishing equipment, read and
understand all safety, operation and maintenance information
provided in the operation manual.
AUTOMATIC EQUIPMENT. Automatic
equipment may start suddenly without
warning.
WEAR SAFETY GLASSES. Failure to wear safety glasses with side
shields could result in serious eye injury or blindness. PROJECTILE HAZARD. You may be
injured by venting liquids or gases that
are released under pressure, or flying
debris.
DE-ENERGIZE, DE-PRESSURISE, DISCONNECT AND LOCK OUT ALL
POWER SOURCES DURING MAINTENANCE. Failure to de-energize,
disconnect and lock out all power supplies before performing
equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT
OFF THE EQUIPMENT IN CASE OF AN
EMERGENCY.
NOISE LEVELS. The A-weighted sound level of pumping and spray
equipment may exceed 85 dB(A) depending on equipment settings.
Actual noise levels are available on request. It is recommended that
ear protection is worn at all times while equipment is in use.
PRESSURE RELIEF PROCEDURE.
Always follow the pressure relief
procedure in the equipment instruction
manual.
INSPECT THE EQUIPMENT DAILY. Inspect the equipment for worn or
broken parts on a daily basis. Do not operate the equipment if you
are uncertain about its condition.
OPERATOR TRAINING. All personnel
must be trained before operating
finishing equipment.
EQUIPMENT MISUSE HAZARD. Equipment misuse can cause the
equipment to rupture, malfunction or start unexpectedly and result in
serious injury. PACEMAKER WARNING. You are in the
presence of magnetic fields which may
interfere with the operation of certain
pacemakers.
HIGH PRESSURE CONSIDERATION. High pressure can cause serious
injury. Relieve all pressure before servicing. Spray from the gun,
hose leaks or ruptured components can inject fluid into your body
and cause extremely serious injury. KEEP EQUIPMENT GUARDS IN PLACE.
Do not operate the equipment if the
safety devices have been removed.
STATIC CHARGE. Fluid may develop a static charge that must be
dissipated through proper grounding of the equipment, objects to be
sprayed and alll other electrically conductive objects in the dispensing
area. Improper
g
roundin
g
or sparks can cause a hazardous condition
and result in fire, explosion or elecrtic shock and other serious injury.
NEVER MODIFY THE EQUIPMENT. Do
not modify the equipment unless the
manufacturer provides written
approval.
77-3235 R4.6 3/24 www.carlisleft.com

#
#
Specification
Ratio: 3:1
Maximum air inlet pressure: 7 bar [101.5 psi]
Maximum fluid pressure: 21 bar [304.5 psi]
Nominal flow volume / cycle: 0.75 l/m [0.20 US gal/m]
Output @ 60 cycles / min: 45 l/m [12 US gal/m]
Dirt: 5 microns
Water: -20°C @ 7bar [940ppm]
Compressed Air Inlet 3/8" BSPP / NPSM
A
ir consumption @ 15 cycles/min and 6 bar [87 psi] air inlet
pressure:
Max. Pump Fluid Inlet Pressure
Maximum recommended continous cycle rate:Cycles/min 20
Air volume / cycle @ 3.1 bar/45psi: 9.5 l/m [0.33 SCFM] @ 3.1 bar [45 psi]
1 1/2" Sanitary
Fluid outlet connection: 1 1/2" Sanitary
283 l/m [10 CFM]
A
ir consumption @ 30 cycles/min and 6 bar [87 psi] air inlet
pressure: 595 l/m [20CFM]
EN
Maximum recommended intermittent cycle rate:Cycles/min 40
Fluid inlet connection:
2 bar [30 psi]
A
ir Quality ISO 8573.1 Class 3.3.2
Air volume / cycle @ 6.2 bar/90psi: 18.5 l/m [0.65 SCFM] @ 90 psi [6.2 bar]
Oil: 0.1mg/m³
Weight: 35 kg / 77 lbs
Note:
See Note
Class 3.4.2 Air Quality (Refrigerant dried - water +3ºC@7bar) may be used, however,
above 15 cycles/min optional heavy duty mufflers 192821 or piped exhaust system should
be used, if used continuously.
77-3235 R4.6 4/24 www.carlisleft.com

EN
3/8" BSP/NPS
Dimensions and Mounting Details
MOUNTING LOCATIONS
SECTION A-A Air Inlet
1 ½" Sanitary inlet
1 ½" Sanitary outlet
77-3235 R4.6 5/24 www.carlisleft.com

EN
This product should be flushed with a suitable compatible solvent prior to use.
The wall mount bracket is included with all pumps.
If an air lubricator is used then, this must be maintained.
Installation
Connect a suitable 3/8" NB air hose and 1/2” Pressure Filter Regulator to the air motor.
Attach suitable flexible hoses to the inlet and outlet connections.
(Filter rated at minimum 1000 l/min)
No additional air lubrication is required as piston ring lubricant is applied during assembly or repair.
The Pump Mounting bracket must be connected to a suitable earth ground to ensure that there is no
possibility of static build up.
Mount the pump securely and position the pump at a convenient height (below the lid height of the
paint container), to allow for maintenance, visual observation, and periodic inspection.
77-3235 R4.6 6/24 www.carlisleft.com

EN
Set the pump speed to a slow cycle rate and prime the pump to remove any air before increasing
pressure.
A Back Pressure Regulator should be mounted in the paint system return line.
The return line ‘back pressure’ regulator responds to the changes in system fluid flow demand, (due to
variable paint usage) by dynamically adjusting the paint flow rate returning to the system paint tank,
thus maintaining the set pressure.
Set the pump cycle rate to achieve the required paint volume and then adjust the system back
pressure regulator and pump air pressure to achieve the desired system fluid pressure.
Installation
Inspect for any air or fluid leaks.
If an air blow out system is used, never exceed 2 bar [29 psi] on the inlet of the pump.
Exhaust kits are available for these pumps if the air exhaust is required to be piped away from the
pump rather than exhausting locally through the mufflers.
77-3235 R4.6 7/24 www.carlisleft.com

EN
2
M8
x 25
2
M8 8
M12 16
M12
x 40
Ø1
3/8
"2
1 1/2" 4
1 &
1 1/2"
4
2
2
2
2
2
2
2
1
1
1" 2
BINKS 1
1
1
Ø100 2
104010-LS
165108
165137
6
SPRING WASHER
SPRING WASHER
23
24
25
26
INLET MANIFOLD
OUTLET MANIFOLD
LABEL
BALL
SANITARY GASKET
SANITARY CLAMP #
4192009
PISTON ASSEMBLY
1/4" BSP HEXAGON PLUG
194237
28

#
192775
192776
192777
194243
165960 SOCKET HEAD CAP SCREW 16
NAMEPLATE
INLET CYLINDER192597
192626
192629
192632
192816
193705
193775
SEAT
PISTON SEAL
HEAVY DUTY MUFFLERS192821 1" 2
11
4
SPRING1605131
5
3
7
8
ITEM PART NO. DESCRIPTION QTY REMARKS
171788
164838 No.2 x 4.75 RIVET
23
14
15
16 
17
OUTLET CHECK

18
OUTLET CYLINDER
#
12 192595
192596
20 192648 Ø41.0 x 1.78 O-RING 2 

2O-RINGØ50.52 x 2.6219264719
Pump AssemblyPARTS LIST -
SOCKET HEAD CAP SCREW
27
192008
192551
4O-RINGØ12.42 x 1.7819250510
AIR MOTOR ASSEMBLY
21
22
13
VALVE MUFFLER
9
BALL CAGE
INLET SPRING KEEP
164472
77-3235 R4.6 8/24 www.carlisleft.com

EN
Pump Assembly
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
77-3235 R4.6 9/24 www.carlisleft.com

EN
2
1
2
2
M6
x 30
M8 16
M4
x 16
M8 16
M4 4
M4 4
M10
x 12
2
2
1
6
2
2
2
2
1
1/8R
- 6mm
-PARTS LIST
SOCKET HEAD CAP SCREW
SOCKET HEAD CAP SCREW
BUTTON HEAD CAP SCREW
PUSH IN ELBOW
13
SPRING WASHER
RETAINING NUT
22
23
24
CYLINDER STUD
CYLINDER STUD - LONG
BELLOWS SPACER
PUMP BRACKET
VENT PLUG
EXHAUST ADAPTER
BELLOWS LEAK DETECTION HOSE
192764
192799
16
KNIFED BELLOWS
AIR CYLINDER
4

10115-010037 POPPET ASSEMBLY
#
20115-010102 AIR VALVE ASSEMBLY
#

7162703 SHAFT SEAL
8162704 SHAFT BEARING

#
10
Air Motor Assembly
ITEM PART NO. DESCRIPTION QTY REMARKS
165528
163920
165970
165971
12
165108 SPRING WASHER
11
9
165963 DOME NUT
PLAIN WASHER
4
4
18
19
192812
2


2
1
226
25 192814
192815

4
END PLATE MACHINING28 194599 2
14
15
17
20
21
177038
192374
192579
161992
161993
161994
1619956
5
4
3
O-RING
O-RING
O-RING
O-RING
Ø19.5 x 3.00
Ø4.47 x 1.78
Ø20.35 x1.78
Ø117.5 x 2.62
192757
192761
192762
192763
119429327 AIR MOTOR PISTON ASSY
2

77-3235 R4.6 10/24 www.carlisleft.com

EN
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
ITEM 7 DETAIL
77-3235 R4.6 11/24 www.carlisleft.com

EN
2
1
194293
-
Air Motor Piston Assembly
GRUB SCREW 1165964 M12 x 402
ITEM PART NO. DESCRIPTION QTY REMARKS
3192759 PISTON SHAFT
4192760 PISTON

1AIR MOTOR PISTON SEAL1627021
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
77-3235 R4.6 12/24 www.carlisleft.com

EN
1
2
2
2
2
2
1
1
1
3/8" 1
1/8 BSPT PIPE PLUG
12 180584 UNIVERSAL FITTING
60115-010021 1.5 x 36 O-RING

70115-010049 2 x 20 O-RING

80115-010073 M4 x 12 BUTTON HEAD CAP SCREW 8
QUICK EXHAUST VALVE CAGE19281313 2
90115-010097 VALVE BLOCK
10 0115-010103 1/4 BSPT PIPE PLUG
11 0115-010107
20115-010016 BUMPER

30115-010017 MAGNET

SPOOL AND SLEEVE O-RING162789 6 Not Shown
50115-010020 DIAPHRAGM

Air Valve Assembly
ITEM PART NO. DESCRIPTION QTY REMARKS
10115-010015 SPOOL AND SLEEVE ASSEMBLY
#
2VALVE BLOCK END CAP0115-0100184
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
77-3235 R4.6 13/24 www.carlisleft.com

EN
1
1
Ø82.22 x2.62
1
1.375 1
1
1
Ø100 1
1
7192631 SEAT

8193626 FLUID PISTON
9193627 BALL CAGE
3162807

4162854

5171784 BALL

6192629 INLET SPRING KEEP

Ø50.52 x1.78 O-RING
O-RING
ITEM PART NO. DESCRIPTION QTY REMARKS
2162805

PISTON BALL CHECK SPRING16051311

Ø63.17 x 2.62 O-RING
Fluid Piston Assembly
-
194243
Use a 32mm Single Hex
Socket when tightening or
removing ball cage
from Piston.
KEY
LOCTITE
TORQUE
MAINTENANCE ORDER
(Reverse for assembly)
GREASE INTERNAL
(AGMD-010)
GREASE
(AGMD-010)
77-3235 R4.6 14/24 www.carlisleft.com

EN
No air or fluid supply Check air and fluid supply ball
valves and supply hoses.
Air piston seal worn. Replace piston seal.
Pilot valve assemblies inoperable.
Switch/interchan
g
e pilot valves to
isolate faulty pilot valve and
clean/replace.
Main air valve inoperable. Check clean/replace Air valve.
Ball checks not seating correctly. Inspect, clean and/or replace
balls and seats.
Fault Finding
Symptom Possible Cause Remedy
Pump will not
‘Prime’
Air getting into the suction hose/manifold Check seals and hose
connections.
Worn piston seal. Replace piston seals.
Ball checks not seating correctly. Inspect, clean and/or replace
balls and seats.
Check for constant exhaust air when
pump is not running.
Check/replace QE diaphragms.
QE diaphragm defective.
Pump will not run
77-3235 R4.6 15/24 www.carlisleft.com

EN
Check seals and hose
connections.
Remove, clean, and inspect seat,
ball, and ball cage.
Fault Finding
Symptom Possible Cause Remedy
Worn air motor piston seals. Replace air motor piston seal.
Worn/failed air motor shaft seals. Disassemble pump as required to
replace air motor shaft seals.
Worn fluid piston seal. Replace fluid piston seal.
Air exhaust restricted. Check QE diaphragms and
exhaust outlets.
Paint leaking into
detection hose, air
bleeding from vent
plug
Bellows seal failure Replace bellows seal
Air motor shaft seal leaking Check air motor shaft seal
replace as necessary
Check air supply
Air getting into fluid line, air supply restricted.
Replace if suspect or worn.
Obstructed fluid ball checks.
Pump runs but has
excessive pulsation.
77-3235 R4.6 16/24 www.carlisleft.com

EN
1
# -
*
**
Spares Kits for Maple 30 Pump
KIT No. PART NO. DESCRIPTION QTY REMARKS

Pumps before serial number 53971 will require; Pilot spool assembly 192765, Control valve kit 250620.
250768** Fluid section seal kit 1
1
1Air Motor Seal Kit
Fluid overhaul kit
250618
250738**

Note:
Fluid section seal & fluid section overhaul kits contain all the necessary components to service Mark one
and two pistons.
Discard components not required.
250628* Control Valve Kit

1 1 off per pump
1Piston seal194237#
2 off per pump1Knifed Bellows192579#
Recommended spare parts for continually running pumps
#0115-010015 Main Spool & Sleeve Valve Assembly
Check main parts list
for details of
individual kit contents
2 off per pump1Poppet Assembly 0115-010037*#
2 off per pump
77-3235 R4.6 17/24 www.carlisleft.com

EN
Inspect and replace if required:
Pilot Air Valves & Main Air Valve Parts.
Maintenance schedule
Daily Check for any general fluid or air leakage.
Weekly
Inspect Pump for Correct operation
Check for any excessive mechanical noise
Check for excessive fluid pressure pulsation
Perform a pump stall test to ensure correct operation.
If pump does not stall, check fluid piston seals and ball checks, replace as
required.
12 to 36 Months (Typically 10
million pump cycles
dependant on air quality and
abrasiveness of the paint
used)
Replace air piston seal,
Replace shaft seals & bearings.
Replace fluid piston seal,
Replace Balls,Seats and Bellows.
If air is escaping through exhaust, check air motor piston seal and quick exhaust
diaphragm, replace as required.
6 Month Test
OperationInspection
77-3235 R4.6 18/24 www.carlisleft.com

EN
1
Smear loctite 572 over nose of bellows,
thread nut onto bellows ensuring the
thread starts squarely. Grip bellows
lightly by hand and tighten the nut with
a 1" A/F spanner until the nut contacts
the bellows shoulder.
Using Item No. 1, push bellows over
spigot until located in groove.
Screw Item No. 2 (assembly spigot)
onto the piston shaft
Bellows Replacement
ITEM PART NO. DESCRIPTION QTY REMARKS
1502769 Bellows positioning tool 1
2502382 Bellows assembly spigot
12
77-3235 R4.6 19/24 www.carlisleft.com

EN
Seal Insertion Tool
502382 Bellows assembly spigot
AGMD-010 Kluber Isoflex Topas NB 52 Grease 50ml Tube
192779
192820 Exhaust Tube Adapter (1.5” NB hose) For piped exhaust
192803 1" Manifold Plug For piped exhaust
192821 1" BSP Heavy Duty Mufflers Recommended for high pump
pressures and cycle rates
502608 For Shaft seal (7)
502769 Bellows Positioning Tool
Exhaust Tube Adapter (1” NB hose) For piped exhaust
Accessories
ITEM PART NO. QTY
192008 1 & 1 1/2" Sanitary Gasket
192009 1 & 1 1/2" Sanitary Clamp
77-3235 R4.6 20/24 www.carlisleft.com