Birlea RICHMOND DESK User manual

Vendor: S000180
Page 1 of 9
ASSEMBLY INSTRUCTIONS
RICHMOND DESK
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR
USE YOUR RICHMOND DESK
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
HEALTH & SAFETY:
DO NOT use this desk if any parts are missing, damaged or worn
DO NOT use this desk unless all fixings are secured
Always use on a level, even surface
CARE & MAINTENANCE:
Assemble on a soft, clean surface to prevent damages
Periodically check all screws fixings to ensure they are secure
DO NOT push the desk as this will damage the feet
Always lift the desk with two people to reposition
Keep any sharp objects away from the desk
www.birlea.com

Vendor: S000180
Page 2 of 9
Parts List Hardware List
Part Des ription Qty Part Des ription Qty
1 Left Panel 1 A 3.5 x 12 mm CSK Screw 4
2 Right Panel 1 B 3.5 x 15 mm CSK Screw 8
3 Division Panel 1 C 4.5 x 32 mm CSK Screw 8
4 Top Panel 1 D 6 x 9 mm Euro Screw 4
5 Upper Front Frame 1 E 6 x 13 mm Euro Screw 4
6 Upper Back Frame 1 F 6 x 60 mm JCBC Screw 2
7 Lower Back Frame 1 G JRN Steel Nut 2
8 Base Panel 1 H 6 x 20 mm Wooden Dowel 4
9 Shelf Panel 1 J 8 x 25 mm Wooden Dowel 28
10 Upper Front Frame 1 K 24 x 8.5 mm Bolt 21
11 Lower Front Plinth 1 L 15 x 12 mm Cam Lock 13
12 Lower Back Plinth 1 M 12 mm Cam Lock 8
13 Drawer Front 1 N1
Metal Hinge
2
14 Door 1 N2 Hinge Plate 2
15 Left Drawer Side 1 P Plastic Door Stopper 1
16 Right Drawer Side 1 Q1 Drawer Slide CR 1
17 Drawer Back 1 Q2 Drawer Slide CL 1
18 Drawer Base 1 R1 Drawer Slide DR
1
19 Base Panel 1 R2 Drawer Slide DL 1
** You will need a small mallet and a
s rewdriver for assembly
S Plastic Plug 1
T Metal Shelf Stud 4
U M4 Allen Key 1
V Backply Stopper 4
W Glue 2
X
Metal Cup Handle with Screw
1
Y Metal Ring Handle with Screw 1

Vendor: S000180
Page 3 of 9
Step 1: Insert hardware parts J and H as shown using hardware part W and a small mallet (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 2: Insert hardware part K as shown using a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 4 of 9
Step 3: Assemble the drawers as shown using hardware parts A, C, M, R1, R2, X and W with a screwdriver
(not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 4: Attach hardware parts Q1 and Q2 to the right panel (2) and division panel (3) using hardware part D,
then attach hardware parts N2 to the right panel (2) using hardware part E. You will need to use screwdriver
(not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 5 of 9
Step 5: Attach the hardware part P to the upper front frame (10) using a small mallet (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 6: Attach hardware parts N1 to the door (14) using hardware part B and a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 7: Attach the lower front plinth (11) to the base panel (8) using hardware parts L and W with a
screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 6 of 9
Step 8: Attach the upper front frame (5) and upper back frame (6) to the division panel (3) using hardware
parts M and W with a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 9: Attach the left panel (1) to the assembled division panel frame and the lower back frame (7) using
hardware parts F, G, L, S, U and W with a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 7 of 9
Step 10: Attach the lower back plinth (12), base panel (8) and upper front frame (10) to the division panel (3)
using hardware parts L and W with a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 11: Insert the back panel (19) then attach the right panel (2) using hardware parts L and W with a
screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 8 of 9
Step 12: Attach the top panel (4) using hardware parts C, L, M and W with a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 13: Insert the shelf panel (9) using hardware part T and a small mallet (not provided) Attach hardware
part Y to the door (14) then attach to the right side panel (2) using a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim

Vendor: S000180
Page 9 of 9
Step 14: Insert the assembled drawer to the frame and adjust the door as shown if necessary
DO NOT use any power tools as this may damage the frame and will invalidate any laim
Step 15: Secure the back panel (19) in place using hardware parts B and V with a screwdriver (not provided)
DO NOT use any power tools as this may damage the frame and will invalidate any laim
For complete product information, images and dimension
diagrams please visit www.birlea.com