Bishamon Multi Lift MUS40U User manual

Nov.2021
Sugiyasu Corporation
Dear Users,
Thank you for purchasing our Bishamon Multi lift. Before using the lift, read through and be
familiar with this manual. Fully understand the precautions, directions, and other
information contained in this manual to ensure correct use. Failure to do so may result not
only in insufficient performance of the lift but also in falling of the vehicle, serious injury and
death, and damage to properties.
Keep this manual in a safe place for future reference. In case of loss, immediately request a
new copy.
If the product is supplied with a wrong manual, contact your lift supplier for a correct copy.
Perform periodic maintenance inspection of the lift to ensure safe work
with the lift and keep the lift fully functional.

The contents of the manual may differ when the purchased lift is modified. For any
question about the product or this manual, feel free to contact your lift supplier.
Keep this manual in a safe place for future reference. In case of loss, contact your
lift supplier and request for a new copy immediately.
Thank you for purchasing our Bishamon Multi Lift . Before using the lift, read through
and be familiar with this manual. Fully understand the precautions, directions, and
other information contained in this manual to ensure correct use. Failure to do so may
result not only in insufficient performance of the lift but also in falling of the
vehicle, serious injury and death, and damage to properties.
In this manual, 「Danger」,「Warning」, 「Caution」are defined and
specified as below. Notice of Warnings are very important for safe operations. As
these are very Important to protect operators from accidents resulting in
personal injury and death, and damage to property, so make sure to read
thoroughly and understand fully before operation.
Danger
Incorrect operation may imminently result in serious
injury or death of the operator.
Warning Incorrect operation may result in serious injury or
death of the operator.
Caution Incorrect operation may result in injury and damage
to the property. The occurence of the danger is lower
than "Warning" articles.
Explanation of Terms and Symbols

1)
2)
3)
3) ～6)
7)
8) ～9)
10) ～12)
10)
11)
12)
13)
14)
15) ～16)
15)
16)
17) ～19)
20)
21) ～24)
25) ～28)
17)
29)
29) ～30)
31)
32)
33)
34)
35)
36)
36)
37)
38)
38)
38)
39)

This product is a lift to be used for oil and parts replacement, general maintenance,
motor vehicles inspection and maintenance etc. of mini-to ordinary sized passenger cars,
small sized trucks, and the like.
As there are very important to protect operators from accidents which may result in
injury and death,and damage to cars and properties, make sure to understand fully before
operating the lift.
1. Read and be familiar with the operation manual before operating.
2. Only trained operators are allowed to use the lift.
3. Make sure to perform daily and periodic inspections in accordance with the
instructions of Operation Manual.
4. If any abnormal conditions, such as noise, occur during operation, prohibit the
use of the lift and contact lift supplier for an inspection.
5. This lift is designed for motor vehicle servicing. DO NOT use for any other
purposes.
6. Do not remove any labels and do not modify the lift anyway.
The meaning of the mark (symbol) used behind pictures are as below.
When lift is operating,
get under the vehicle.
allow others to get under vehicle
Or it may result in death or serious injury.
attempt to support vehicle.
Or it may result in death or serious injury.
If the
Caution for Safety
The specified act
that should not be
conducted.
The specified act
that should be
conducted.
Warnings and
cautions that are
possible to occur due
to incorrect operation.

Read the Operation Manual DO NOT lower the lift
thoroughly before using while any stand or and parallel to the lift.
the lift. support is in position
Important Warnings are under vehicle. evenly.
described. DO NOT use "Down" motion
*Incorrect operation may of lift to push parts
result in an accident. into position.
Set the supporters on a DO NOT lift vehicles by DO NOT modify any Safety
flat spot with sufficient one end only. Or it may Device of the lift under
strength. Or supporters result in fall of the any circumstances.
may come off and vehicle vehicle and damage lift.
may fall.
KEEP FEET CLEAR Apply parking brake and
When lowering lift, make position wheel stop when evenly. DO NOT lift up
sure to keep feet clear operating lift. offset vehicle. Or it may
of hoist and vehicle. result in fall of vehicle
DO NOT use lift unless ELECTRICAL HAZARD!
you have been trained in when raising and lowering DO NOT open control box
it's operation. lift, MAKE SURE to keep or remove cover plates
*Incorrect operation may hands and feet clear of without isolating
result in an accident. any scissor mechanism. electrical supply.
Drive in vehicle straight
Vehicle MUST BE positioned
KEEP HANDS and FEET CLEAR
Vehicle MUST BE positioned

1. This lift is designed for motor vehicle servicing. DO NOT Use for other purpose.
2. If any of safety device does not work properly, DO NOT use lift.
3. Drive in and out vehicle slowly, and DO NOT start and stop suddenly.
5. When using Swing Board Supporter, make sure to grab handle for storing Supporter to avoid hands
and fingers from being caught and pinched.
1. When operating the lift, pay constant attention to the area around the vehicle and the lift.
NEVER look aside during operation.
2. If there are other lifts installed in the same site, Pay attention not to operate the control
switch of other lifts.
3. DO NOT lift up any vehicle exceeding the maximum capacity of the lift.
4. DO NOT lift vehicles with passengers, baggage or cargo etc.inside.
5. Use only genuine Side Sill Block supporter between upper lift top plate and vehicle lifting
point when lifting vehicle by upper lift.
6. Make sure there is no oil or dirt on supporter when lifting vehicle by upper lift.
7. Stop lifting after supporter have made firm contact with vehicle, and check locations of
supporter for correct lifting points before reraising the vehicle.
8. Stop lifting when lift reached maximum height.
9. During lift lowering operation, wait about 2 seconds before proceeding next lowering operations
10. The lift height of both sides may become unbalanced during lifting and lowering operations.
In such case, follow the instructions of Operation Manual and balance the height of both sides.
If not correcting the unbalance situation, it may result in the fall of the vehicle.
11. If the Jacking Beam is used with Pit Installation Model, DO NOT lower the Lower Lift below
350mm height. Make sure to slide and stow the Jacking Beam into hangar before relowering
lift to floor.
12. If the lift would not lower, raise the lift and then relower.
13. Make sure lift and lift supporters are fully lowered before driving in or out vehicle.
14. Before lowering the lift, ensure that no person or objects is around vehicle or lift.
15. DO NOT operate the lift with anything such as tools or parts left in the pit or under the lift.
Failure to comply may result in failure of the lift or falling of the vehicle.
16. When use Upper Lift, make sure to lift up to max height to avoid unbalance.
1. Make sure Safety Hooks are engaged before getting under vehicle.
2. When working on a vehicle in raised position, make sure the lift is above the position that
Safety Hook is engaged at least with 1st ratchet (Cut out) from the bottom. The lift may drift
down (Natural Lowering), causing damage to the vehicle or equipment,tools, or the like nearby.
3. Keep anyone but the operator out from around the lift.
4. DO NOT leave a vehicle on the lift for long time.
5. When not in use, the lift must be lowered to the lowest position.
6. When vehicle tyres are in free (neutral) position, make sure to set side brake, and put 2ea.
tyre stopper in front and rear of rear tyres.
7. After vehicle servicing work, lower the lift to bottom and turn off the power.
4. Pay attention in driving in and out vehicle when tires and drive-on plate are wet to avoid slipping.

1. DO NOT modify the lift without permission from the manufacturer. Failure to comply
may result in insufficient performance of the lift and lead to serious accident.
2. When an abnormality is detected during use or inspection, stop the use of the lift
immediately and repair. DO NOT use lift until the repair is completed.
3. This lift is not weatherproof and is not to be used outdoors or for vehicle washing.
4. Do not supply air with air pressure exceeding 1.0 MPa to the air filter regulator.
Or it may damage the air filter regulator.
5. The air filter regulator must be set to 0.7 Mpa. If it is set to over 0.7 Mpa.
Or it may damage the Selex Valve.
1. Perform measuring alignment within load capacity and applicable vehicle.
Refer to Page 25 『 Levelling Accuracy When Measuring Alignment 』
2. When Driving-In and Driving-Out the vehicle, make sure to insert fixing pin into
Turning Radius Gauge and Slip Plate.
If Driving-In and Driving-Out without fixing pin inserted, it may damage Turning
Radius Gauge and Slip Plate.
Refer to Page 27 『 Cautions on Alignment Servicing 』
3. Drive in the vehicle straight on the Drive-On Plate towards the center of Drive-On
Plate without deviation of the vehicle. And park the vehicle so that front tyres
position on the center of Turning Radius Gauge.
4. Do Not aggressively start, braking, turning on the Drive-On Plate.
Or it could lead to damage of the lift and vehicle.
5. When vehicle tyres are in free (neutral) position, make sure to set side brake,
and put 2ea.tyre stopper in front and rear of rear tyres.
Or it may result in the fall of the vehicle.
6. When lowering the lift to lowest, make sure the pointer of Turning Radius Gauge
is not outside of the lift before lowering the lift.
Or gauge may hit the pit and damage the Turning Radius Gauge.
7. The lift height of both sides may become unbalanced when lifting after servicing
vehicle. (This is not abnormal symptom). In such case, follow the instructions
of Operation Manual, and rectify the unbalance between right and left side Drive-On
Plate.
→ Refer to Page 25 『 Rectifying the Levelling in Alignment Servicing 』

Capacity Label
Caution Label B Serial Plate
CG Label
Capacity Label
Capacity Label
Caution Label B
Serial
Plate
Serial
Plate
Caution Label A
CG Label
Capacity Label
Hyd. Unit
There are important warnings, cautions, lift capacities and instructions etc. described in the labels
to avoid serious accidents and damage to the properties. If labels are worn, damaged or peeled
off, purchase replacement labels immediately and stick on the specified spot.

No Mark : Standard Drive-On Plate
L : 500mm Extended Drive-On Plate
U : Built-In Hyd. Unit
S : Hyd. Unit Installed Separate
No Mark : General Repair & Servicing
H : Alignment Servicing
40 : 4,000 kg

When pushing the Button, Drive-On Plate
lowers to the closest Lowering Stop Hook,
and Drive-On Plate would be locked.
When unbalance occurred between Right and Left
Drive-On Plate, unbalance can be adjusted by
pushing this Level Button and "Up"(or "Down")
button together at same time.
※ Left side Drive-On Plate from car entrance
direction rise or lowers.
By pushing, Upper Lift (Supporter) rise, or
lower. When releasing, Upper Lift stops.
By pushing, Lower Lift (Drive-On Plate) rise,
or lower. When releasing, Lower Lift stops.
Refer to Page 15, 19, 27 and 31
『 Lift up the Lower Lift (Drive-On Plate) 』
『 Lower down the Lower Lift (Drive-On Plate) 』
Upper Lift
Lower Lift
Lock
Level
Lock
Upper
Lower

When Drive-On Plate goes up, Wheel Stop automatically flap up.
Select the attachment depending on the lifting point of the vehicle
※ Refer to Page 37 for the optional Attachment and applicable vehicle.
.
The height info.is available height when Upper Lift is lowered to lowest
point is located outside of Upper Lift (Supporter).
Pull out the Slide Arm and install Attachment on it.
Air Filter Regulator reduce the air pressure of the
air supplied to the Air Filter Regulator to appropriate
gauge shows the air pressure after depressurization.
pressure levels, and drain water in the air. Air pressure
Swing Board Supporter can be used when vehicle lifting
The height info.is available height when Slide Arm of Swing Board on Upper Lift is used
Wheel Stop
Side Sill Block
Adjustable
Attachment Assy
Adjustable
Supporter D Assy Frame Attachment LB
(100 X 70 X 140)
Slide Arm
Attachment
Swing Board
Air
Pressure
Gauge
Pressure adjustment knob
Water Drain Valve
Min. 97mm
Max 118mm
Min. 129mm
Max 165mm
Min. 153mm
Max 218mm

Slip Plate is used for measuring the alignment
Turning Radius Gauge is used for measuring the
alignment.
If the lift is ordered with special Jacking Beam, Jacking Beam Pit Cover lift up and
down according to lifting up and lowering down of Flat Kit.
Front Filler Plate is used when Turning Radius Gauge
is not used.
Slip Plate
Turning Radius Gauge
Flat Kit Table
Jacking Beam Pit Cover
Front Filler Plate

Multi Lift is operated by Electro Hydraulic.
・Upper Side Lift - through hydraulic valve
・Lower Side Lift - direct connection of both side cylinders
When pushing "Up" button, motor runs and gear pump feed the oil to cylinder,
and lift goes up. And Lowering Stop Hook is 『 IN 』position. When releasing
the button, oil flow stops at Check Valve and lift (Cylinder) stops.
When pushing "Down" button, Lowering Stop Hook would be released first, then
Lowering Valve opens and lift goes down. When releasing the button, Lowering
Stop Hook engage and Lowering Valve close and lift stops.
Upper Lift and Lower Lift is to be switched by operating electric valve.
Because the lift is raised through hydraulic cylinder, lift is naturally to be lowering slightly.
Therefore the lift height can not be kept at same height for long time which should be noted.

It would sense the excessive electric current, and shut off
the electric circuit and protect motor burning.
※ Thermal Relay is installed in the Magnet Contactor.
※ Relief Valve is installed inside Manifold.
Fuse Valve would shut off oil flow from
cylinder in case of sudden flow of oil a. Lifting excessing rated lift capacity
from cylinder due to breakage of hydraulic b. Lift is reaching the top
hose and piping etc., and prevent Drive-On
Plate, Supporter and vehicle from falling.
It would prevent lift from break in case of below
c. Excessive high pressure in hydraulic line
Thermal
Relay
Thermal Relay
Hook device for protecting Drive-
On Plate
and Supporter from lowering when oil
leaks or hyd. hose broke.
Lowering Stop
Device (Rack)
Lowering Stop
Device (Hook)
Fuse
Valve (Shut Off Valve)
Relief
Valve
Fuse Valve (Shut Off Valve)
Relief Valve
Manual Lowering Valve
Lowering
Stop Device

Any damage, strain or distortion ? Visual
Does lift rise and lower smoothly without
noise ?
Is there any obstacles inside pit ?
Does Link and Shoe work properly ?
show 0.7 Mpa ?
Drain by Drain Valve
everyday ? Refer to Page 16
Any oil leak from Hyd. Unit ? Visual
Any abnormnal noise from Motor, Pump during
lifting and lowering ?
Any oil leak ? Visual and touching
Visual and touching
Does system operate without fail ?
Does safety device make "clicking" noise
during lifting operation ?
Are both Right and Left side Lowering Stop
Hook released without fail in lowering ?
Does Lowering Stop Hook engage at the top
with "clicking" noise ?
Are both Right and Left side Lowering Stop
Hook released without fail in lowering ?
Can all 8ea.leg be kept horizontal or
vertical position ?
Any damage on Turning Radius Gauge ? Visual
Does Wheel Stop work properly ? Visual
Wheel Stop
Link Mechanism and
Slide Shoe Visual
Lift Structure
Lift Visual and hearing
Visual and Adjust
Any damage on Hyd. Hose, air hose and piping ?
Hydraulic Cylinder
and Piping
Lowering Stop Device
on Lower Lift
Visual and hearing
Visual and hearing
Is water drained from Air Filter Regulator
Visual and hearing
Any abnormality in Air and Electrial System ?
Air and Electrial System Visual and hearing
Hydraulic Unit
Does Pressure Gauge of Air Filter Regulator
Operation
(Only Model MUL30H)
Remote Control Switch
and Flexibile Cable Any damage, wear ? Visual
Visual and hearing
Visual and hearing
Lowering Stop Device
on Upper Lift
If any possible abnormality is detected, prohibit the use of the lift until abonormality is
fully repaired. Then contact your lift supplier immediately. If the lift is used with
abnormality left unsolved, damage to the lift or serious accident may occur.
Caution

Air Filter Regulator reduce the air pressure of the air supplied to Air Filter Regulator
gauge shows the air pressure after depressurization.
① Verify that the air pressure supplied to the
Air Filter Regulator is more than 0.5 Mpa
② Loosen the screw on top of the Air Filter
Regulator.
③ Look at and check the air pressure gauge while
turning the pressure adjustment knob to set the
air pressure to 0.5 Mpa.
④ Tighten the screw on the top of Air Filter
Regulator.
① Push up the drain valve at the bottom.
Water sprays out with air.
to appropriate air pressure levels (0.7～1.0MPa), and drain water in the air. Air pressure
Depressurize Pressurize
Pressure
adjustment knob
Air pressure
gauge
Screw
*The appropriate value of the pressure of air (primary side pressure) supplied to the filter
regulator is between 0.7 and 1.0 MPa. The filter regulator could be damaged if the
pressure is greater than 1.0 MPa.
* Always make sure that the air pressure gauge is pointing 0.7 MPa before operating lift.
The lift may malfunction if the pressure is under 0.5 MPa. Furthermore, the Selex valve
may be damaged if the pressure is over 0.7 MPa. Always set the pressure to 0.7 MPa.
Caution
Drain valve
Drain water must be drained from the air filter regulator every day.
Accumulation of water can cause malfunction.
Caution

Lower the lift (including Upper Lift) to the lowest (floor LeveL) by pushing
"Down" button of Lower lift so that Drive-On Plate and Floor Level becomes same.
Refer to Page 21, 『 Lifting Operation of Upper Lift 』.
① For Alignment Model (MUS40HU & HUL), Make sure to insert Fixing Pin for the
Turning Radius Gauge and Slip Plate.
② Drive in vehicle parallel to the Drive-On Plate of the lift and evenly in its
width direction, and stop (park) the vehicle on the spot where Front Wheels
and Rear Wheels are located well balanced. Also pay attention in stopping
(parking)vehicle so that vehicle tyres are not hitting Supporter.
※ Applicable Vehicles - Passenger car, SUV, Light Truck (except Long body truck)
・DO NOT lift up vehicle which is heavier than lift capacity.
・DO NOT lift up vehicle with passengers or baggage inside.
・Drive in and out vehicle slowly, and DO NOT start and stop vehicle suddenly.
・Drive carefully when tyres or Drive-On Plate are wet to avoid slipping.
・Make sure Drive-On Plate and Upper Lift are lowered to lowest before driving in
or driving out vehicle

① Push "Up" button of Lower Lift. When pushing, lift keep rising.
② When Drive-On Plate reached required height, release the button.
Lift would stop.
① Push "Down" button of Lower Lift. When pushing, lift keeps
lowering
② When Drive-On Plate reached required height, release button.
Lift would stop.
･When lift reached the max height, STOP lifting immediately.
･DO NOT leave the lift for long time without attendance after lifting up vehicle. At the lower
height level where there is no Lowering Stop Rack, lift could lower and damage the vehicle
if lift is left over without attendance.
UP
Down
Lower Lift
Lower Lift
Down
UP
･DO NOT leave the lift for long time without attendance after lowering lifthalfway . At the
lower height level where there is no Lowering Stop Rack, lift could lower and damage the
vehicle if lift is left over without attendance.
･If Lowering Stop Rack can not be released and lift does not lower, lift up slightly and then
lower the lift.
･DO NOT push "Up" button just after pushing "Down" button. If "Up" button is pushed just
after pushing "Down" button, Lowering Valve could be kept open, and lift may keep
lowering. Make sure to wait 1 to 2 seconds before pushing "Up" button. This symptom is
normal.

① Before lowering the lift to the lowest, move Jacking Beam to Storage Spot.
※ Storage Spot is the spot of Jacking Beam Pit Cover, and located at front
and rear of the lift. There are Jacking Beam Stoppers at Front and Rear
side end of Drive-On Plate. Make sure to move Jacking Beam until Jacking
Beam hit the Stopper.
① Make sure Supporter of Upper Lift is lowered to lowest
② For Alignment Model (MUS40HU & HUL), Make sure to insert Fixing Pin for the
Turning Radius Gauge and Slip Plate.
③ Drive out vehicle slowly
If trying to lower the lift to lowest before moving Jacking Beam to Storage Spot, it
could damage the lift and Jacking Beam.
DO NOT start or stop vehicle aggressively on the Drive-On Plate. Or it could result in
damage to the lift and serious accident.