Bitspower BPTA-SBSKIT-SA User manual

P 1
BPTA-SBSKIT-SA Installation Guide
English
V1
1 2 3 4 5 6 7
8
12
10
11
14
16
9
A
B
G
C
D
E
F
13
15
Accessories
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
...............1 PC
...................2 PCS
...1 PC
..2 PCS
.................1 PC
....1 PC
.......1 PC
...............1 SET
.1 SET
Radiator
Fan
Radiator mount bracket
Water tank mount bracket
Pump
Water tank system
CPU water block
Fittings
(See following details)
Other accessories
(See following details)
H. Fittings I. Other Accessories
.......6 PCS
...........1 PC
...........1 PC
......1 PC
.......1 PC
........1 PC
........1 PC
TA-CFS3858-GB
BPTA-F06-GS
TA-TRC-GS
BPTA-EFW-V2-GS
BPTA-EXAIR-GS
BPTA-90RE-GS
BP-BB2WP-P02
................1 PC
.....1 SET
.............1 PC
...........1 PC
.......1 PC
..1 PC
..........1 PC
................2 PCS
............1 PC
Soft tube
CPU backplane set
Y wire(Fan)
Y wire(DRGB)
Fitting nut wrench
DRGB Multi Function Controller
Thermal grease
Coolant
BP-PSC-SOC
Other accessories
H
Fittings
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
A
D
C
B
E
F
G
H
I
I

P 2
Alternative build

P 3
1Install the water tank flap
Install the fans and reservoir on the radiator
2
M4 Nut
M4x10 Screw
M4x6 Screw
M4x30 Screw
1
C
D
B
A
Soft tube installation warning
！
Soft tube installation steps:
1. Pull the fitting apart by unscrewing the
sleeve from the nut.
2. Slide the tube through the sleeve then push
the tube over the nut head until the end.
3. Lock the nut tightly to the sleeve using a
clockwise rotation.
Pump Spec.
Rated voltage：12V DC
Power consumption：8.4W
Maximum flow：460±15%L/h
Noise：≦24dBA
PWM：Yes
MTBF：≦15,000 hours
Warranty：2 years
1
6
The water tank base and water pump should not be disassembled.
Disassembly will void the warranty.
A Negative electrode -
B positive electrode +
C Speed signal
D Speed control signal
A B C D
Digital RGB PIN on motherboard or other equipment.
 
motherboard DRGB Multi Function Controller
13
1
5
3
4
E
1
8
12
F
CLOSE
OPEN
Connect to motherboard.

Connector direction in connection
This connector can be on the...
FAN
PUMP
Choose the speed what you need
Select the connector with label number J1 and color BLACK,
which will let you operate at LOW speed .
Select the connector with label number J2 and color WHITE,
which will let you operate at FULL speed .
24pin
BP-PSC-SOC
P 4
14
Apply block over AMD CPU
Install the CPU
3
Wire
4
Connect the Addressable RGB（+5V）Light
Installation 1
Please closely follow this diagram for installation.
96
90
48 54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
DRGB LED
INOUT
M3x32mm SCREW
1mm SPACER
Back Pad
3M Paste Pad
Metal Backplane
SCM3FL20
SPRING
CPU Block
CPU Block PLATE(AM4)
1mm SPACER
SCM3F6
Use an appropriate amount
of thermal paste.
Digital RGB PIN on motherboard or other equipment.
 
motherboard DRGB Multi Function Controller
PWM
FG
+
−
PWM
FG
+
−
PWM
+
−
Master
Slave
13
11
10
16

P 5
Optimum water route
Install the tube with fitting
5
1
1

Water
6
Pour the coolant into the reservoir via the water filling hole. Once the reservoir is 90% full, turn on the power supply for the pump to run and let the air
exit the loop. Turn off the power supply when the reservoir is near empty. Repeat until all the air has exited the loop.
Notice:
Bitspower recommends that consumers add the Bitspower coolant or purified water for
their water-cooling liquid. If the consumer chooses different water-cooling liquids, the
resulting impurities may cause peeling of the coating on some of the hardware, water
channels blockage by built-up residue, improper operation of the water pump, water
tank tube breakage, and o-rings deformation leading to leakage. Any issues related to
the use of inappropriate water-cooling liquid will be the responsibility of the consumer.
Do not turn on the pump if the reservoir is empty.
Digital RGB Multi Function Controller
7
Power
DRGB
Mode+ Mode-Speed
The DRGB controller is used to expand the amount of DRGB header of the motherboard. The controller can expand one DRGB header into eight, and control
multiple fans and LED strips compatible light effects controlled by the motherboard. In addition, the controller has its own lighting effects, which can be
controlled by the buttons found on the controller.
ATTENTION:
1: The controller can't increase the power supply of the DRGB header from the motherboard. A standard DRGB header can provide 5Vx1A=5W of power.
It is recommended that the combined length of the LED strip connected to the controller be shorter than 1 meter. If the DRGB header is overloaded, the
brightness of the light will be reduced considerably. To restore the brightness, some items plugged to the controller must be removed.
2: Connection tip - Keep in mind that the arrow marks on the connector corresponds to 5V pin for the DRGB headers.
3: When using the controller separately, please connect to a SATA port only.
Specifications:
Operating voltage: DC 5V input
Power: Less than 1W
◆Press MODE+ and MODE- buttons simultaneously
and release at the same time to enter auto mode.
Water filling hole
P 6
motherboard
Drain
7
Connect the tube
◆To avoid short circuit, please cover the unused
headers with a plastic cover or electrical tape.