Bitspower Summit M Pro User manual

[ 1 ]
Press and hold the button for three seconds in
order to switch the device's status.
Bitspower CPU Block Summit M Pro
with OLED (12th Gen Intel CPU)
instruction manual
Digital RGB PIN on 1motherboard or 2other equipment.
motherboard DRGB Multi Function Controller
(Not included)
BPTA-DRGBMFC
12
V1
80
75
72
INTEL LGA 775 INTEL LGA 115X
INTEL LGA 1366 INTEL LGA 2011 INTEL LGA 2011-V3 INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
OUT IN
72
W T
240 S
0
50
99
TEM P
80. 6
W T
240 S
0
122
192
TEM P
Water Temperature Line Graph
Input Voltage : DC 5V~12V
Temperature : 0~99° C(32~210.2° F)
operate current : <20ma
DRGB LED
A
LG
L
INTE 1700
INTEL LGA 2066
1700

[ 2 ]
Installation 1
Follow the right sequence to install.
Use an appropriate amount of thermal paste.
SCM3FL20
1mm Spacer
CPU Block
SCM4M3
Spring

[ 3 ]
Installation 2
Follow the right sequence to install.
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3F6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Thumb Screw
Spring
1mm Spacer
1mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
SCM3F6 Screw

[ 4 ]
96
90
48 54
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AMD SOCKET 939 / 754 / 940
AMD SOCKET AM4
AMD SOCKET AM3 / AM3+
AMD SOCKET AM2 / AM2+
AMD SOCKET FM1 / FM2+
AM4 OUTIN
Installation 1
Follow the right sequence to install.
The thumb screw cannot be locked too tightly, the spring
is slightly pressed and the gap is kept as shown below.
The thumb screw cannot be rotated to the end. When the
spring screws too tight, the SCM3F6 screw will be driven
and will be taken away from the motherboard, which will
cause the water block and CPU not to be closed well.
Thumb Screw
Spring
1mm Spacer
1mm Spacer
Back Pad
3M Paste Pad
Metal Backplane
M3x32mm Screw
CPU Block
CPU Block PLATE(AM4)
SCM3F6 Screw

[ 5 ]
Installation 2
Follow the right sequence to install.
Thumb Screw
1mm Spacer
CPU Block
SC6-32M3 Screw
Motherboard
Original backplane
Spring

[ 6 ]
For 1200/1700 Motherboard
Accessories
4
5
1 2
2
1
3
3
Washer
Screw
Backplate
75MM
1.5MM
78MM
Adjusting Nut
Backplate Bolt
4 PCS
4 PCS
1 PC 5 PCS
4 PCS
BP-MKCPUM-1217
Assembly steps
step 1

[ 7 ]
step 3
step 2
4
5
Thumb Screw
Spring
CPU Block
1200/1700 Intel Motherboards
(Not included)

Notice
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to
excessive pressure, it will be borne by the customer. Forbidden to use the
leak teser when there is water in the loop or the pump is runing.
Bitspower requires to use of distilled or pure water or Bitspower Pellucid
Coolant as the water-cooling liquid. Also, the consumer can add Bitspower
Dye to Pellucid Coolant for the color requirement. But please do not add
any biocide by yourself. If the consumer chooses different water-cooling
liquids, the resulting impurities may cause peeling o󽗈 the coating on some
of the hardware, water channels blockage by built-up residue, improper
operation of the water pump, water tank tube breakage, and O-rings
deformation or loss sealing leading to leakage. Any issues related to the
use of inappropriate water-cooling liquid will be the responsibility of the
consumer.
[ 8 ]
記得上角要放對應的 LOGO!

[ 9 ]
記得上角要放對應的 LOGO!
80
75
72
INTEL LGA 775 INTEL LGA 115X
INTEL LGA 1366 INTEL LGA 2011 INTEL LGA 2011-V3 INTEL LGA 2066
INTEL LGA 775
INTEL LGA 115X
INTEL LGA 1366
INTEL LGA 2011
INTEL LGA 2011-V3
INTEL LGA 2066
出 進
水溫 折線圖
輸入電壓：DC 5V~12V
顯示溫度：0~99° C(32~210.2° F)
工作電流：<20ma
使用說明書
輕觸此按鍵 ，輕觸此按鍵 3 秒， 進入模式切換狀態
72
W T
240 S
0
50
99
TEM P
80. 6
W T
240 S
0
122
192
TEM P
DRGB LED
請接 1主版或 2 其他設備的 DRGB 插槽
DRGB 控制器 ( 不包括 )
BPTA-DRGBMFC
12
主版
Bitspower CPU Block Summit M Pro
with OLED (12th Gen Intel CPU) V1
A
LG
L
INTE 1700
INTEL LGA 2066
1700

[ 10 ]
核心需塗導熱膏
手轉螺絲
1 毫米墊片
冷頭
孔位固定螺絲
彈簧
請按照正確的順序安裝
安裝方式 1