Bishamon ESC32UF User manual

Sugiyasu Corporation
Nov. 2020
Dear Users,
Thank you for purchasing our Bishamon Status lift. Before using the lift, read through and
be familiar with this manual. Fully understand the precautions, directions, and other
information contained in this manual to ensure correct use. Failure to do so may result
not only in insufficient performance of the lift but also in falling of the vehicle, serious
injury and death, and damage to properties.
Keep this manual in a safe place for future reference. In case of loss, immediately request
a new copy.
If the product is supplied with a wrong manual, contact your lift supplier for a correct copy.
Perform periodic maintenance inspection of the lift to ensure safe work
with the lift and keep the lift fully functional.

The contents of the manual may differ when the purchased lift is modified. For any
question about the product or this manual, feel free to contact your lift supplier.
Keep this manual in a safe place for future reference. In case of loss, contact your
lift supplier and request for a new copy immediately.
Thank you for purchasing our Bishamon Status lift. Before using the lift, read through
and be familiar with this manual. Fully understand the precautions, directions, and
other information contained in this manual to ensure correct use. Failure to do so may
result not only in insufficient performance of the lift but also in falling of the
vehicle, serious injury and death, and damage to properties.
In this manual, 「Danger」,「Warning」, 「Caution」are defined and
specified as below. Notice of Warnings are very important for safe operations. As
these are very important to protect operators from accidents resulting in
personal injury and death, and damage to property, so make sure to read
thoroughly and understand fully before operation.
Danger
Incorrect operation may imminently result in serious
injury or death of the operator.
Warning Incorrect operation may result in serious injury or
death of the operator.
Caution Incorrect operation may result in injury and damage
to the property. The occurence of the danger is lower
than "Warning" articles.
Explanation of Terms and Symbols

1)
2)
3)
3) ～ 5)
6)
7)
8)
9)
9)
9)
10)
10)
11)
12)
13)
13)
14)
15)
15)
15)
16)
17)
18)
18)
19)
20)
20)
21)
22)
23)
23)
24)
25) ～ 26)
27)
28)
28)
29) ～ 30)
30)
30)
30)
31)

This product is a lift to be used for oil and parts replacement, general maintenance,
motor vehicles inspection and maintenance etc. of mini-to ordinary sized passenger cars,
small sized trucks, and the like.
As there are very important to protect operators from accidents which may result in
injury and death,and damage to cars and properties, make sure to understand fully before
operating lift.
1. Read and be familiar with the operation manual before operating.
2. Only trained operators are allowed to use the lift.
3. Make sure to perform daily and periodic inspections in accordance with the
instructions of Operation Manual.
4. If any abnormal conditions, such as noise, occur during operation, prohibit the
use of the lift and contact lift supplier for an inspection.
5. This lift is designed for motor vehicle servicing. DO NOT use for any other
purposes.
6. Do not remove any labels and do not modify the lift anyway.
The meaning of the mark (symbol) used behind pictures are as below.
When lift is operating,
get under the vehicle.
allow others to get under vehicle
Or it may result in death or serious injury.
If the
attempt to support vehicle.
Or it may result in death or serious injury.
Caution for Safety
The specified act
that should not be
conducted.
The specified act
that should be
conducted.
Warnings and
cautions that are
possible to occur due
to incorrect operation.

Read the Operation Manual DO NOT lower the lift
thoroughly before using while any stand, jack or and parallel to the lift.
the lift. support is in position
Important Warnings are under vehicle. evenly. And set the CG of
described. DO NOT use "Down" motion vehicle within the range
*Incorrect operation may of lift to push parts
result in an accident. into position. arrow on the lift.
Set the supporters on a DO NOT lift vehicles by DO NOT modify any Safety
flat spot with sufficient one end only. Or it may Device of the lift under
result in fall of the any circumstances.
Side Sill Block supporters vehicle and damage lift.
to avoid any accident.
KEEP FEET CLEAR
When lowering lift, make the raised vehicle. Or it evenly. DO NOT lift up
sure to keep feet clear may result in fall of the offset vehicle. Or it may
of hoist and vehicle. vehicle. result in fall of vehicle
DO NOT use lift unless ELECTRICAL HAZARD!
you have been trained in when raising and lowering DO NOT open control box
it's operation. lift, MAKE SURE to keep or remove cover plates
*Incorrect operation may hands and feet clear of without isolating
result in an accident. any scissor mechanism. electrical supply.
KEEP HANDS and FEET CLEAR
specified with Yellow Color
DO NOT swing, shake or push
strength. Use only genuine
Vehicle MUST BE positioned
Vehicle MUST BE positioned
Drive in vehicle straight

1. This lift is designed for motor vehicle servicing. DO NOT Use for other purpose.
2. If any of safety device does not work properly, DO NOT use lift.
3. Drive in and out vehicle slowly, and DO NOT start and stop suddenly.
5. Adjust the height of supporters to evenly distribute the load among the 4 supporters when using
the Swing Arm.
6. Set the supporters securely at lifting points, and do not raise a vehicle when there are not
of correct lifting points.
1. When operating the lift, pay constant attention to the area around the vehicle and the lift.
NEVER look aside during operation.
2. If there are other lifts installed in the same site, Pay attention not to operate the control
switch of other lifts.
3. DO NOT lift any vehicle exceeding the maximum capacity of the lift.
4. DO NOT lift vehicles with passengers, baggage or cargo etc.inside (on board).
5. Make sure there is no oil or dirt on supporter when lifting vehicle.
6. Stop lifting after supporter have made firm contact with vehicle, and check locations of
supporter for correct lifting points before reraising the vehicle.
7. The lift height of both sides may become unbalanced during lifting and lowering operations.
In such case, follow the instructions of Operation Manual and balance the height of both sides.
If not correcting the unbalance situation, it may result in the fall of the vehicle.
8. If the lift would not lower, raise the lift and then relower.
9. If lower the lift with Sliding Supporter being used (extended), retract Sliding Supporter back
when vehicle tyre hit the floor, and then lower the lift to lowest position. Or Supporters and
floor could be damaged.
10. Before lowering the lift, ensure that no person or objects is around vehicle or lift.
11. DO NOT operate the lift with anything such as tools or parts left in the pit or under the lift.
Failure to comply may result in failure of the lift or falling of the vehicle.
1. Make sure Safety Hooks are engaged before getting under vehicle.
2. Keep anyone but the operator out from around the lift.
4. DO NOT leave a vehicle on the lift for long time.
5. When not in use, the lift must be lowered to the lowest position. Even when not in use, raise
and lower the lift all the way through the range at least once a day to maximize the lift life
6. When lowering the lift of Alignment Model(MUL30H), make sure to set all 8 legs are folded or
set(fixed) firmly. If the legs are not set firmly, or floor conditions are not flat, the legs
might get out of place, and dangerous.
7. After vehicle servicing work, lower the lift to bottom and turn off the power.
1. DO NOT modify the lift without permission from the manufacturer. Failure to comply may result
in insufficient performance and lead to serious accident.
2. When an abnormality is detected during use or inspection, stop the use of the lift immediately
and repair. DO NOT use lift until the repair is completed.
3. Use only genuine Side Sill Block supporter.
4. This lift is not weatherproof and is not to be used outdoors or for vehicle washing.
5. Do not supply air with air pressure exceeding 1.0 MPa to the air filter regulator. Or it may
damage the air filter regulator.
6. The air filter regulator must be set to 0.7 Mpa. If it is set to over 0.7 Mpa, it may damage
Air Switching Valve.
Drive the vehicle in and out only after the swing arms have been opened completely. Failure to
do so can cause damage of the vehicle or the lift.
4. Pay attention in driving in and out vehicle when tires and drive-on plate are wet to avoid slipping.
clear lifting points on the vehicle. Refer to the maintenance manual of the vehicle for information
7. Drive the vehicle in and out only after the supporters and Flat Kit have been lowered completely.

CG Label
CG Label
Caution Label
Capacity Label
Capacity Label
Serial Plate
Labels feature descriptions on important matters for preventing accidents and property damages,
as well as capacity of the lift. Purchase and apply these lables promptly when they become worn,
damaged or peeled off while the lift is used.

Sliding Supporter
Sliding Supporter
Swing Arm
Hyd. Unit
Flat Kit
Storage Box
Control Switch
Air Filter
Regulator
Control Box
Upper Sub Cylinder
(S Cylinder)
Upper Main Cylinder
(M Cylinder)

Level
Lift Arm
Lift Arm
Left Right
Seeing from car entrance direction, Left side supporter rise up and lowers down.

Air Pressure
Gage
Pressure
Adjustment Knob
Drain Valve

Thermal Relay
Lowering Stop Device (Hook)
Lowering Stop
Device (Rack)
Relief Valve
Fuse Valve (Shut Off Valve)
Thermal Relay sense the excessive electric
current and shut off the citcuit and protect
motor from burning. Thermal Relay is
installed at magnet contactor.
Lowering Stop Device are installed at each
cylinder to prevent lift from lowering in
case of oil leaking and breakage of hydraulic
hoses etc.
Fuse Valve is installed at each cylinder, and
shut off the oil flow in case sudden flow of
oil from cylinder due to the breakage of
hydraulic circuit etc., and prevent vehicle
from falling.
Relief Valve would release hydraulic pressure
to protect lift from breakage in case below.
1) Lifting heavier load than lift capacity
2) Lift is reaching the max height
※ It is installed at manifold in the
hydraulic unit of lift center.

Depressurize Pressurize
Pressure
adjustment knob
Air pressure
gauge
Screw
*The appropriate value of the pressure of air (primary side pressure) supplied to the
air filter regulator is 0.7 ～1.0 MPa. The air filter regulator may be damaged if the
pressure is greater than 1.0 MPa.
* Always make sure that the air pressure gauge is pointing 0.7 MPa before operating
lift. The lift may malfunction if the pressure is under 0.7 MPa. Furthermore, the Selex
Valve may be damaged if the pressure is over 0.7 MPa. Always set the pressure to
0.7 MPa.
Caution
Drain valve
Drain water must be drained from the air filter regulator every day.
Accumulation of water can cause malfunction.
Caution

Lower the lift to lower limit, and store the Swing Arms into Swing Arm Case. If
Swing Arms are not stored in the case, vehicle may hit the Supporter and Swing
Arms and could result in damage to the lift and vehicle.
If the lift does not lower to lower limit by pushing Lowering button, it is possible
Upper Lift is not lowered to lowest. In that case, refer to Page 18 " 7-6 Lowering
Operation " and raise Upper Lift 100mm and then lower again.
Caution
●Make sure to park the vehicle so that CG of the vehicle stay within the range
shown in Yellow Color Arrow on the side of the Supporter. If not, vehicle may
fall due to the vibration during lift operation and vehicle servicing.
●When driving in vehicle, pay close attention lest vehicle tyre should hit Frame
Attachment and Swing Arms.
Caution

●Make suer to use Lifting Point car manufacturer designated, and do not use
other spot of the vehicle for lifting up. Using other spot may result in
unbalance of the vehicle and damage vehicle. Do not lift up if the Lifting Point
is not clear.
●DO NOT lift up only one side end in front, rear, or right and left.
●Set the Supporter to support the correct Lifting Point firm. If not, Supporter
may come off and vehicle may fall.
Warning
●Make sure to set Support Pad to flat and stable lifting point of the vehicle. If set
to unstable lifting point, vehicle may lose balance and could fall.
●Adjust the height of Support Pad so that vehicle load can be distributed evenly
on 4ea. Support Pads. If not, Support Pads may come off and vehicle could fall.
Warning
Make sure to perform operation of Lifting Up Swing Arm only when lift unit is
lowered at its lowest position.
Caution
When lifting by Swing Arms, try to spread (open) arms as wide as possible.
Caution

NEVER go and stand under the vehicle during lift operation.
Danger
・DO NOT lift vehicles with passengers, baggage or cargo etc. inside (on board).
・When operating the lift, NEVER look aside, and pay constant attention to the
area around the vehicle and the lift, or it could result in serious accident.
Warning
DO NOT lift any vehicle exceeding the max lift capacity. Or it may damage the lift.
Caution
Floor
・DO NOT stop and leave Flat Kit in the halfway.
・As Flat Kit does not have Lowering Stop Device installed like upper Lift Unit,
stop Flat Kit either at max height, or at lowest position if servicing work is
suspended.
Caution
Flat Kit

・DO NOT shake the raised vehicle hard. The Supporter Pads could come off and
vehicle could fall.
・Pay close attention when removing or installing heavy parts to prevent the
vehicle from falling. Balance could be lost and vehicle could fall.
Warning
NEVER go and stand under the vehicle during lift operation.
Danger
・DO NOT lower the lift while any stand, jack or support is in position under vehicle.
DO NOT use 『DOWN』motion of lift to push parts into position. Vehicle could
fall.
・DO NOT put foot under Supporter. Or foot could be pinched and serious injury
could result.
Warning
If lift does not lower when pushing 『DOWN』button, lift up once, and then lower
the lift again.
Caution
Floor
Flat Kit
・DO NOT stop and leave Flat Kit in the halfway. As Flat Kit does not have
Lowering Stop Device installed like upper Lift Unit, stop Flat Kit either at max
height, or at lowest position if servicing work is suspended.
・DO NOT leave the lift with a vehicle lowered halfway unattended for a long time.
A vehicle left on the lift at a low position without engaging Lowering Stop Hook
could cause the vehicle to be lowered and damaged.
・When the upper lift (M. side) was lowered to lowest floor level and lift stopped,
release 『DOWN』button. Flat Kit does not start lowering until upper lift is
lowered to lowest. But if releasing 『DOWN 』button at around lowest position,
Flat Kit start lowering with upper lift still not folded completely.
Upper Lift
Caution

・Check and make sure the lift is lowered to the lowest. If the lift is left at midway,
it could result in damage to the lift and vehicle.
・If the Sliding Supporter is not retracted (stored back), it could result in the
damage to the lift and vehicle.
Caution
・After vehicle servicing work, push Slide Arm back into Swing Arm completely
(retract), and lower the lift to lowest position. If lift is lowered with Slide Arm not
being retracted completely, Slide Arm could be stranded on the floor and could
damage Arm Pin.
Caution
Lift arm Sliding arm
Store
Rotate
Frame attachment
Swing arm