Biosonic Suvi Elite User manual

ZERO
MAX
1. Press S button to turn ON the Scaler.
2. Tip Working mode:
1. Press P button to turn ON the Polisher.
2. Tip Working mode:
3. Select scaler function:
3. Select polisher function:
4. Water regulation:
4. Water regulation:
5. Foot Pedal Control:
5. Foot Pedal Control:
6. Cleaning:
6. Cleaning:
Comprehensive cleaning function:
Turn off the polisher by holding down Pfor
a few seconds. Now the cleaning function
can be started by pressing first Cand then
P. Water or disinfectant (40 sec) and air (40
sec) cleans the handpiece. The cleaning cycle
stops automatically after 80 seconds.
The polisher is activated when the foot control
pedal is pressed down. The polishing power is
regulated with the foot pedal from:
left/ZERO = WaterJet (only water and air) middle
to right/MAX = 60 or 100% depending on which
working mode is chosen on the control panel.
Problems? See Section 6 Troubleshooting in the owner’s guide.
Air purge quick cleaning function:
To prevent clogging; air purge the handpiece
after each polisher treatment by pressing C.
or
With every push on the Pbutton, the
function toggles from:
1. Normal polishing
2. Air cleaning (only air)
3. WaterJet cleaning (only water and air)
60 % 100 %
With the water control set at highest flow
setting depress the foot pedal and slowly
reduce the water flow with the water control
wheel on the side of the powder container
until the powder starts to accumulate
on the surface as a white spot. Increase
the water flow until the spot disappears.
The polisher is now balanced for optimal
performance.
Ultrasonic Scaler QuickStart Guide:
Scaler Polisher
Comprehensive cleaning function:
The cleaning function can be started by
pressing C. Water or disinfectant cleans the
water line and handpiece. The cleaning cycle
stops automatically after 80 seconds.
The unit is in standby mode when the
power cord is connected and the green
LED is illuminated.
With every push of the Sbutton, the
function toggles from:
Scaling with water
Dry mode: scaling without water
Irrigation mode: just water, no scaling
Choose the working mode
or or
100 %
70 %
40 %
7. Push the S button for 3 seconds to
turn the scaler OFF. 7. Push the P button for 3 seconds to
turn the scaler OFF.
Depress the foot control pedal in the leftmost
position and adjust the water flow with the
control ring on the scaler handpiece until
the water is dripping.
The scaler is activated when the foot
control pedal is pressed down. The power
is regulated from left/ZERO to right/MAX
within the chosen working mode. In ZERO
position there are two functions:
a) irrigation with no scaling power: hold
the footpedal down.
b) diagnostic light: press the footpedal
once.
This working mode
cannot be activated
when using the polisher.
Recommended Optional
OFF
ON
1
1
2
2
3
4
3
4
Choose the correct working mode that is
marked on the base of each tip by pressing
the corresponding working mode button on
the keypad:

1. Consult a qualified technician to install to air and, if applicable, to water supply.
2. Connect the foot pedal cable to the foot pedal and to the rear of the unit.
3. Connect the power cord to the unit and the AC power outlet.
4. Fill the medicament bottle with water or medicament solution. Screw the bottle cap onto the bottle and push it onto the
connector on the left side of the unit. When removing the bottle, press first the depressurization button beside the connector.
5. a. Unscrew the powder container from the cap and fill with BioSonic Suvi polisher powder up to MAX.
Screw the container back onto the cap.
5. b. Connect the powder container to the connectors on the right side of the unit.
6. a. Gently slide a handpiece grip onto the polisher handpiece. Screw the nozzle clockwise into the polisher handpiece grip until
the nozzle is firmly tightened.
6. b. Gently slide a handpiece grip onto the scaler handpiece. Place the scaler tip in the torque wrench and use the torque wrench to
screw the scaler tip clockwise onto the scaler handpiece. Tighten until the resistance causes the torque wrench to begin to slip.
7. See Section 4 in
the owner’s guide for
Operation Instructions.
NOTE! Before installing and using the device please read the owner’s guide.
Installation
1.
4.
2. 3.
5b.
6b.
5a.
6a.
coltene.com
P/N 20004500A
Coltène/Whaledent Inc.
235 Ascot Parkway
Cuyahoga Falls, OH 44223 / USA
Tel. USA & Canada + 1 800 221 3046
+ 1 330 916 8800
Fax [phone]
[e-mail]
Coltène/Whaledent AG
Feldwiesenstrasse 20
9450 Altstätten / Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
Coltène/Whaledent GmbH + Co. KG
Raiffeissenstrasse 30
89129 Langenau / Germany
Tel. [phone]
Fax [phone]
[e-mail]
Polisher handpiece Scaler handpiece