Black Horse Model SU 26M-EP Owner's manual

SPECIFICATION

Instruction Manual book

MadeinVietnam.



Wingspan : 1,140 mm 44.88 in.



Length : 1,063 mm 41.85 in.



Weight : 1.4 kg 3.08 Lbs.



Radio : 04 channels.



Servo : 05miniservos(23.6x 11.6x 24mm)

0.92 x 0.45 x 0.94 in.



ElectricMotor :EMAX BL 2815/09.



Battery : 3Cells-Li-Poly-11.1V 2.200mAh.



Speedcontrol: 60A.



Propeller:11x 6

SU 26M-EP - Item code: BH97 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your SU 26M-EP. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelp thenew pilotonhiswayto successfulR/C flight.Theywillalsobe able

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landinggear.....

Toavoid scratching yournew airplane,do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftand toprotect thetable. Keepacouple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrialfitall theparts.Makesureyou have

the correct parts and that they fit and are

alignedproperlybefore gluing!Thiswill assure

proper assembly.SU 26M-EP ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderandacetone.Do notlet thesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevatorhalves.

SUGGESTION.

NOTE.

SU 26M-EP - Item code: BH97 . Instruction Manual

SAFETY PRECAUTION.

REPLACEMENT LARGE PARTS

B. Wing panel.

C. Fuselage.

A.Cowling. D . Horizon stabilizer. F. Aluminium wing dihedral brace.

E.Vertical stabilizer.

REPLACEMENT SMALL PARTS

G. Decal sheet.

2. Wheels

1. Aluminium landing gear. 3.Spinner.

4. Plastic parts for bottom fuselage.

3. 4.

+ This is not a toy

+ Be sure that no other flyers are using your radio frequency.

+ The glow plug clip must be securely attached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from the propeller.

+ Do not start the motor if people are near. Do not stand in line with the side of the propeller.

SU 26M-EP - Item code: BH97 . Instruction Manual

 2)Using amodeling knife,remove thecov-

ering at possition show below.

 1) Install the rubber grommets and brass

eyelets onto the aileron servos.

I. AILERON.

 4. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

 3. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

C/Aglue

Aileron Bottom of wing.

Electric wire

thread

Aileron Bottom side

C/Aglue

1.INSTALLING THE AILERON SERVOS.

SU 26M-EP - Item code: BH97 . Instruction Manual

1) Using a ruler & pen to draw a straight

line as below picture.

 5. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Repeat the procedure for the other wing

half.

INSTALLING THE AILERON

CONTROL HORN.

INSTALLING THE AILERON

LINKAGES.

Servo

Secure.

C/Aglue

Cut.

Repeat the procedure for the other wing

half.

Control horn.

Micro control

connector. Control horn.

Pushrod wire.

SU 26M-EP - Item code: BH97 . Instruction Manual

See pictures below:

INSTALLING ELECTRIC MOTOR.

Drill a hole

5mmdiameter

Cut.

150 mm

Secure

Right side.

PARTSREQUIRED

MAIN GEAR INSTALATION.

Secure

Landing

gear.

24 mm

3 x 40 mm

SU 26M-EP - Item code: BH97 . Instruction Manual

Secure

2. While keeping the back edge of the

cowl flush with the marks, align the front of

thecowlwith thecrankshaftofthe engine. The

front of the cowl should be positioned so the

crankshaft is in nearly the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

 1. Slide the fiberglass cowl over the en-

gineand lineupthe backedgeof thecowlwith

the marks you made on the fuselage.

COWLING.

Bottom side

3. Slide the cowl back over the engine

andsecure itin placeusingfour woodscrews.

See picture below.

4. Installthemufflerandmufflerextension

onto the engine and make the cutout in the

cowl for muffler clearance. Connect the fuel

and pressure lines to the carburetor, muffler

andfuel fillervalve.

Trim and

cut.

Machine screw.

Left side.

3 x 10 mm

Top side

Front view.

SU 26M-EP - Item code: BH97 . Instruction Manual

Installthe spinnerbackplate,propeller and

spinner cone. The spinner cone is held in

place using two 3mm x 12mm wood screws.

INSTALLING THE SPINNER.

Secure.

 1. Install the rubber grommets and brass

colletsinto theelevatorservo.Testfitthe servo

into the servo tray.

 2. Mount the servo to the tray using the

mountingscrews providedwithyour radiosys-

tem.

SERVO ELEVATOR AND RUDDER

See pictures below:

Bottom side

HORIZONTAL STABILIZER.

SU 26M-EP - Item code: BH97 . Instruction Manual

 1. Draw a center line onto the horizontal

stabilizer. Then slide the horizontal into the

fuselage.

 2 Using a modeling knife, cut away the

covering from the fuselage for the stabilizer

and remove it.

C/Aglue

 3. Markthe shapeof thevertical onthe left

and right sides onto the horizontal stabilizer

using a felt-tip pen

Markline

Center line.

 4. Remove the stabilizer. Using the lines

youjust drewas aguide, carefullyremove the

coveringfrom betweenthemusing amodeling

knife.

When cutting through the covering to re-

move it, cut with only enough pressure to

only cut through the covering it’s self. Cut-

ting into the balsa structure may weaken

it. This could lead to possible failure dur-

ing flight.

Remove

covering.

SU 26M-EP - Item code: BH97 . Instruction Manual

6. Afterthe epoxy has fully cured, remove

the masking tape or T-pins used to hold the

stabilizer in place and carefully inspect the

glue joints. Use more epoxy to fill in any

gaps that were not filled previously and

clean up the excess using a paper towel and

rubbingalcohol.

Epoxy

glue.

Epoxyglue.

C/A glue.

C/Aglue.

C/Aglue

 5. When you are sure that everything is

aligned correctly, mix up a generous amount

of 30 minute epoxy. Apply a thin layer to the

topand bottomof thestabilizer mountingarea

and to the stabilizer mounting platform sides

inthefuselage. Slidethestabilizerin placeand

re-align. Double check all of your measure-

ments one more time before the epoxy cures.

Remove any excess epoxy using a paper

towel and rubbing alcohol and hold the stabi-

lizer in place with T-pins or masking tape.

Check to mark sure the wing and stabi-

lizer are paralell. If they are not, lightly sand

theopening inthe fuselagefor thestabilizer

until the stabilizer is paralell to the wing.

This manual suits for next models

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model B-25J Mitchell Owner's manual

Black Horse Model

Black Horse Model HEINKEL HE-112B Owner's manual

Black Horse Model

Black Horse Model BH136A Owner's manual

Black Horse Model

Black Horse Model Edge 540-V3 Owner's manual

Black Horse Model

Black Horse Model Excel 2000 Owner's manual

Black Horse Model

Black Horse Model PC-9 Owner's manual

Black Horse Model

Black Horse Model L-39 Albatros Owner's manual

Black Horse Model

Black Horse Model RYAN 61 Owner's manual

Black Horse Model

Black Horse Model Blade BH 70 Owner's manual

Black Horse Model

Black Horse Model Liberty 182II User manual

Black Horse Model

Black Horse Model P47 Thunderbolt Owner's manual

Black Horse Model

Black Horse Model PZL-104-WILGA User manual

Black Horse Model

Black Horse Model CAP 232-EP Owner's manual

Black Horse Model

Black Horse Model P47 Thunderbolt Owner's manual

Black Horse Model

Black Horse Model PC-9 ARF BH79 Owner's manual

Black Horse Model

Black Horse Model Twister Owner's manual

Black Horse Model

Black Horse Model Sprinter User manual

Black Horse Model

Black Horse Model YAK 55M Owner's manual

Black Horse Model

Black Horse Model Edge 540-V3 Owner's manual

Black Horse Model

Black Horse Model RYAN BH 72 Owner's manual

Black Horse Model

Black Horse Model KATANA bh27 Owner's manual

Black Horse Model

Black Horse Model BH167 Owner's manual

Black Horse Model

Black Horse Model GILMORE BH179 Owner's manual

Black Horse Model

Black Horse Model MESSERSCHMITT BF-109E BH146 User manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual