Black Horse Model P-36A Hawk User manual

SPECIFICATION
1Wingspan : 1,600 mm 63.in.
1Length : 1,300 mm 52.in.
1Weight : 3.9 kg 8.58 lbs.
Partslistingrequired(notincluded):
1 Engine : 61 cu.in - 2stroke;
15 CC Gas.
1Servo : 8 Servos + 2 servos Retract (HITEC HS-75BB).
1 Radio : 8 channels.
Instruction Manual Book
MadeinVietnam.
ITEM CODE:BH41-A

P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your P- 36A HAWK. Use the parts listing below to
identifyallparts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplierandjoinyourlocalR/CModelFlyingClub.R/CModelFlyingClubsofferavarietyoftraining
proceduresdesignedtohelpthenewpilotonhisway tosuccessfulR/Cflight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
4Thick cyanoacrylate glue.
430 minute epoxy.
45 minute epoxy.
4Hand or electric drill.
4Assorted drill bits.
4Modellingknife.
4Straightedgeruler.
42mm ball driver.
4Phillips head screwdriver.
4220 grit sandpaper.
490° square or builder’s triangle.
4Wire cutters.
4Masking tape & T-pins.
4Thread-lock.
4Paper towels.
Some more parts.
HARDWARE PACK
COWLING.
Landinggear.....
To avoid scratching your new airplane, do
not unwrap the pieces until they are needed
for assembly. Cover your workbench with an
old towel or brown paper, both to protect the
aircraftandtoprotect the table. Keep a couple
of jars or bowls handy to hold the small parts
after you open the bag.
Please trial fit all the parts. Make sure you
havethe correct partsand that theyfit and are
alignedproperlybeforegluing!Thiswill assure
proper assembly. P- 36A HAWK ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit
superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the
following: paint thinner, C/A glue accelerator,
C/A glue debonder and acetone. Do not let
these chemicals come in contact with the
colors on the covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
4(1) Fuselage.
WING ASSEMBLY
4(1) Right wing half with pre-installed
aileron.
4(1) Left wing half with pre-installed
aileron.
4Some more parts........
Tail section assembly
4(1) Vertical stabilizer with pre-
installedrudder.
4(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.

3
P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+Do not smoke near fuel.
+Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning pro-
peller.
SAFETY PRECAUTION.
REPLACEMENT LARGE PARTS
B. Wing panel.
A.Cowling.
C. Fuselage.
D . Horizontal stabilizer.
F. Aluminium wing dihedral brace.
E. Rudder.
G. Decal sheet.
B.
C.
B.
D.
D.
E.
F.
A.
G.

P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
4
REPLACEMENT SMALL PARTS
3.Wheels.
5. Tail gear set.
2.Retract main gear.
4. Fuel tank.
1.Door mounting wheel.
11) Install the rubber grommets and brass
eyelets onto the aileron servos.
1.INSTALLING THE AILERON SERVOS.
I.AILERON.
6. Plastic parts for elevator and rudder
pushrod.
7. Plastic part for tail gear.
8.Tile wrap
Aileron.
Flap. Aileron.
2. 1. 1.
3. 2.
4.
5.
6.
7.
8.
3 x 10mm.
3 x 10mm.
53x12mm

5
P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
12) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
13)Drill1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
o4. Instal servo tray with aileron servo into
the wing as same as picture below.
Repeat the procedure for the other wing
half.
2.INSTALLINGTHEAILERON CONTROLHORN
.
Thread.
Electric wire
Secure
Bottom side
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
Cutthecovering
awayfrom theslot.
Installaileron control hornas same as
picturebelow.
3 x 20 mm.

P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
6
Repeat the procedure for the other wing
half.
Aileron
control horn.
INSTALLING THE AILERON
LINKAGES.
2 x 8mm
2x8mm.
58 mm.
Repeat the procedure for the other wing
half.
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
Aileron
control horn.
Secure.
Secure.
Thread

7
P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
2.INSTALLING THE FLAP CONTROL HORN.
3 x 15 mm.
Secure.
Secure.
Electric
wire
Flap control
horn.
C/Aglue.
C/Aglue.
Bottom of wing.
C/Aglue.
C/Aglue.

P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
8
Installing the aileron linkages as pictures
below.
3.INSTALLING THE FLAP LINKAGES. INSTALLING RETRACTABLE
LANDING GEAR.
2 x 8mm
2x8mm.
58 mm.
Secure.
3 x 15mm. 3 x 15mm.
Repeat the procedure for the other wing
half.
bottomof wing.
Flap Aileron
Markpoint.

9
P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
Markpoint.
Secure.
Secure.
Drill a hole
2mmdiameter
3 x 15mm.
Push.

P- 36A HAWK-Item code BH41-A. INSTRUCTION MANUAL.
10
Secure.
Secure.
Servo for retractable only.
connector.