PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS FEATURES - OPERATIONS
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Before connecting the heater, check that the voltage
indicated on the rating plate corresponds to the main
voltage in your home/office.
2. WARNING: In order to avoid overheating, do not
cover the heater.
3. DO NOT position the heater directly under a
power socket.
4. DO NOT use this heater in the immediate surroundings
of a bath, a shower or a swimming pool.
5. If the supply cord or plug is damaged, it must be
replaced by the manufacturer or its service agent or
similarly qualified person in order to avoid hazard.
The heater contains no user serviceable parts. Should
the product suffer damage or breakdown, it must be
returned to the manufacturer or their service agent
for service.
6. Under the environment with electrical fast transient,
the product may malfunction.
7. DO NOT use this heater with a programmer, timer or
any other device that switches the heater on
automatically, since a fire risk exists if the heater is
covered or positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10. DO NOT position where it can be touched by children,
especially the very young.
11. Use this appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by Jarden
Consumer Solutions may cause hazards.
12. Allow a safe area around the heater away from
furniture or other objects; at least 50 cm from the
top and sides and 200 cm at the front. The heater is
to be placed at least 3m from water source.
13. DO NOT use this heater when it is lying on its side.
14. DO NOT use the heater in rooms with explosive gas
(e.g. petrol) or while using oxygen, inflammable glue
or solvent (e.g. when gluing or varnishing parquet
floors, PVC etc.)
15. DO NOT insert any objects into the heater.
16. Keep the mains cord at a safe distance from the main
body of the heater.
17. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by Jarden Consumer Solutions or an authorized
Jarden Consumer Solutions Center.
18. If overheating occurs, the built-in overheating safety
device will switch off the heater.
19. DO NOT place the cord under a rug.
20. DO NOT place anything on top of unit.
21. The heater cannot be used adjacent to curtains or
combustible material. Curtains or combustible
material may be burned if the heater was installed
incorrectly.
22. Always turn the appliance off before unplugging it.
23. CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cutout,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
24. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with
the appliance.
25. This heater is filled with a precise quantity of special
oil. Repairs requiring opening of the oil container are
only to be made by the manufacturer or his service
agent who should be contacted if there is an oil leak;
26 When scrapping the heater, follow the regulations
concerning the disposal of oil.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
DESCRIPTIONS (SEE FIG. 1, 2 & 3)
A. Heated Fins
B. Vents
C. Handle
D. Front Panel
E. Cord Storage
F. Power Cord
G. Front Stand
H. Control Knob
I. Power Light
J. Thermostat Knob
K. Q Shape Screw
L. Casters
M. Foot Plate
N. Wing Nut
O. U-bolt
TECHNICAL SPECIFICATIONS
BOH1501/W
Wattage: 1500W
BOH2001/W
Wattage: 2000W
ASSEMBLY INSTRUCTIONS (See Fig. 3)
Please make sure the heater has not been
plugged into any electricity outlet.
Carefully remove heater from box. Some accessories are
packed internally. Please make sure you have all of the
following accessories prior to throwing away packaging.
1 Foot Plate with 2 casters (M&L), 1 Front Stand (G),
and 1 Q shape Screw (K) and 1 Wing Nut (N) fastened
to U-bolt (O).
Note: This unit is for FLOOR USE ONLY.
1. Turn the heater upside down and you will see
one U-bolt (O) with wing nut over the last joint
of the heater.
2. Unscrew the wing nut (N) from the U-bolt (O).
3. Place one hole of the foot plate (M) to the L shape
of the U-bolt (O) and the other hole of the foot plate
into the other end of the U-bolt, then screw on the
wing nut (N).
4. Place the front stand (G) on the bottom of the
radiators front panel, and secure it with the Q shape
screw (K). This front stand (G) is not meant to be
removed once it is attached to the bottom of the unit.
5. After installation of the front stand (G) and foot plate
(M) with casters (L) turn the heater the right way up:
the heater is now ready for use.
OPERATING INSTRUCTIONS
(See Fig. 1&2)
1. Set the unit to the OFF (O) position.
2. Plug in heater. The Power Light (I) will illuminate
and remain lit until the heater is unplugged.
3. Set the Thermostat Knob (J) all the way to the right.
4. Turn the Control Knob (H) to desired level of heat.
NOTE: When the heater is in use, it is normal that
the heater cycles ON and OFF, this is to maintain your
desired temperature.
After using the heater, turn the Control Knob (H) to
“0” position, turn the Thermostat Knob (J) to lowest
temperature position and unplug the heater from
the socket.
BOH1501/W: 1-600W, 2-900W, 3-1500W
BOH2001/W: 1-800W, 2-1200W, 3-2000W
SETTING THE THERMOSTAT
1. Set the Thermostat control all the way to max.
2. When the desired temperature/comfort level is
reached, turn the thermostat control anti-clockwise
to lower position or until the heater stops operating.
3. The control will now automatically maintain the
pre-set temperature level by turning the heater
ON and OFF.
NOTE: The Power light will remain lit during operation.
NOTE: It is normal for the heater to cycle ON and OFF as
it maintains the preset temperature.
ANTI-FROST GUARD INSTRUCTION
If you plug in the heater, it will start working at the
lowest temperature setting (When thermostat control
is in the lowest temperature position, the temperature
will be maintained at 5° C, thus the heater will be in the
off status unless the room temperature is lower than 5°
C. If the room temperature is lower than 5° C, the heater
will automatically start working and will keep turning
on & off all the time, maintaining its ambient temperature
of 5° C.
NOTE: Unit must be unplugged for it to be fully off
TIP OVER PROTECTION
When the unit is accidentally knocked over, or tilts on one
side at more than a 45° angle; it will instantly shut off.
To reset, simply place the heater in an upright position.
STORAGE TIPS
If the heater is not required for long periods, for example
during the summer, it should be stored at room
temperature; in a dry place and preferably covered to
prevent the accumulation of dust and dirt.
Figure 1
Figure 3
Figure 2
AB
C
D
E
GF
L
BOH2001
H
I
J
GKL
M
N
O
AB
C
D
E
GF
L
BOH2001
H
I
J
GKL
M
N
O