Black & Decker KW750 User manual

KW750
www.blackanddecker.ae

ENGLISH
2
2
1
3
4
5
6

3
ENGLISH
AB
CD
EF
9
5
6
10
11
4
3
14
3
12
13
7
8

4
ENGLISH
P
GH
IJ
19
17
21
20
16
18
15 22

5
ENGLISH
Intended use
Your Black & Decker planer has been designed
for planing wood, wood products and plastics.
The tool is intended for hand-held use. This tool
is intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in all of the warnings
listed below refers to your mains operated
(corded) power tool or battery operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.Amoment of inattention while
operating power tools may result in serious
personal injury.
b. Use personal protective equipment.Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.

6
ENGLISH
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before
turning the power tool on.Awrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b. Do not use the power tool if the switch does
not turn it on and off.Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g. Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional power tool safety
warnings
Warning!Additional safety warnings for
planers

7
ENGLISH
•Hold the power tool by insulated gripping
surfaces only, because the cutter may
contact its own cord. Cutting a "live" wire
may make exposed metal parts of the power
tool "live" and could give the operator an
electric shock.
•Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by your
hand or against the body leaves it unstable
and may lead to loss of control.
•Wait for the cutter to stop before setting the
tool down.An exposed rotating cutter may
engage the surface leading to possible loss
of control and serious injury.
•Keep the cutter sharp. Dull or damaged
cutters may cause the planer to swerve or
stall under pressure.Always use the
appropriate type of cutter for the power tool.
•Do not touch the workpiece or the cutter
immediately after operating the tool. They
can become very hot.
•Remove all nails and metal objects from the
workpiece before planning.
•Always hold the tool with both hands and by
the handles provided.
•Immediately disconnect the cable from the
mains if it is damaged or cut.
Warning! Contact with, or inhalation of dusts
arising from planing applications may endanger
the health of the operator and possible
bystanders. Wear a dust mask specifically
designed for protection against dust and fumes
and ensure that persons within or entering the
work area are also protected.
•This tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should
be supervised to ensure that they do not play
with the appliance.
•The intended use is described in this
instruction manual. The use of any accessory
or attachment or performance of any
operation with this tool other than those
recommended in this instruction manual may
present a risk of personal injury and/or
damage to property.
Safety of others
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
•Children should be supervised to ensure that
they do not play with the appliance.
Residual risks
Additional residual risks may arise when using
the tool which may not be included in the
enclosed safety warnings. These risks can arise
from misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks can not be
avoided. These include:

8
ENGLISH
•Injuries caused by touching any
rotating/moving parts.
•Injuries caused when changing any parts,
blades or accessories.
•Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
•Impairment of hearing.
•Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech
and MDF.)
Vibration
The declared vibration emission values stated in
the technical data and the declaration of
conformity have been measured in accordance
with a standard test method provided by EN
60745 and may be used for comparing one tool
with another.The declared vibration emission
value may also be used in a preliminary
assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly using
power tools in employment, an estimation of
vibration exposure should consider, the actual
conditions of use and the way the tool is used,
including taking account of all parts of the
operating cycle such as the times when the tool
is switched off and when it is running idle in
addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury,
the user must read the instruction
manual.
Electrical safety
This tool is double insulated; therefore
no earth wire is required.Always check
that the power supply corresponds to the voltage
on the rating plate.
•If the supply cord is damaged, it must be
replaced by the manufacturer or an
authorised Black & Decker Service Centre in
order to avoid a hazard.
Features
This tool includes some or all of the following
features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Shavings discharge outlet selector
5. Planing depth adjustment knob
6. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the
tool is switched off and unplugged.
Replacing the cutting blades
(fig.A)
The cutting blades provided with this tool are
reversible. Replacement cutting blades can be
obtained from your local retailer.

9
ENGLISH
Removing
•Loosen the bolts (7) using the spanner
supplied.
•Slide the blade (8) out of the holder.
•Reverse the blade so that the unused side
comes in position. If both sides are worn, the
blade must be replaced.
Fitting
•Slide the blade into the holder until it is
against the end stop.
•Tighten the bolts using the spanner supplied.
Warning!Always replace both cutters.
Adjusting the depth of cut
(fig. B)
The depth of cut is indicated by the marking (9).
The setting range can be read from the
graduation (6).
•Turn the planing depth adjustment knob (5)
to the required depth of cut.
•Turn the knob to the ‘P' postion whenever the
tool is not in use.
Fitting and removing the
parallel fence (fig. C)
The parallel fence is used to for optimum control
on narrow workpieces.
•Thread the knob (11) into the hole on the
side of the planer and securely tighten.
•Loosen the parallel fence adjustment knob
(10).
•Slide the parallel fence into the desired
position.
•Securely tighten the parallel fence adjustment
knob.
Note : The parallel fence should be below the
planer when installed correctly.
•To remove the parallel fence proceed in
reverse order.
Connecting a vacuum cleaner to
the tool (fig. D)
An adaptor is required to connect a vacuum
cleaner or dust extractor to the tool. The adaptor
can be purchased from your local Black &
Decker retailer.
•Slide the adaptor (12) over the shavings
discharge outlet (3).
•Connect the vacuum cleaner hose (13) to the
adaptor.
Fitting the shavings collection
bag (fig. E)
The shavings collection bag is particularly useful
when working in confined spaces.
•Slide the connecting plate (14) of the bag
over either side of the shavings discharge
outlet (3).
•To prevent chips from coming out opposite
side of shavings discharge outlet, move the
shavings discharge outlet selector (4) to the
opposite side from the bag.
Emptying the shavings
collection bag
The shavings collection bag should be emptied
regularly while using it to prevent blocking.
•Unzip the bag and empty it before continuing.

10
ENGLISH
Use
Warning! Let the tool work at its own pace. Do
not overload.
•Adjust the depth of cut.
•If necessary, fit and adjust the parallel fence.
Switching on and off
Switching on
•Keep the lock-off button (2) depressed and
press the on/off switch (1).
•Release the lock-off button.
Switching off
•Release the on/off switch.
Planing
•Hold the tool with the nose piece of the shoe
resting on top of the workpiece surface.
•Switch the tool on.
•Move the tool steadily forward to perform the
cutting stroke.
•Switch the tool off after the stroke has been
completed.
Rebating (fig. F)
•Fit and adjust the parallel fence.
•Proceed as for planing.
Chamfering edges (fig. G)
The V-groove in the nose piece of the shoe
enables you to chamfer edges at 45°, 30° and
15° angles.
•Hold the tool at an angle with the desired
groove (20) around the edge of the
workpiece and perform the cutting stroke.
Parking rest (fig. H)
Your planer is equipped with a parking rest (21)
that automatically lowers into place when the tool
is lifted from the work surface. When planing, the
parking foot raises as the tool is pushed forward.
When the parking foot is lowered, the planer can
set on the work surface without the blade
touching.
Hints for optimum use
•Move the tool along the grain of the wood.
•If the grain is cross or curly, or if the
workpiece material is a hard type of wood,
adjust the depth of cut to take only a very
thin shaving at each pass and take several
passes to achieve the desired result.
•To keep the tool in a straight line, press down
the front of the tool at the start, and press
down the back of the tool at the end of the
cutting stroke.
Accessories
The performance of your tool depends on the
accessory used. Black & Decker and Piranha
accessories are engineered to high quality
standards and designed to enhance the
performance of your tool. By using these
accessories you will get the very best from your
tool.
The following types of cutting blades can be
obtained from your local retailer:
- Tungsten carbide tipped reversible cutting
blades (part no. X35007, supplied per pair)
- High-speed steel reversible cutting blades
(part no. X24192-XJ11, supplied per pair)

11
ENGLISH
Maintenance
Your tool has been designed to operate over a
long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
Warning! Before performing any maintenance,
switch off and unplug the tool.
•Regularly clean the ventilation slots in your
tool using a soft brush or dry cloth.
•Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
Replacing the drive belt (fig. I)
•Loosen the screws (15) and remove the
cover (16).
•Remove the old drive belt.
•Place the new belt (17) over the pulleys.
Place the belt over the large pulley (18) first,
then over the small pulley (19), whilst
manually rotating the belt steadily.
•Put the cover back in place and tighten the
screws.
Motor brush inspection and
replacement (fig. J)
Brushes should be regularly inspected for wear.
•Remove brush cap (22). The brushes should
slide freely in brush box. If brushes are worn
down to .3" (8mm) they should be replaced.
To reinstall, push new brush back into brush
box. If replacing existing brush, maintain same
orientation as when removed. Replace the
brush cap (do not overtighten).
Mains Plug Replacement
If a new mains plug needs to be fitted:
•Safely dispose of the old plug.
•Connect the brown lead to the live terminal of
the new plug.
•Connect the blue lead to the neutral terminal.
•If the product is class l (earthed), connect the
green / yellow lead to the earth terminal.
Warning! If your product is class ll double
insulated (only 2 wires in the cord set), no
connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs.
Any replacement fuse must be of the same
rating as the original fuse supplied with the
product.
Technical Data
KW750
(Type 4)
Input voltage Vac 220-240
Power input W 750
No-load speed min-1 16,500
Planing width mm 82
Planing depth mm 2
Rebating depth mm 12
Weight kg 2.9

12
ENGLISH
Protecting the environment
Separate collection. This product must not
be disposed of with normal household
waste.
Should you find one day that your Black &
Decker product needs replacement, or if it is of
no further use to you, do not dispose of it with
other household waste. Make this product
available for separate collection.
•Black & Decker provides a facility for
recycling Black & Decker products once they
have reached the end of their working life.
This service is provided free of charge. To
take advantage of this service please return
your product to any authorised repair agent
who will collect them on our behalf.
•You can check the location of your nearest
authorised repair agent by contacting your
local Black & Decker office at the address
indicated in this manual.Alternatively, a list of
authorized Black & Decker repair agents and
full details of our after-sales service and
contact are available on the Internet at:
www.2helpU.com.
Warranty
If a Black & Decker product becomes defective
due to a material or manufacturing defect , within
12 months from the date of purchase, Black &
Decker guarantees to replace defective parts or
replace such products to ensure minimum
inconvenience to the customer unless:
•The product has been subjected to misuse or
neglect.
•The product has sustained damage through
foreign objects, substances or accidents.
•Repairs have been attempted by persons
other than authorised repair agents or Black
& Decker service staff.
To claim on the warranty, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting
your local Black & Decker office at the address
indicated in this manual.Alternatively, a list of
authorised Black & Decker repair agents and full
details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com.
Please visit our website www.blackanddecker.ae
to register your new Black & Decker product and
to be kept up to date on new products and
special offers. Further information on the Black &
Decker brand and our range of products is
available at www.blackanddecker.ae.

13
ARABIC
2
1
3
4
5
6

AB
CD
EF
9
5
6
10
11
4
3
14
3
12
13
7
8
14
ARABIC

P
GH
IJ
19
17
21
20
16
18
15 22
15
ARABIC

16
ARABIC
ΩGóîà°S’G ¢VôZ
Ö°ûÿG §«£îàd ºª°üe ôµjO ófBG ∑ÓH §«£îàdG RÉ¡L
ºª°üe RÉ¡÷G Gòg .∂«à°SÓÑdGh á«Ñ°ûÿG äÉéàæŸGh
∂∏¡à°ùŸG ΩGóîà°S’ ºª°üe RÉ¡÷G Gòg .…hó«dG ΩGóîà°SÓd
.§≤a
áeÓ°ùdG äGOÉ°TQEG
á«FÉHô¡µdG Iõ¡LC’G áeÓ°S ¢Uƒ°üîH áeÉ©dG äGôjòëàdG
áeÓ°ùdG äGôjò– áaÉc IAGôb »¨Ñæj !ôjò–
´ÉÑJG ΩóY ÖÑ°ùàj ób .äGOÉ°TQE’G áaÉch
áeó°U çhóM ‘ »∏j ɪ«a IOQGƒdG äGOÉ°TQE’Gh äGôjòëàdG
.IÒ£N áHÉ°UEG hCG/h ≥jôM hCG/h á«FÉHô¡c
´ƒLô∏d äGOÉ°TQE’Gh äGôjòëàdG áaɵH ®ÉØàM’G ≈Lôj
.kÓÑ≤à°ùe É¡«dEG
äGôjòëàdG áaÉc ‘ OQGƒdG "»FÉHô¡c RÉ¡L"í∏£°üŸG
πª©j …òdG »FÉHô¡µdG RÉ¡÷G ¤EG Ò°ûj √ÉfOCG IQƒcòŸG
…òdG »FÉHô¡µdG RÉ¡÷G hCG (Ék«µ∏°S) »FÉHô¡µdG QÉ«àdÉH
.(Ék«µ∏°S’) ájQÉ£ÑdÉH πª©j
πª©dG á≤£æe áeÓ°S .1
áØ«¶f ádÉM ‘ πª©dG á≤£æe ≈∏Y ®ÉØ◊G »¨Ñæj .CG
á¶àµŸGh áª∏¶ŸG ≥WÉæŸG ÖÑ°ùàJ .Gkó«L IAÉ°†eh
.çOGƒM ´ƒbh ‘ ΩÉcôdÉH
AGƒLCG ‘ á«FÉHô¡µdG Iõ¡LC’G 𫨰ûàH º≤J ’ .Ü
á∏HÉb πFGƒ°S OƒLh ‘ É¡∏«¨°ûJ πãe ;ájQÉéØfG
èàæj á«FÉHô¡µdG Iõ¡LC’G .QÉÑZ hCG äGRÉZ hCG ∫É©à°TÓd
.áæNOC’G hCG QÉѨdG ∫É©°TEG ¤EG …ODƒJ ób äGQGöT É¡æY
RÉ¡÷G 𫨰ûJ AÉæKCG ÚLôØàŸGh ∫ÉØWC’G OÉ©HEG »¨Ñæj .ê
≈∏Y Iô£«°ù∏d ∂fGó≤a ‘ AÉ¡dE’G ÖÑ°ùàj ób .»FÉHô¡µdG
.RÉ¡÷G
á«FÉHô¡µdG áeÓ°ùdG .2
QÉ«àdG Qó°üe ™e »FÉHô¡µdG QÉ«àdG ¢ùHGƒb ≥aGƒJ Ωõ∏j .CG
,á≤jôW ájCÉH ¢ùHÉ≤dG πjó©J Ék≤∏£e ÖæŒ .»FÉHô¡µdG
.á°VQCÉŸG Iõ¡LC’G ™e ÅjÉ¡e ¢ùHGƒb ájCG Ωóîà°ùJ ’h
QÉ«àdG QOÉ°üeh ádó©ŸG ÒZ ¢ùHGƒ≤dG …ODƒJ ±ƒ°S
áeó°üd ¢Vô©àdG ô£N π«∏≤J ¤EG á≤aGƒàŸG »FÉHô¡µdG
.á«FÉHô¡c
Ö«HÉfC’G πãe á°VQDƒŸG í£°SCÓd º°ù÷G á°ùeÓe ÖæŒ .Ü
ô£N OGOõj .äÉLÓãdGh óbGƒŸGh ICÉaóŸG Iõ¡LCGh
.É k °VQDƒe ∂ª°ùL ¿Éc GPEG á«FÉHô¡c áeó°üH ∂àHÉ°UEG
.áÑWôdG AGƒLC’G hCG ô£ª∏d á«FÉHô¡µdG Iõ¡LC’G ¢Vô©J ’ .ê
¤EG »FÉHô¡µdG RÉ¡÷G πNGO AÉŸG π∏îJ …ODƒj ±ƒ°S
.á«FÉHô¡c áeó°üH áHÉ°UE’G ô£N IOÉjR
’ .»FÉHô¡µdG QÉ«àdG ∂∏°S ∫ɪ©à°SG IAÉ°SEG ΩóY »¨Ñæj .O
RÉ¡÷G πª◊ »FÉHô¡µdG QÉ«àdG ∂∏°S Ék≤∏£e Ωóîà°ùJ
»¨Ñæj .QÉ«àdG øY ¬∏°üa hCG ¬Ñë°S hCG »FÉHô¡µdG
hCG IQGô◊G øY Gkó«©H »FÉHô¡µdG QÉ«àdG ∂∏°ùH ®ÉØàM’G
ójõJ .ácôëàŸG AGõLC’G hCG IOÉ◊G ±Gƒ◊G hCG âjõdG
áeó°üH áHÉ°UE’G ô£N øe áµHÉ°ûàŸG hCG áØdÉàdG ∑Ó°SC’G
.á«FÉHô¡c
Ωóîà°SG ,≥∏£dG AGƒ¡dG ‘ »FÉHô¡µdG RÉ¡÷G 𫨰ûJ óæY .`g
.≥∏£dG AGƒ¡dG ‘ ΩGóîà°SÓd Ö°SÉæe π«°UƒJ ∂∏°S
‘ ΩGóîà°SÓd Ö°SÉæe »FÉHô¡c QÉ«J ∂∏°S ΩGóîà°SG
.á«FÉHô¡c áeó°üd ¢Vô©àdG ô£N øe π∏≤j ≥∏£dG AGƒ¡dG
‘ »FÉHô¡µdG RÉ¡÷G 𫨰ûJ ÖæŒ øµÁ ’ ¿Éc GPEG.h
øe ájÉbh RÉ¡L ΩGóîà°SG »¨Ñæj ¬fEÉa ,ÖWQ ¿Éµe
QÉ«àdG øe ájÉbƒdG RÉ¡L ΩGóîà°SG π∏≤j .»≤ÑàŸG QÉ«àdG
.á«FÉHô¡c áeó°üH áHÉ°UE’G ô£N øe »≤ÑàŸG
á«°üî°ûdG áeÓ°ùdG .3
º«∏°ùdG ¢ù◊G Ωóîà°SGh ¬∏©ØH Ωƒ≤J Ée ÖbGQh Ék¶≤j øc .CG
Ωóîà°ùJ ’ .»FÉHô¡µdG RÉ¡÷G 𫨰ûàH Ωƒ≤J ÉeóæY
ÒKCÉJ â– hCG Ékµ¡æe ¿ƒµJ ÉeóæY »FÉHô¡µdG RÉ¡÷G
ÖÑ°ùàJ ób .AGhódG hCG á«dƒëµdG äÉHhöûŸG hCG ÒbÉ≤©dG
‘ á«FÉHô¡µdG Iõ¡LC’G 𫨰ûJ AÉæKCG á∏بdG øe á¶◊
.á¨dÉH á«°üî°T áHÉ°UEG çhóM
»bGh ÉkehO …óJQG .á«°üî°ûdG ájÉbƒdG äGó©e Ωóîà°SG .Ü
πãe ájÉbƒdG äGó©e ΩGóîà°SG π∏≤j ±ƒ°S .Ú©dG
á©Ñ≤dGh ≥∏Mõà∏d á©fÉŸG ájòMC’Gh áHôJC’G äÉeɪc
äÉHÉ°UEG çhóM ô£N øe ™ª°ùdG »bGhh áÑ∏°üdG
.á«°üî°T

17
ARABIC
¿CG øe ócCÉJ .Oƒ°ü≤ŸG ÒZ 𫨰ûàdG AóH ™æe Ú©àj .ê
QÉ«àdG Qó°üà π«°UƒàdG πÑb ≥∏¨dG ™°Vh ‘ ìÉàØŸG
πªM hCG ™aQ hCG ájQÉ£ÑdG áeõëH hCG/h »FÉHô¡µdG
™HÉ°UC’Gh á«FÉHô¡µdG Iõ¡LC’G πªM …ODƒj .RÉ¡÷G
á«FÉHô¡µdG Iõ¡LC’G πªM hCG ,ìÉàØŸG ≈∏Y áYƒ°Vƒe
´ƒbh ¤EG ,𫨰ûàdG ™°Vh ‘ ¿ƒµJ »àdG ᣰûædG
.çOGƒM
πÑb …õ«∏‚EG ìÉàØe hCG …OÉY ìÉàØe …CG ádGREÉH ºb .O
ìÉàØŸG ∑ôJ ÖÑ°ùàj ób .»FÉHô¡µdG RÉ¡÷G 𫨰ûJ
çhóM ‘ »FÉHô¡µdG RÉ¡÷G øe QGhO AõéH Ék`≤∏©àe
.á«°üî°T áHÉ°UEG
äÉÑK ≈∏Y ®ÉØ◊G »¨Ñæj .•ôØŸG ÜGÎb’G ΩóY »¨Ñæj .`g
øe ∂æµÁ Gòg .äÉbhC’G áaÉc ‘ ¿RGƒàdGh Úeó≤dG
∞bGƒŸG ‘ »FÉHô¡µdG RÉ¡÷G ≈∏Y Ió«÷G Iô£«°ùdG
.á©bƒàŸG ÒZ
¢ùHÓŸG …óJôJ ’ .áÑ°SÉæŸG ¢ùHÓŸG AGóJQG »¨Ñæj .h
∑ô©°T ≈∏Y ®ÉØ◊G »¨Ñæj .äGôgƒéŸG hCG á°VÉØ°†ØdG
ób .ácôëàŸG AGõLC’G øY Gkó«©H ∂JGRÉØbh ∂°ùHÓeh
ô©°ûdG hCG äGôgƒéŸG hCG á°VÉØ°†ØdG ¢ùHÓŸG ≥∏©àJ
.ácôëàŸG AGõLC’ÉH πjƒ£dG
êGôîà°SG ¢Uƒ°üîH Iôaƒe Iõ¡LCG ∑Éæg âfÉc GPEG.R
Iõ¡LC’G ∂∏J π«°UƒJ øe ócCÉJ ,™ª÷G ≥aGôeh QÉѨdG
ΩGóîà°SG π∏≤j ¿CG øµÁ .Ö°SÉæŸG πµ°ûdÉH É¡eGóîà°SGh
.QÉѨdÉH á£ÑJôŸG ôWÉîŸG çhóM øe Iõ¡LC’G ∂∏J
¬H ájÉæ©dGh »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG .4
¢VôZ ‘ »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ÖæŒ Ú©àj .CG
Ö°SÉæàj …òdG »FÉHô¡µdG RÉ¡÷G Ωóîà°SG .Ö°SÉæe ÒZ
Ωƒ≤j ±ƒ°S .√ójôJ …òdG ΩGóîà°S’Gh ¢Vô¨dG ™e
π°†aCG πµ°ûH πª©dG AGOCÉH í«ë°üdG »FÉHô¡µdG RÉ¡÷G
.¬∏LCG øe ¬ª«ª°üJ ” …òdG ∫ó©ŸÉH ÉkfÉeCG ÌcCGh
ìÉàØŸG º≤j ⁄ kGPEG »FÉHô¡µdG RÉ¡÷G Ωóîà°ùJ ’ .Ü
øµÁ ’ »FÉHô¡c RÉ¡L …CG .¬∏«¨°ûJ ±É≤jEGh ¬∏«¨°ûàH
»¨Ñæjh Gkô£N ¿ƒµj ìÉàØŸG ΩGóîà°SÉH ¬«a ºµëàdG
.¬MÓ°UEG
QÉ«àdG Qó°üe øY »FÉHô¡µdG RÉ¡÷G ¢ùHÉb π°üaG .ê
ájCG AGôLEG πÑb ájQÉ£ÑdG áeõM øY hCG/h »FÉHô¡µdG
Iõ¡LC’G ‘ äÉ≤ë∏e ájCG Ö«côJ hCG äGÒ«¨J hCG äÓjó©J
á«FÉbƒdG áeÓ°ùdG äGAGôLEG π∏≤J .É¡æjõîJ hCG á«FÉHô¡µdG
¿hO ICÉéa »FÉHô¡µdG RÉ¡÷G 𫨰ûJ AóH ô£N øe √òg
.ó°üb
Gkó«©H áeóîà°ùŸG ÒZ á«FÉHô¡µdG Iõ¡LC’G øjõîàH ºb .O
ÒZ ¢UÉî°TCÓd íª°ùJ ’h ∫ÉØWC’G ∫hÉæàe øY
ÒZ hCG »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG ≈∏Y øjOÉà©ŸG
RÉ¡÷G 𫨰ûàH äGOÉ°TQE’G √òg ≈∏Y Ú©∏£ŸG
ÉeóæY Gkô£N πµ°ûJ á«FÉHô¡µdG Iõ¡LC’G .»FÉHô¡µdG
.ÚHQóe ÒZ Úeóîà°ùe ój ‘ ¿ƒµJ
RÉ¡÷G ¢üëaG .á«FÉHô¡µdG Iõ¡LC’G áfÉ«°U »¨Ñæj .`g
ácôM ¥ƒ©J »àdG hCG áÑ«©ŸG AGõLC’G ≈∏Y ±ô©à∏d
AGõLC’G øe √ƒ∏N øe ócCÉà∏dh ácôëàŸG AGõLC’G
IAÉØc ≈∏Y ôKDƒJ ób iôNCG ádÉM …CG øeh IQƒ°ùµŸG
,∞∏J …CG ≈∏Y Qƒã©dG ” GPEG .á«FÉHô¡µdG Iõ¡LC’G 𫨰ûJ
èàæJ .ΩGóîà°S’G πÑb »FÉHô¡µdG RÉ¡÷G ìÓ°UEG »¨Ñæj
Iõ¡LC’G áfÉ«°U Aƒ°S øY çOGƒ◊G øe ójó©dG
.á«FÉHô¡µdG
IOÉM ádÉM ‘ ™£≤dG äGhOCG ≈∏Y ®ÉØ◊G »¨Ñæj .h
Ö°SÉæe πµ°ûH É¡«∏Y ßaÉëŸG ™£≤dG äGhOCG .áØ«¶fh
∫É£YCÓd á°VôY πbCG »g IOÉM á©WÉb äGôØ°ûH IOhõŸGh
.ºµëàdG ‘ π¡°SCGh
¬FGõLCGh ¬JÉ≤ë∏eh »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG »¨Ñæj .R
±hôX òNCG ™e ,äGOÉ°TQE’G √ò¡d Ék≤ah ∂dP ¤EG Éeh
ÖÑ°ùàj ób .QÉÑàY’G ‘ √ò«ØæJ OGôŸG πª©dGh πª©dG
𫨰ûJ äÉ«∏ªY πLCG øe »FÉHô¡µdG RÉ¡÷G ΩGóîà°SG
çhóM ‘ IOƒ°ü≤ŸG 𫨰ûàdG äÉ«∏ªY øY áØ∏àfl
.ôWÉfl
áfÉ«°üdG .5
ᣰSGƒH »FÉHô¡µdG RÉ¡÷G ìÓ°UEGh áfÉ«°U »¨Ñæj .CG
Gòg .§≤a á≤HÉ£e QÉ«Z ™£b ΩGóîà°SÉH πgDƒe ¢üî°T
.»FÉHô¡µdG RÉ¡÷G áeÓ°S ≈∏Y ®ÉØ◊G øª°†«°S
RÉ¡÷G ¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò–
»FÉHô¡µdG
¢Uƒ°üîH á«aÉ°VEG áeÓ°S äGôjò– !ôjò–
.§«£îàdG Iõ¡LCG

18
ARABIC
í£°SCG hP ¢†Ñ≤e ᣰSGƒH »FÉHô¡µdG RÉ¡÷G ∂°ùeG •
…ODƒj óbh .É¡µ∏°S ™£≤dG IóMh ¢ùeÓJ ó≤a ,ádhõ©e
∂∏°ùd á«fó©ŸG AGõLC’G ájô©J ¤EG "»M"QÉ«J ∂∏°S ™£b
¢Vô©J ‘ ∂dP ÖÑ°ùàj ób ºK øeh ;"»◊G"QÉ«àdG
.á«FÉHô¡c áeó°üd π¨°ûŸG
ΩɵME’ iôNCG á«∏ªY á≤jôW …CG hCG ∂HÉ°ûŸG Ωóîà°SG
•
¿EG .Iô≤à°ùe á°üæe ≈∏Y πª©dG á©£b º«YóJh â«ÑãJ
∂ª°ùL ≈∏Y É¡©°Vh hCG ó«dG ᣰSGƒH πª©dG á©£b ∂°ùe
¿Gó≤a ¤EG …ODƒj óbh Iô≤à°ùe ÒZ πª©dG á©£b π©éj
.Iô£«°ùdG
≈∏Y RÉ¡÷G ™°Vh πÑb ™£≤dG IóMh ∞bƒJ ≈àM ô¶àfG
•
πNóJ ób áaƒ°ûµŸG IQGhódG ™£≤dG IóMh .πª©dG í£°S
çhóMh Iô£«°ù∏d øµ‡ ó≤a ¤EG …ODƒJh í£°ùdG ‘
.IÒ£N áHÉ°UEG
ÖÑ°ùàJ ób .IOÉM ™£≤dG IóMh ≈∏Y ®ÉØ◊G »¨Ñæj •
RÉ¡L ±GôëfG ‘ áØdÉàdG hCG IOÉ◊G ÒZ ™£≤dG äGóMh
IóMh ÉkehO Ωóîà°SG .§¨°V â– ¬ØbƒJ hCG §«£îàdG
.»FÉHô¡µdG RÉ¡é∏d áÑ°SÉæŸG ™£≤dG
ó©H IöTÉÑe ™£≤dG IóMh hCG πª©dG á©£b ¢ùª∏J ’ •
.GkóL áæNÉ°S ¿ƒµJ ¿CG øµÁ .RÉ¡÷G 𫨰ûJ
á©£b øe á«fó©ŸG AÉ«°TC’Gh ÒeÉ°ùŸG áaÉc ádGREÉH ºb
•
.§«£îàdG πÑb πª©dG
ΩGóîà°SÉHh øjó«dG Éà∏c ΩGóîà°SÉH ÉkªFGO RÉ¡÷G ∂°ùeG
•
.¬©e IôaƒŸG ¢†HÉ≤ŸG
hCG ÉkØdÉJ ¿Éc GPEG QƒØdG ≈∏Y ¢ùHÉ≤dG øe πHɵdG π°üaG
•
.´ƒ£≤e
§«£îJ øY Å°TÉædG QÉѨdG ¥É°ûæà°SG hCG ™e ¢ùeÓàdG !ôjò–
ÚLôØàŸGh π¨°ûŸG áë°U ¢Vô©oj ób äÉ≤«Ñ£àdG
᪪°üe á°UÉN áHôJCG áeɪc …óJQG .ô£î∏d Ú∏ªàëŸG
ájɪM øe É k °†jCG ócCÉJh áæNOC’Gh áHôJC’G øe ájɪë∏d
.πª©dG á≤£æe ¤EG Ú∏NGódG hCG πNGO øjOƒLƒŸG ¢UÉî°TC’G
hhP ¢UÉî°TC’G ¬eóîà°ù«d ºª°üe ÒZ RÉ¡÷G Gòg •
á«fóàŸG á«∏≤©dGh á«°ù◊Gh á«ægòdGh ájó°ù÷G äGQó≤dG
’EG (∫ÉØWC’G ∂dP ‘ ÉÃ) Úà∏«∏≤dG áaô©ŸGh IÈÿGh
á≤∏©àŸG äɪ«∏©àdG º¡FÉ£YEG hCG º¡«∏Y ±GöTE’G πX ‘
øY ∫hDƒ°ùŸG ¢üî°ûdG πÑb øe RÉ¡÷G ΩGóîà°SÉH
ΩóY ¿Éª°†d ∫ÉØWC’G ≈∏Y ±GöTE’G Ωõ∏j .º¡àeÓ°S
.RÉ¡÷ÉH º¡ãÑY
.Gòg äGOÉ°TQE’G π«dO ‘ í°Vƒe Oƒ°ü≤ŸG ΩGóîà°S’G
•
á«∏ªY ájCG ò«ØæJ hCG á≤ë∏e IóMh …CG ΩGóîà°SG ÖÑ°ùàj ób
π«dO ‘ É¡H ≈°UƒŸG ∂∏J ±ÓîH RÉ¡÷G Gò¡H
∞∏J hCG/h á«°üî°T áHÉ°UEG çhóM ‘ Gòg äGOÉ°TQE’G
.äɵ∏પ∏d
øjôNB’G áeÓ°S
hhP ¢UÉî°TC’G ¬eóîà°ù«d ºª°üe ÒZ RÉ¡÷G Gòg •
á«fóàŸG á«∏≤©dGh á«°ù◊Gh á«ægòdGh ájó°ù÷G äGQó≤dG
’EG (∫ÉØWC’G ∂dP ‘ ÉÃ) Úà∏«∏≤dG áaô©ŸGh IÈÿGh
á≤∏©àŸG äɪ«∏©àdG º¡FÉ£YEG hCG º¡«∏Y ±GöTE’G πX ‘
øY ∫hDƒ°ùŸG ¢üî°ûdG πÑpb øe RÉ¡÷G ΩGóîà°SÉH
.º¡àeÓ°S
º¡ãÑY ΩóY ¿Éª°†d ∫ÉØWC’G ≈∏Y ±GöTE’G Ωõ∏j
•
.RÉ¡÷ÉH
á«≤ÑàŸG ôWÉîŸG
»àdGh RÉ¡÷G ΩGóîà°SG óæY á«aÉ°VEG á«≤Ñàe ôWÉfl CÉ°ûæJ ób
CÉ°ûæJ óbh .á≤aôŸG áeÓ°ùdG äGôjò– ‘ á檰†e ¿ƒµJ ’ ób
Éeh ∫ƒ£ŸG ΩGóîà°S’G hCG ΩGóîà°S’G Aƒ°S øY ôWÉîŸG ∂∏J
.∂dP ¤EG
äGhOCG ΩGóîà°SGh á∏°üdG äGP áeÓ°ùdG íFGƒd ≥«Ñ£J ™e ≈àM
√òg πª°ûJ .á«≤ÑàŸG ôWÉîŸG ¢†©H ÖæŒ øµÁ ’ ,áeÓ°ùdG
:»∏j Ée á«≤ÑàŸG ôWÉîŸG

19
ARABIC
AGõLCG ájCG á°ùeÓe øY áŒÉædG äÉHÉ°UE’G •
.ácôëàe/IQGhO
äGôØ°T hCG AGõLCG ájCG Ò«¨J óæY çó– »àdG äÉHÉ°UE’G
•
.äÉ≤ë∏e hCG
óæY .RÉ¡é∏d ∫ƒ£ŸG ΩGóîà°S’G øY áŒÉædG äÉHÉ°UE’G
•
∞bƒàdG øe ócCÉJ ,á∏jƒW äGÎØd RÉ¡L …CG ΩGóîà°SG
.᪶àæe á∏°UÉa äGÎØd
™ª°ùdG ∞©°V
•
Å°TÉædG QÉѨdG ¥É°ûæà°SG øY áŒÉædG á«ë°üdG ôWÉîŸG •
™e ΩGóîà°S’G :∫ÉãŸG π«Ñ°S ≈∏Y) RÉ¡÷G ΩGóîà°SG óæY
Ö°ûNh •ƒ∏ÑdG Ö°ûN ¢Uƒ°üÿG ¬Lh ≈∏Yh ÜÉ°ûNC’G
.(áaÉãµdG §°Sƒàe »Ø«∏dG Ö°ûÿGh ¿GõdG
RGõàg’G
äÉfÉ«ÑdG ‘ IQƒcòŸG áæ∏©ŸG äGRGõàg’G çÉ©ÑfG º«b
QÉÑàNG á≤jô£d Ék≤ah É¡°SÉ«b ” ≥aGƒàdG äÉeƒ∏©eh á«æØdG
EN 60745 QÉ«©ŸG ÖLƒÃ É¡«∏Y ¢Uƒ°üæe á«°SÉ«b
øµÁh .ôNBG ™e Ée RÉ¡L áfQÉ≤Ÿ É¡eGóîà°SG øµÁh
º««≤J AGôLEG ‘ áæ∏©ŸG äGRGõàg’G çÉ©ÑfG ᪫b ΩGóîà°SG
.¢Vô©à∏d ‹hCG
AÉæKCG äGRGõàg’G çÉ©ÑfG ᪫b ∞∏àîJ ¿CG øµÁ !ôjò–
áæ∏©ŸG ᪫≤dG øY »FÉHô¡µdG RÉ¡é∏d »∏©ØdG ΩGóîà°S’G
OGOõj ób .RÉ¡÷G ΩGóîà°SG ¥ôW ≈∏Y ∂dP ∞bƒàj å«M
.QƒcòŸG iƒà°ùŸG øY RGõàg’G iƒà°ùe
áeÓ°ùdG äGAGôLEG ójóëàd RGõàgÓd ¢Vô©àdG º««≤J óæY
ájɪ◊ EC/2002/44 QÉ«©ŸG ÖLƒÃ áHƒ∏£ŸG
πµ°ûH á«FÉHô¡µdG Iõ¡LC’G ¿ƒeóîà°ùj øjòdG ¢UÉî°TC’G
º««≤J á«∏ªY ‘ »∏j Ée IÉYGôe Ωõ∏j ,º¡∏ªY ‘ º¶àæe
á≤jô£dGh ΩGóîà°SÓd á«∏©ØdG ±hô¶dG :RGõàgÓd ¢Vô©àdG
AGõLCG áaÉc òNCG ∂dP ‘ Éà ,É¡H RÉ¡÷G ΩGóîà°SG ºàj »àdG
É¡«a ºàj »àdG äÉbhC’G πãe ;QÉÑàY’G ‘ 𫨰ûàdG IQhO
,¬eGóîà°SG øY ∞bƒàdG óæY hCG RÉ¡÷G 𫨰ûJ ±É≤jEG
.𫨰ûàdG äÉbhCG ¤EG áaÉ°VE’ÉH
Iõ¡LC’G ≈∏Y äÉ≤°ü∏ŸG
:RÉ¡÷G ≈∏Y áë°Vƒe á«dÉàdG äÉeƒ°SôdG
≈∏Y »¨Ñæj ,áHÉ°UE’G ô£N π«∏≤àd !ôjò–
.äGOÉ°TQE’G π«dO IAGôb Ωóîà°ùŸG
á«FÉHô¡µdG áeÓ°ùdG
áLÉM ’ ,∂dòd ;É k LhOõe k’õY ∫hõ©e RÉ¡÷G Gòg
≥aGƒJ øe ÉkªFGO ócCÉàdG »¨Ñæjh .»°VQCG ∂∏°S ¤EG
áMƒd ≈∏Y í°VƒŸG ó¡÷G ™e »FÉHô¡µdG QÉ«àdG Qó°üe
.򾲈dG
øe ¬dGóÑà°SG Öéj ,»FÉHô¡µdG QÉ«àdG ∂∏°S ∞∏J ádÉM ‘
•
ôµjO ófBG ∑ÓH áfÉ«°U õcôe hCG á©æ°üŸG ácöûdG πÑpb
.ôWÉîŸG Öæéàd óªà©e
ÉjGõŸG
:á«dÉàdG ÉjGõŸG áaÉc hCG øe ¢†©H ≈∏Y RÉ¡÷G Gòg πªà°ûj
±É≤jEG/𫨰ûJ ìÉàØe .1
≥∏Z QR .2
IQÉéædG êGôNEG òØæe 3
IQÉéædG êGôNEG òØæe QÉ«àNG IóMh .4
§«£îàdG ≥ªY §Ñ°V ¢Uôb .5
§«£îàdG ≥ªY êQóJ .6
Ö«cÎdG
¬∏°üah RÉ¡÷G 𫨰ûJ ±É≤jEG øe ócCÉJ ,Ö«cÎdG πÑb !ôjò–
.»FÉHô¡µdG QÉ«àdG Qó°üe øY
("CG"πµ°ûdG) ™£≤dG äGôØ°T ∫GóÑà°SG
øµÁ .¢ùµ©∏d á∏HÉb RÉ¡÷G Gòg ™e IôaƒŸG ™£≤dG äGôØ°T
.»∏ëŸG ´RƒŸG øe á∏jóÑdG ™£≤dG äGôØ°T ≈∏Y ∫ƒ°ü◊G

20
ARABIC
ádGRE’G
™e ôaƒŸG ìÉàØŸG ΩGóîà°SÉH (7) øjQɪ°ùŸG ∂a •
.RÉ¡÷G
.πeÉ◊G êQÉN (8) IôØ°ûdG Öë°SG
•
‘ Ωóîà°ùŸG ÒZ ÖfÉ÷G ô≤à°ùj å«ëH IôØ°ûdG ¢ùµYG •
∑Ó¡à°SG ádÉM ‘h .Ö°SÉæŸG ΩGóîà°S’G ™°Vƒe
.IôØ°ûdG Ò«¨J Ωõ∏j ,ÚÑfÉ÷G
Ö«cÎdG
óæY ∞bƒàJ ≈àM πeÉ◊G πNGO ¤EG IôØ°ûdG Öë°SG •
.ájÉ¡ædG
.RÉ¡÷G ™e ôaƒŸG ìÉàØŸG ΩGóîà°SÉH øjQɪ°ùŸG §HQG
•
.ÉkªFGO ™£≤dG »JóMh Éà∏c ∫óÑà°SG !ôjò–
("Ü"πµ°ûdG) ™£≤dG ≥ªY §Ñ°V
IAGôb øµÁ .(9) èjQóàdG ∫ÓN øe í°Vƒe ™£≤dG ≥ªY
.(6) êQóàdG øe §Ñ°†dG §°Sƒàe
≥ªY ¤EG (5) §«£îàdG ≥ªY §Ñ°V ¢Uôb IQGOEÉH ºb •
.܃∏£ŸG ™£≤dG
¿ƒµj ÉeóæY "P" ™°VƒŸG ¤EG ¢Uô≤dG IQGOEÉH ºb
•
.Ωóîà°ùe ÒZ RÉ¡÷G
("ê"πµ°ûdG) …RGƒŸG êÉ«°ùdG ádGREGh Ö«côJ
ºµ– π°†aCG ≈∏Y ∫ƒ°üë∏d …RGƒŸG êÉ«°ùdG ΩGóîà°SG ºàj
.á≤«°†dG πª©dG ™£pb ‘
RÉ¡L ÖfÉL ‘ áëàØdG ‘ (11) ¢Uô≤dG πNOCG•
.ΩɵMEÉH ¬£HQGh §«£îàdG
.(10) …RGƒŸG êÉ«°ùdG §Ñ°V ¢Uôb ∂a
•
.¬«a ܃ZôŸG ™°VƒŸG ¤EG …RGƒŸG êÉ«°ùdG Öë°SG •
.ΩɵMEÉH …RGƒŸG êÉ«°ùdG §Ñ°V ¢Uôb §HQG •
RÉ¡L πØ°SCG …RGƒŸG êÉ«°ùdG ¿ƒµj ¿CG »¨Ñæj :á¶MÓe
.í«ë°U πµ°ûH ¬Ñ«côJ óæY §«£îàdG
Ö«JôJ ‘ á≤HÉ°ùdG äGƒ£ÿG ™ÑJG …RGƒŸG êÉ«°ùdG ádGRE’
•
.»°ùµY
(O πµ°ûdG) RÉ¡÷ÉH á«FÉHô¡c á°ùæµe π«°UƒJ
IóMh hCG á«FÉHô¡c á°ùæµe π«°Uƒàd ÅjÉ¡e ΩGóîà°SG ܃∏£e
´Rƒe øe ÅjÉ¡ŸG AGöT øµÁ .RÉ¡÷ÉH áHôJCG êGôîà°SG
.»∏ëŸG ôµjO ófBG ∑ÓH
.(3) IQÉéædG êGôNEG òØæe ¥ƒa (12) ÅjÉ¡ŸG ™aOG
•
(13) á«FÉHô¡µdG á°ù浟G ΩƒWôN π«°UƒàH ºb •
.ÅjÉ¡ŸÉH
("`g"πµ°ûdG) IQÉéædG ™«ªŒ áÑ«≤M Ö«côJ
πª©dG óæY ¢UÉN ƒëf ≈∏Y Ió«Øe IQÉéædG ™«ªŒ áÑ«≤M
.á≤∏¨ŸG øcÉeC’G ‘
ÖfÉL …CG ¥ƒa áÑ«≤◊ÉH (14) π«°UƒàdG áë«Ø°U ™aOG
•
.(3) IQÉéædG êGôNEG òØæe ÖfGƒL øe
πHÉ≤ŸG ÖfÉ÷G øe êhôÿG øe Qƒ°û≤dGh äÉbÉbôdG ™æŸ
•
òØæe QÉ«àNG IóMh ∑ôM ,IQÉéædG êGôNEG òØæe ‘
.áÑ«≤◊G øe πHÉ≤ŸG ÖfÉ÷G á«MÉf (4) IQÉéædG êGôNEG
IQÉéædG ™«ªŒ áÑ«≤M ≠jôØJ
AÉæKCG ΩɶàfÉH IQÉéædG ™«ªŒ áÑ«≤M ≠jôØJ »¨Ñæj
.OGó°ùf’G ™æŸ ΩGóîà°S’G
.QGôªà°S’G πÑb É¡JÉjƒàfi ÆôaCGh áÑ«≤◊G íàaG
•