Binks MX6805PU-SMX User manual

Instruction Manual
Page 1 of 20 Issue: 1.1
Instruction Manual
MX6805PU-SMX Pump
MX6812PU-SMX Pump
MX6833PU-SMX Pump

Instruction Manual
Page 2 of 20 Issue: 1.1

Instruction Manual
Page 3 of 20 Issue: 1.1
Specification
Feature Unit
Flow at 60 cycles/min 1.08 US Gal. /min.
4.08 Litres/min.
Flow per cycle 0.018 US Gallons
0.068 Litres
Recommended intermittent cycle rate 20 cycles/min
Pump Stroke 3”
75 mm
Ratio – MX6805PU-SMX
MX6812PU-SMX
MX6833PU-SMX
5:1
12:1
33:1
Maximum Fluid Pressure 3830 PSI
265 BAR
Fluid Inlet
Fluid Outlet
Ram – Chop Check
½” NPT (f)
Weight – MX6805PU-SMX
MX6812PU-SMX
MX6833PU-SMX
15 KG / 33 Lbs
15 KG / 33 Lbs
18 KG / 39.6 Lbs
Rod Upper Packing Seal PTFE + UHMWPE
Rod Lower Packing Seal PTFE + UHMWPE
Air Inlet Ø12 Hose Female
Air Quality ISO 8573.1 Class 3.3.2
Dirt 5 microns
Water -20ºC@7bar (0.1g/m³)
Oil 0.1mg/m³

Instruction Manual
Page 4 of 20 Issue: 1.1

Instruction Manual
Page 5 of 20 Issue: 1.1

Instruction Manual
Page 6 of 20 Issue: 1.1
MX6805PU-SMX Overall Dimensions

Instruction Manual
Page 7 of 20 Issue: 1.1
MX6812PU-SMX Overall Dimensions

Instruction Manual
Page 8 of 20 Issue: 1.1
MX6833PU-SMX Overall Dimensions

Instruction Manual
Page 9 of 20 Issue: 1.1
General Description
The MX68xxPU-SMX fluid paint pump is designed for pumping High Viscosity
materials such as Mastic, PVC, Underseals, Sound deadeners and other similar
materials.
The fluid section is a ‘ROD’ type design which means the rod displaces the
material and is the only wear contact with the packings. A ball check valve system
in the rod and a chop check inlet valve system ensure a precise, smooth volume
output. Tungsten Carbide ball seats ensure maximum operating life between
servicing.
The interior design maintains high flow capacity with minimum pressure drop
ensuring high efficiency; special surface treatments provide a smooth micro
surface making cleaning and flushing easier.
The piston and rod seals are the chevron type, which can be adjusted by means of
a gland nut, should wear occur, a preloaded wave spring is employed to adjust
and maintain the lower chevron packing preload when wear occurs. A built in
Solvent cup cleans and lubricates the pump rod and seals to prolong working life.
The air motor also utilises the Binks quick exhaust technology to prevent air valve
freezing conditions when high cycle speeds are employed.
The air motor is furnished with an exhaust muffler to control air exhaust noise
emission. An adapter kit is also available to facilitate connection to a piped
exhaust system if required.
Installation
This pump should be flushed with a suitable compatible solvent prior to use.
It is recommended that a propriety 1/2" BSP Filter / Regulator is used to provide
final control of the compressed air to the air motor.
Mount the pump securely and position the pump at a convenient height to allow
for maintenance, visual observation, and periodic inspection.
The Pump Assembly must be connected to a suitable earth ground to ensure that
there is no possibility of static build up.
Attach suitable pipework or flexible hoses designed to meet the working pressure
of the pump assembly (dependent on pump ratio) to the outlet connection, e.g. ½”
Outlet.
Set the pump speed to a slow cycle rate and start the pump to remove any air
from the fluid circuit. Inspect for any air or fluid leaks.

Instruction Manual
Page 10 of 20 Issue: 1.1
MX6805PU-SMX Pump Assembly