Black Horse Model Shark BH119 Owner's manual

SPECIFICATION
Instruction Manual book


Wingspan : 1,800 mm 70.87 in.


Length : 1,560 mm 61.42 in.


Weight : 4.8 kg 10.56 Lbs.


Radio : 08 channels.


Servo : 09 servos.


Engine : 75 2 stroke.
20 CC Gas
MadeinVietnam.
ElectricMotor: RIMFIRE 1.20.
Battery:18.5 -22.2V(5-6SLIPO)
Propeller: 16x6
Speed control: 80A.
Item code:BH119

2
SHARK - Item code: BH119 . INSTRUCTION MANUAL
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybeforestarting assemblyof your SHARK.Use theparts listingbelow toidentify
all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthe new pilotonhiswaytosuccessfulR/C flight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournew airplane, donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotect the table.Keep acouple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitallthe parts.Make sureyouhave
the correct parts and that they fit and are
alignedproperlybefore gluing!Thiswillassure
proper assembly. SHARK ARF is hand made
from natural materials, every plane is unique
andminor adjustmentsmay haveto bemade.
However, you should find the fit superior and
assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone.Donotlet these chemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.

3
SHARK - Item code: BH119 . INSTRUCTION MANUAL
Caution: this model is not a toy!
Ifyou area beginnerto this type of poweredmodel, pleaseask anexperienced modelflyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhave to carry out isimportant andmust bedone carefully.The model willonly bestrong andfly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning pro-
peller.
SAFETY PRECAUTION.

4
SHARK - Item code: BH119 . INSTRUCTION MANUAL
A.
B. B.
C.
G.
D.
E.
F.
REPLACEMENT LARGE PARTS
F. Aluminium wing dihedral brace.
E. Rudder
G. Decal sheets.
A.Cowling.
B. Wing panel.
C. Fuselage.
D . Horizontal stabilizer. REPLACEMENT SMALL PARTS
1. 1.
3. 9
13.
12.
4.
7.
8.
10.
11.
14.
2. 2.
3.
6.
5.

5
SHARK - Item code: BH119 . INSTRUCTION MANUAL
3. Wheels.
13. Fuel tank.
12.Plastic parts for elevator and rudder pushrod.
9.Spinner.
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
2. Usinga modeling knife, remove thecov-
ering servo tray.
C/Aglue
2.Air retract main gear.
1.Door mounting wheel.
4.Air retract nose gear.
5.Valvecontrol.
6.Valveone way.
14.Engine mount ply of wood .
7.3 way connectors.
10.Air tank.
8.4 way connector.
11.Air line sets.
C/Aglue
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Aileron
Bottom side

6
SHARK - Item code: BH119 . INSTRUCTION MANUAL
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4.Drill 1,5mm pilot holes throughthe block
of wood for each of the four mounting screws
provided with the servo. Install servo into ai-
leron servo tray as same as picture below.
Remove
covering
Secure
Electric wire
servotray
Repeat the procedure for the other wing
half.
INSTALLINGTHEAILERON CONTROLHORN.
Aileroncontrolhorn
2x10mm.
Secure.
Electric wire Thread

7
SHARK - Item code: BH119 . INSTRUCTION MANUAL
Control horn of
theaileron.
A+B Epoxy
PLUS glue
AB
A+B Epoxy
PLUS glue
Installing the aileron linkages as pictures
below.
Flap
1.INSTALLING THE FLAP SERVOS.
II. FLAP.
Repeat the procedure for the other wing
half.
INSTALLING THE AILERON
LINKAGES.
55mm
M2 M2 lock nut
Electric wire Thread

8
SHARK - Item code: BH119 . INSTRUCTION MANUAL
Secure.
2.INSTALLING THE FLAP CONTROL HORN.
Flap controlhorn
2x10mm.
A+B Epoxy
PLUS glue
Flap control
horn.
Installing the flap linkages as pictures
below.
3. INSTALLING THE FLAP
LINKAGES.
Repeat the procedure for the other wing
half.
55 mm
M2 M2 lock nut
PARTSREQUIRED
Bottom side
INSTALLING RETRACTABLE
LANDING GEAR.

9
SHARK - Item code: BH119 . INSTRUCTION MANUAL
Secure.
3x15mm
5x30mm

10
SHARK - Item code: BH119 . INSTRUCTION MANUAL
Secure
Drill a hole
3mm diameter
Drill a hole
3mm diameter
3x6mm
3x6mm 3x6mm