Bitspower BPM-VG4090MSR User manual

[ 1 ]
Bitspower Nebula VGA Water Block for
MSI GeForce RTX 4090 SUPRIM and GAMING series
instruction manual
V1
1
GPU
(Not included)
Step 1 Step 2
Step 4Step 3
Accessories
1
2M2.5 x 8 Screw1
BPM-VG4090MSR 1 SET
3M2.5 x 6 Screw 2 PCS
11 PCS
1 Two screws fastened in advance.
2
2
4
4
Before installing the graphics
card, please make sure that
the GPU has been coated with
thermal paste. In addition, please
tear off the films on the thermal
pads of the water block.
4Backplate 1 PCS

[ 2 ]
instruction manual
Step 5
motherboard
DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
1
2
In Out
Digital RGB PIN on 1motherboard or 2
other equipment.
Original I/O(Not included)
Original screw(Not included)
Original bracket(Not included)
3
Accessories
1
2M2.5 x 8 Screw1
BPM-VG4090MSR 1 SET
3M2.5 x 6 Screw 2 PCS
11 PCS
1 Two screws fastened in advance.
4Backplate 1 PCS

[ 3 ]
instruction manual
Make sure the correct thermal pads are in the appropriate locations.
Use an appropriate amount of thermal paste.(Not Include)
1.0 mm Thermal pad 1.5 mm Thermal pad
Name Specification Quantity
2Thermal pad 6 93.8×19.5×1.5mm
6Thermal pad 5 8×12×1mm
3Thermal pad 4 13×16×1mm
6Thermal pad 3 14×50×1mm
4Thermal pad 2 6×52×1mm
1Thermal pad 1 15×37×1mm

[ 4 ]
Notice
Before 󽗉lling with water, please make sure all the components are installed correctly. To prevent any leakage
which may damage the PC components, please perform a 24-hour leak test with only the pump connected to
the power supply.
Bitspower reserves the right to change the product design and specifications. These are subject to change
without notice. Product colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product damage due to excessive pressure, the
input pressure should not exceed 0.5kg/cm2 (Bar). If the product is damaged due to excessive pressure, it will
be the fault of the customer. DO NOT use the leak teser when there is water in the loop or the pump is running.
Bitspower recommends that customers use Bitspower Pellucid Coolant for their coolant fluid. It is also
recommended to use Bitspower Dye to create any desired color. If the customer chooses different liquid
coolants, the resulting impurities may cause peeling of the coating on some of the hardware, water channel
blockage by built-up residue, improper operation of the water pump, water tank tube breakage, and o-ring
deformation leading to leakage. Any issues related to the use of inappropriate liquid coolants will be the
responsibility of the customer.

[ 5 ]
使用說明書
步驟 1 步驟 2
步驟 4步驟 3
配件
1 兩根螺絲預先鎖上
在安裝顯卡之前，請確保 GPU 已塗
上導熱膏。
另外，請撕下水冷頭導熱墊上的貼
膜。
1
GPU
( 不包括 )
1
2M2.5 x 8 螺絲 1
BPM-VG4090MSR 1 組
3M2.5 x 6 螺絲 2 支
11 支
2
2
4
4
4背板 1 片
Bitspower Nebula VGA Water Block for
MSI GeForce RTX 4090 SUPRIM and GAMING series
V1

[ 6 ]
3
使用說明書
步驟 5 進出
配件
原廠檔板 ( 不包括 )
原廠螺絲 ( 不包括 )
原廠支架 ( 不包括 )
主板
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
1
2
請接 1主板或 2 其他設備的 DRGB 插槽
1 兩根螺絲預先鎖上
1
2M2.5 x 8 螺絲 1
BPM-VG4090MSR 1 組
3M2.5 x 6 螺絲 2 支
11 支
4背板 1 片

[ 7 ]
使用說明書
導熱墊片的正確應用位置
1.0 mm 導熱墊片
適量使用導熱膏 ( 不包括 )
1.5 mm 導熱墊片
Name Specification Quantity
2Thermal pad 6 93.8×19.5×1.5mm
6Thermal pad 5 8×12×1mm
3Thermal pad 4 13×16×1mm
6Thermal pad 3 14×50×1mm
4Thermal pad 2 6×52×1mm
1Thermal pad 1 15×37×1mm

[ 8 ]
記得上角要放對應的 LOGO!
注意
跑水前，請先確認所有零件已安裝在正確的位置上，在不開主機，單開水泵的情况下，進行 24 小時的跑水測試，
確保無漏水情况後再開主機，避免發生漏水而導致電腦零件的損壞。
本公司保留對產品的設計更改以及解釋的權力，如有更動恕不另行通知，產品顏色與配件以實物為準。
當使用測氣產品測試水路時 , 為避免由于壓力過大導致產品損壞 , 輸入的壓力請不要超過 0.5kg/cm2 (Bar), 如因壓力
過大造成產品損壞 , 將由客戶自行承擔 . 嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。
Bitspower 建議消費者使用 Bitspower 透明冷卻液。此外，也可以添加 Bitspower 染料到透明冷卻液中以滿足顏色
要求。如果消費者選擇不同的水冷液，可能會引起水路配件中的塗層剝落、積垢堵塞水道、水泵磨損、水箱管破裂、
破壞 O 型圈密封性導致漏水等。任何因使用不當水冷液導致相關的問題將由消費者自行負責。

[ 9 ]
記得上角要放對應的 LOGO!
使用说明书
步骤 1 步骤 2
步骤 4步骤 3
配件
1 两根螺丝预先锁上
在安装显卡之前，请确保 GPU 已涂
上导热膏。
另外，请撕下水冷头导热垫上的贴
膜。
1
GPU
( 不包括 )
1
2M2.5 x 8 螺丝 1
BPM-VG4090MSR 1 组
3M2.5 x 6 螺丝 2 支
11 支
2
2
4
4
4背板 1 片
Bitspower Nebula VGA Water Block for
MSI GeForce RTX 4090 SUPRIM and GAMING series
V1

[ 10 ]
步骤 5
使用说明书
配件
3
进出
原厂档板 ( 不包括 )
原厂螺丝 ( 不包括 )
原厂支架 ( 不包括 )
主板
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
1
2
请接 1主板或 2 其他设备的 DRGB 插槽
1 两根螺丝预先锁上
1
2M2.5 x 8 螺丝 1
BPM-VG4090MSR 1 组
3M2.5 x 6 螺丝 2 支
11 支
4背板 1 片