Bioness L300 Go Parts list manual

Clinician’s Reference Card
Component Pairing
612-00851-001 Rev. D
IMPORTANT: Pair system components before pairing to Clinician Application
1
2
L300 Go®, Bioness, the Bioness Logo®and LiveOn®are trademarks of Bioness Inc. | www.bioness.com
1
60sec
Fitting the L300 Go System
Attach the personal panel.
Slide the personal strap cover over the Cuff strap.
Wipe the stimulation area with a damp, soft cloth. Then, slightly extend the lower leg.
Once the electrode(s) are attached to the L300 FS Cuff, place the cuff on the leg using the cuff
patella locator, secure strap, adjust tension.
Program stimulation settings to achieve desired response.
1
2
3
4
5
1 4 52 3
Pairing System to Clinician Application
Log into L300 Go Clinician Application
Select to access the linking screen. Place System
into Pairing Mode by simultaneously pressing plus and
minus button on EPG. Select Link icon above
desired leg. Once paired, exit linking screen by clicking
on
Select a patient i.e. Work with Existing patient, Create
New or Choose from List.
If selecting from the Patient List, press the
Upload icon or double click the chosen name.
1
2
3
1
3
2
Thigh FS Cuff with Lower FS Cuff.
EPG Pairing Mode Activation: Simultaneously press
on the Plus and Minus button on each EPG. EPG status
indicator light will flash Green, Yellow, Red.
If needed, pair the Foot Sensor to the Lower FS Cuff EPG.
Foot Sensor Pairing Mode Activation: Pair the Foot
Sensor to a new EPG by placing a battery (CR2032) into
the Foot Sensor and pressing on the pressure sensor,
green light will blink to confirm pairing mode activation.
Place the lower EPG in pairing mode.
2

Rx Only (US only)
1
1
2
3
4
2
3
4
5
Fitting the L300 Go Thigh System
Programming the L300 Go System
Wet the Thigh cloth electrodes and snap into cuff.
Wipe the stimulation area with a damp, soft cloth. Place the cuff on the thigh, no less than three
finger widths proximal to the popliteal fossa (hamstring application) or patella (quadricep application).
Center the cuff on the midline of the thigh. Fasten the straps.
Program stimulation settings with the patient seated to achieve desired response.
If necessary, adjust stimulation settings with the patient standing.
Bioness Europe B.V.
Stationsweg 41
3331 LR Zwijndrecht, The Netherlands
Telephone: [phone]
Email: [email protected]
Website: www.bioness.com
Bioness Inc
25103 Rye Canyon Loop
Valencia, CA 91355
Telephone: [phone]
Email: [email protected]
Website: www.bioness.com
Program Stim Settings. Select desired EPG from the Stim Control Dashboard. Select
electrode type (Steering Electrode screen shown in image). With the patient seated, press
Test to turn on stimulation on the selected EPG. Adjust settings to achieve desired response. Press
Test to stop stimulation. Repeat step for all connected EPGs.
Program Gait Settings. Press Gait Screen icon. Press Stim Wave icon
to enable Gait Mode. Observe patient walking and adjust settings as needed. Press
Stim Wave icon to stop stimulation.
Program Training Settings. Press Training Screen icon. Adjust training settings,
inclusive of excluding a specific EPG as desired. Press Training icon to turn stimulation
on all paired devices that are included in training mode. Press Training icon to stop
stimulation.
At the end of each session unlink the system by navigating to the Linking Screen and pressing
on the Unlink icon. Exit the Clinician Application.
3 4
12
Test
Test
Note: Press and hold the Manual Stimulation icon to activate stimulation on all paired and active EPGs
while the button is pressed.
For more information, visit:
www.bionessuniversity.com
123 4