BIOS AP DVPro T10-U3 User manual

Quick Installation Guide
—USB3.1 model
Introduction
This Quick Installation Guide(QIG) describes the packing content and
installation guide line for DVPro T10-USB3.1 model.
It also explains the function of each connector, and button.
It is served as a quick startup for basic configuration, and the details
can be found on User Manual (downloadable from website)
Attention
BIOS AP and its resellers are not liable for any
data or information lost or possible software
error due to adoption of the product. We do not
take any responsibility of damage and/or system
malfunction due to our product / storage device
failure or for any of the problems caused as a
result It is recommended to always backup your
data.
World’s leading USB 3.1 RAID 6 Storage High
Capacity, Quiet and High Performance
10 x 3.5” SATA Drive Support
DVPro T10-U3
—USB3.1 model －
DVPro T10–U3 model
DVProT10-U3 Jul. 2017Printing No:02
Publisher BIOS AP Inc.
6F-6A., No.5, Sec. 3, New Taipei Blvd., Xinzhuang Dist.,
New Taipei City 242, Taiwan
TEL:[phone] FAX:[phone]
Email:[email protected]m.tw Website:www.biosap.com.tw
Change of Pre-configuration (Disk Size, RAID Mode, Number of Drives)
For any reason, if required, users can change pre-configured parameters including “disk size”,
“RAID mode”, and “number of drives”
Push and hold “Mode” and “Select” button at LCD panel, push power button once to turn on the
device. LCD panel should display “Array Parameter Setting” as below, and you can release both
buttons.
ARRAY PARAMETERS
SETTING
DISK Size
xxB
RAID MODE
RAID-6
Push Mode Button and you will see “Disk Size Setup”
Push “Select” button to choose disk size if wanted. Stop at the size of choice
Push Mode button to roll into RAID Mode setup if expected
Push “Select” button to choose RAID mode if wanted. Stop at selected RAID mode
RAID 6 or RAID 5 or RAID 0 or RAID 10
Push Mode Button to choose number of drives (it shows as Drive Mode)
DRIVE MODE
10*
Push “Select” button to choose number of drives to be applied. Stop at number of drives needed
The last step is to save the change. Push both “Mode” and “Select” buttons at the same time once
to save the change. LCD should show “Power Down Please!”, if not push both buttons again. Power
down the device. Push and hold “Mode” button and power on the unit for new configuration to be
effective. After then, you need to format the new volume before using it.

Name and Function of each part
③④⑤
⑥
⑦
⑧
①
②
Power Button
Power ON /OFF Switch
②HDDAccess FAILLED
BLUE Flash upon access; Orange ON indicates an error
the FAIL LED on means the HDD is under rebuilding
⑨
Power ON LED indicator
Host Access LED indicator
⑩
⑮
⑫
⑪
⑭
⑬
1）Parameter Initialization ( Power on Initialization ) 2）Confi
gure parameters 3）Stop
buzzer alarm (
Buzzer stopped immediately by pushing one time )
Setup Parameter
⑧LCD Display
Message display screen. Show status of the system
Show parameters while doing configuration
⑨Power Inlet
AC Power Inlet
⑩
RJ45 Ethernet
Management Port
⑪
Type C Connector
USB3.1 Host
⑫
Fan Module
Fan1
Fan Module
Fan2
Disk Drive module 0 ( to 9 ). Upper left one is number 0, and right is 1
◆ Packing List
The box should contain the DVPro T10-U3 and belowaccessories:
DVProT10-U3 Body
USB3.1 Gen2 Cable A-C and C-C
Powercable
DVProT10-U3
QuickInstallationGuide ◇Packing List
● DVPro T10-U3 Body
● Powercable
● ScrewPack for HDDs
● QuickInstallationGuide
●USB3.1Gen2 A-C Cable 1 Meter
ARRAY PARAMETERS
SETTING !
InstallationGuide
For Drive installation if needed,
Follow the below instruction to install or replace disk drive.
Step 1. Step 2.
Loosen the left side rear screws Use hand or screw driver to loosen
(rear view)and open the side panel. the thumb screw of disk drive tray.
Step 3.
Prepare a flat operating table for following operation. Put the disk drive perpen-
diculous to the flat table with the drive connector toward bottom(drive connec-
tor side facing you). With thumb screw of drive tray on left hand side, slide
down the tray carefully till it touches down the flat table.
Step 4.
Get four screws from the screw
bag and tightly screw them all.
Overview of Setup method
To facilitate easy configuration of DVT10T2, a LCD/Keypad is designed on
the front panel for parameter setup. The default configuration and parameters
are designed to RAID6 mode. To avoid malfunction, parameters and configu-
ration could not be changed on use.
Begin to use
There are two ways to configure the DVT10U3 setting either by Web GUI
or LCD and keypad operation. Most parameters cannot be changed during
normal operation to avoid possible corruption or
malfunction. To start with the parameter setting, both
‘Mode’ and ‘Select’ buttons have to be pressed and
hold at power on till the LCD showing [Array Parame-
ter Setting].
After then, one can change parameters value from Web GUI or LCD button
panel. To quickly setup the unit, press “Mode” button to roll among different
parameters and “Select” button to choose their values. After change, press
“Mode” and “Select” at the same time to save modified parameters.
For details of each parameter and its meanings, please refer to User Manual
which can be downloaded from website: http://www.biosap.com.tw
The default setting might be varied for different configuration upon number
of pre-installed drives and capacity. Following parameters saved, please turn
off the power then press and hold the “Mode” button about 3 seconds while
turning on power to initialize the configured setting. New configuration or
parameters will be effective after initialization process.
Attention: Initialization process assumes data aligned to its RAID distribution
and will enforce current parameters to RAID controller. If the unit had corrupt-
ed data during last operation, the unit will be treated as normal despite of
possible uncompleted data.
⑮
●USB3.1 Gen2 C-C Cable 1 Meter