Black Horse Model HEINKEL HE 111 User manual

Instruction Manual book

MadeinVietnam.

SPECIFICATION

1Wingspan : 1,750mm 68.90 in.

1Length : 1,280 mm 50.39 in.

1Weight : 3.2 - 3.5 kg 7.04 -7.7 lbs.

Parts listing required (not included):

1Radio : 06 channels.

1Servo : 07-09 size (29x13x30)mm.

1Engine : 25 -2 stroke (02PCS).

1Electric Motor : OMA - 3820 - 1200(2pcs)

1Battery: 3 - 4CELLS-LIPO - 11.1V-14.8V - 3,250 mAh (2 Packs).

1Speed control : 60 A (02pcs).

1Propeller: 10 x 5.

ITEM CODE: BH143.

HEINKEL HE 111- Item code:BH143. Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your HEINKEL HE 111. Use the parts listing below

to identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

1Thick cyanoacrylate glue.

130 minute epoxy.

15 minute epoxy.

1Hand or electric drill.

1Assorted drill bits.

1Modellingknife.

1Straightedge ruler.

12mm ball driver.

1Phillips head screwdriver.

1220 grit sandpaper.

190° square or builder’s triangle.

1Wire cutters.

1Masking tape & T-pins.

1Thread-lock.

1Paper towels.

Some more parts.

HARDWARE PACK

COWLING.

Landinggear.....

Toavoidscratching yournew airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftandto protectthetable. Keepacoupleof

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrial fitalltheparts.Makesureyouhave

the correct parts and that they fit and are

alignedproperlybefore gluing!Thiswill assure

proper assembly.

HEINKELHE111 ARFishand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

ofmanyharshchemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderand acetone.Donotletthesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

1(1) Fuselage.

WING ASSEMBLY

1(1) Right wing half with pre-installed

aileron.

1(1) Left wing half with pre-installed

aileron.

Tail section assembly

1(1) Vertical stabilizer with pre-

installedrudder.

1(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

HEINKEL HE 111- Item code:BH143. Instruction Manual

Caution: this model is not a toy!

Ifyouarea beginner to this typeofpoweredmodel, please ask anexperiencedmodelflyerfor help

and support. If you attempt to operate the model without knowing what you are doing you could

easily injure yourself or somebody else. Please keep your safety and well-being in mind at all

times.

Important: before you start construction

Even if you have already built a large number of RC models please read right through these

instructionsandcheckallthe kit components against thepartslist.We have taken great trouble to

keep construction as simple as possible, without making any compromises in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the film covering due to major fluctuations in weather

conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a

component. These minor faults are in the nature of film-covered built-up wooden structures, and

can easily be corrected using a heat gun, as commonly used for modelling.

Creases: Blow warm air over the area and rub down with a soft cloth.

Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply

warm air to remove the creases from the covering.

Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the

film may melt and holes may be formed.

This model is highly pre-fabricated and can be built in a very short time. However, the work which

you have to carry out is important and must be done carefully.Themodelwill only bestrongand fly

well if you complete your tasks competently - so please work slowly and accurately.

When self-tapping screws have to be screwed into wood, apply a little white glue to prevent

them shaking loose: just squirt white glue into the hole and fit the screw.

+ This is not a toy

+ Be sure that no other flyers are using your

radiofrequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+Theglowplugclipmustbesecurelyattached

to the glow plug.

SAFETY PRECAUTION. + Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

the propeller.

+ Do not start the engine if people are near.

Donotstandin line with thesideofthe propel-

ler.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ningpropeller

REPLACEMENT LARGE PARTS

B. Wing panel(B1,B2).

A. Cowling (A1,A2,A3,A4).

C. Fuselage.

B2. B1.

A. A.

D. Fuselage top hatch.

E. Horizontal stabilizer.(E1,E2)

E2. E1.

G1.

G2.

H1.

H2.

F. Rudder.

G1.Aluminium tube wing.

H.Canopy .

K.Pilot

A1. A2.

A3.

A4.

G2. Aluminiumtube

horizontal stabilizer

HEINKEL HE 111- Item code:BH143. Instruction Manual

REPLACEMENT SMALL PARTS

Cutthe covering

awayfromtheslot.

Bottom side.

Flap Aileron

2. Wheels

1. Retract main gear (1a,1b)

3. Fuel tanks.

4.Tailgear.

7.Spinners.

5.Engine mount ply of wood .

6. Plastic - engine mount.

8.Plastic parts for Fuel tank.

11) Install the rubber grommets and brass

eyelets onto the aileron servos.

1.INSTALLING THE AILERON SERVOS.

Top side.

I.AILERON.

9.Plastic Canopy bottom Fuselage.

10.Canopy top Fuselage.

HEINKEL HE 111- Item code:BH143. Instruction Manual

Temporary pin to

keep hinge centered.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

Aileron

1 2.Usingamodeling knife, removethecov-

ering servo tray.

13) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

14)Drill1,6mm pilotholesthroughthe block

of wood for each of the four mounting screws

provided with the servo.

Secure

Electric wire

Bottom side.

thread

Electric wire

HEINKEL HE 111- Item code:BH143. Instruction Manual

Repeat the procedure for the other

wing half.

o5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

Secure

Aileron controlhorn

INSTALLINGTHEAILERON CONTROL HORN.

3.INSTALLING THE AILERON

LINKAGES.

11. Working with the aileron linkage for

now, thread one clevis onto one of the

threaded wires.

12. Attach the clevis to the outer hole in the

control horn. Install a silicone tube on the

clevis.

Attach the clevis to the outer hole in the con-

trol horn.

100mm

A+B

Epoxy glue

Aileron

control horn

Snapkeeper.

bend

HEINKEL HE 111- Item code:BH143. Instruction Manual

Cut.

13. Plug the aileron servo into the receiver

andcenter theservo. Installthe servoarm onto

the servo. The servo arm should be perpen-

dicular to the servo and point toward the mid-

dle of the wing.

14. Locate one nylon servo arm, and using

wire cutters,remove all but one of the arms.

Using a 2mm drill bit, enlarge the third hole

out from the center of the arm to accommo-

date the aileron pushrod wire.

15.Usingpliers,carefullymake a 90 degree

bend down at the mark made. Cut off the ex-

cess wire, leaving about 4mm beyond the

bend.

16.Insert the90 degree bend down through

the hole in the servo arm. Install one nylon

snap keeper over the wire to secure it to the

arm.Install theservoarm retainingscrewand

remove the masking tape from the aileron. Repeat the procedure for the other wing

half.

Bottom side.

II. FLAP.

1.INSTALLING THE FLAP SERVOS.

Servostray

HEINKEL HE 111- Item code:BH143. Instruction Manual

2x10mm.

Electric wire

Flap controlhorn

2.INSTALLINGTHEFLAP CONTROLHORN.

A+B Epoxy

PLUS glue

Secure.

Flap

control

Installing the flap linkages as pictures

below.

3. INSTALLING THE FLAP

LINKAGES.

3.INSTALLING THE FLAP

LINKAGES.

Bend.

100mm

Snapkeeper.

HEINKEL HE 111- Item code:BH143. Instruction Manual

Repeat the procedure for the other wing

half.

OPTION 1. ELECTRIC MOTOR.

3x15mm.

THERE ARE TWO OPTIONS:

1. ELECTRIC MOTOR

2. ENGINE MOUNT.

INSTALLING THE ENGINE MOUNT.

Top side

bottom side

Cut.

Flap.

HEINKEL HE 111- Item code:BH143. Instruction Manual

Secure.

INSTALLING RETRACTABLE LANDING

GEAR

3x15mm

Secure.

Drill a hole 3.8mm

diameter.

3x15mm

Other manuals for HEINKEL HE 111

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model Extra 300S User manual

Black Horse Model

Black Horse Model BH36-A Owner's manual

Black Horse Model

Black Horse Model EXTRA 300 Owner's manual

Black Horse Model

Black Horse Model SUPER DECATHLON Owner's manual

Black Horse Model

Black Horse Model Fieseler Fi156C STORCH User manual

Black Horse Model

Black Horse Model Extra 300S Owner's manual

Black Horse Model

Black Horse Model CHIPMUNK BH44 Owner's manual

Black Horse Model

Black Horse Model PZL-104 WILGA BH 124 Owner's manual

Black Horse Model

Black Horse Model dornier DO335 Owner's manual

Black Horse Model

Black Horse Model RYAN 61 Owner's manual

Black Horse Model

Black Horse Model Matrix Owner's manual

Black Horse Model

Black Horse Model Shark BH119 Owner's manual

Black Horse Model

Black Horse Model Focke-Wulf FM 190A Owner's manual

Black Horse Model

Black Horse Model SPACE WALKER Owner's manual

Black Horse Model

Black Horse Model SU 26M-EP Owner's manual

Black Horse Model

Black Horse Model BH 105 Owner's manual

Black Horse Model

Black Horse Model MINIMOA Owner's manual

Black Horse Model

Black Horse Model P- 47 THUNDERBOLT- EP Owner's manual

Black Horse Model

Black Horse Model SPEED AIR-40 Owner's manual

Black Horse Model

Black Horse Model PC-9 ARF BH79 Owner's manual

Black Horse Model

Black Horse Model CHIPMUNK Owner's manual

Black Horse Model

Black Horse Model SBACH 342 Owner's manual

Black Horse Model

Black Horse Model WIlD HOTS User manual

Black Horse Model

Black Horse Model BH136A Owner's manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual