Black Horse Model Landscape Owner's manual

SPECIFICATION
MadeinVietnam.


Wingspan : 1,940 mm 76.38 inches.


Length : 1,700mm 66.93 inches.


Weight : 5.8 kg 12.76 lbs.


Radio : 6 channels.


Servo : 8 servos.


GlowEngine : 26- 30ccgas.
Instruction Manual book
ITEM CODE:BH101.

2
LANDSCAPE - Item code: BH101A.Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your LANDSCAPE. Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalso beable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournew airplane,donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotect thetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitalltheparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswillassure
proper assembly. LANDSCAPE ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone. Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
LANDSCAPE - Item code: BH101A.Instruction Manual
Caution: this model is not a toy!
Ifyouare abeginner tothis typeofpowered model,please askan experiencedmodelflyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution!donot heatthe film morethan isabsolutely necessary. Iftheair orthe ironistoo hot,the
film may melt and holes may be formed.
Thismodelis highlypre-fabricated andcanbe builtin averyshort time.However,thework which
you have to carry out is important and must be done carefully. The model will only be strong and
fly well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to
prevent them shaking loose: just squirt white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+Makeengine adjustmentsfrombehindthe propelleronly.Donotreacharoundthespinningpropeler.
SAFETY PRECAUTION.
C.
F1.
B2.
D2.
A.
D1.
B1.
G.Decal sheet.
E.
E.Rudder. G.
A.Cowling.
B. Wing panel.
C.Fuselage
D.Horizontal stabilizer.
F1.Aluminiumtube wing
dihedral brace.
F2.Aluminium tube
Horizontal stabilizer.
K.Pilot.
K
F2

4
LANDSCAPE - Item code: BH101A.Instruction Manual
3. Drill 1,5mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo. Install servo into ai-
leron servo tray as same as picture below.
2. Wheels.
8. Wheel pants.
7. Plastic parts for landing gear.
4. Plastic parts for rudder pushrod.
3. Plastic part for nose gear.
5. Nose gear set.
10.Spinner.
 1. Install the rubber grommets and brass
eyelets onto the aileron servo.
2.Usinga modelingknife,remove thecov-
ering servo tray.
6.Engine mount ply of wood .
Remove
covering
Servo tray.
1. Aluminium landing gear.
9. Fuel Tank.
2.
7.
9.
1. 3.
8.
6.
1. 4.
5.
10.
Aileron.
Flap.
Bottom side.
I. INSTALLING THE AILERON-FLAP
SERVO
INSTALLING THE AILERON SERVOS.

5
LANDSCAPE - Item code: BH101A.Instruction Manual
4. Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
Repeat the procedure for the other wing
half.
Repeat the procedure for the other wing
half.
Installing the aileron linkages as pictures
below.
Attach the clevis to the outer hole in the con-
trol horn.
INSTALLINGTHEAILERON CONTROLHORN
Secure.
2x10mm.
Installaileron controlhornas sameas
picturebelow.
INSTALLING THE AILERON
LINKAGES.
75 mm
Electricwire
Bottom side.
Secure.
A+B Epoxy
PLUSglue.
Aileron
Control
horn.

6
LANDSCAPE - Item code: BH101A.Instruction Manual
INSTALLING THE FLAP CONTROL HORN.
INSTALLING THE FLAP SERVO.
2x10mm.
INSTALLING THE FLAP LINKAGES.
Installing the aileron linkages as pictures
Control horn of
theflap.
Electric
wire
Thread
Secure.
75 mm

7
LANDSCAPE - Item code: BH101A.Instruction Manual
Repeat the procedure for the other wing
half.
Flap.
Bottom side
INSTALLING THE ENGINE MOUNT
NOSE GEAR.
See pictures below:
Drilla hole
4mmdiameter.

8
LANDSCAPE - Item code: BH101A.Instruction Manual
wire cable.
wire cable.
Secure.
SERVO NOSE GEAR INSTALLATION.
servo nose
gear.
servonose gear.

9
LANDSCAPE - Item code: BH101A.Instruction Manual
INSTALLING THE STOPPER ASSEMBLY
FUEL TANK.
1. The stopper has been pre-assembled at
the factory.
2.Using amodeling knife,cut onelength of
siliconfuelline (thelength ofsilicon fuellineis
calculated by how the weighted clunk should
restabout 8mmaway fromtherearofthetank
andmove freelyinside thetank). Connectone
end of the line to the weighted clunk and the
otherend tothenylonpickuptubein thestop-
per.
When the stopper assembly is installed
in the tank, the top of the vent tube should
rest just below the top surface of the tank.
It should not touch the top of the tank.
3.Carefullybendthe secondnylon tubeup
ata 45degreeangle (usingacigarettelighter).
This tube will be the vent tube to the muffler.
4.Carefullybendthe thirdnylon tubedown
ata 45degreeangle (usingacigarettelighter).
This tubewill bevent tubeto thefuelingvalve.
Secure.
Secure.

10
LANDSCAPE - Item code: BH101A.Instruction Manual
6. When satisfied with the alignment of the
stopper assembly tighten the 3mm x 20mm
machine screw until the rubber stopper ex-
pandsand sealsthetank opening.Do notover
tighten the assembly as this could cause the
tank to split.
7. Using a modeling knife, cut 3 lengths of
fuel line 150mm long. Connect 2 lines to the 2
vent tubes and 1 line to the fuel pickup tube in
the stopper.
 8. Feed three lines through the fuel tank
compartment and through the pre-drilled hole
in the firewall. Pull the lines out from behind
the engine, while guiding the fuel tank into
place. Push the fuel tank as far forward as
possible,the frontofthetankshould justabout
touch the back of the firewall.
Do not secure the tank into place perma-
nently until after balancing the airplane.
You may need to remove the tank to mount
the battery in the fuel tank compartment.
Blow through one of the lines to ensure
the fuel lines have not become kinked inside
the fuel tank compartment. Air should flow
througheasily.
9. To secure the fuel tank in place, apply a
bead of silicon sealer to the forward area of
thetank, whereit exitsthefuselage behindthe
enginemountingbox andtotherearofthetank
at the forward bulkhead.
 5. Test fit the stopper assembly into the
tank. It may be necessary to remove some of
the flashing around the tank opening using
amodeling knife. Ifflashing is present, make
sure none of it falls into the tank.
Vent tube Fuel pick- up tube
Fuelfilltube
Secure.
Fueltank.
Tygon gas tubing not included.

11
LANDSCAPE - Item code: BH101A.Instruction Manual
Throttle
cable.
Mount ply of
wood .
3x12mm
Secure.
Right side
INSTALLING THE THROTTLE CABLE.
Throttle cable.
Throttleservo.

12
LANDSCAPE - Item code: BH101A.Instruction Manual
Secure.
2. While keeping the back edge of the
cowl flush with the marks, align the front of
thecowlwiththecrankshaftoftheengine. The
front of the cowl should be positioned so the
crankshaft is in nearly the middle of the cowl
opening. Hold the cowl firmly in place using
pieces of masking tape.
4. Installthemufflerandmufflerextension
onto the engine and make the cutout in the
cowl for muffler clearance. Connect the fuel
and pressure lines to the carburetor, muffler
andfuel fillervalve.
3. Slide the cowl back over the engine
andsecure itin placeusing fourwood screws.
See picture below.
Machine screw.
Left side.
Trim and cut
Bottom side.
1. Slide the fiberglass cowl over the en-
gineand lineup thebackedgeofthe cowlwith
the marks you made on the fuselage.
COWLING.
Bottom side.
3 x 12mm
Left side

13
LANDSCAPE - Item code: BH101A.Instruction Manual
C/A glue.
Front view.
Installthe spinnerbackplate,propellerand
spinner cone. The spinner cone is held in
place using two 3mm x 12mm machine
screws.
INSTALLING THE SPINNER.
Secure.
Secure.
PARTSREQUIRED
MAIN GEAR INSTALATION.
1)Assembleand mountingthewheel pants
as shown in the following pictures.
Drill 8mm
hole.
1. 1.
8. 8.
2.
7. 7.

14
LANDSCAPE - Item code: BH101A.Instruction Manual
Secure.
Secure.
Silicon.
Silicon.
Plastic parts for landing
gear.
Remove
covering.
Cut.
Landinggear.

15
LANDSCAPE - Item code: BH101A.Instruction Manual
Secure.
Mark line.
Repeat the process for the other wheel.
Epoxyglue.
C/Aglue
Bottom side.
1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the
servo into the servo tray.
2. Mount the servo to the tray using the
mounting screws provided with your radio
system.
INSTALLING THE ELEVATOR
SERVOS.
Remove
covering
Elevator servo

16
LANDSCAPE - Item code: BH101A.Instruction Manual
HORIZONTAL STABILIZER.
282mm
9mm
3x12 mm.
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
Aluminium
Elevator servo.
ELEVATOR CONTROL HORN INSTALLA-
TION.
Secure.
3 x 12mm
Secure.

17
LANDSCAPE - Item code: BH101A.Instruction Manual
Elevator
Controlhorn.
Elevator
Controlhorn.
 Elevator pushrod install as same as the
way of aileron pushrod.
ELEVATOR PUSHDROD
INSTALLATION
Elevator
pushrod
Rudder servo install as same as method of
elevator servo. See picture below:
RUDDER SERVOS INSTALLATION.
Elevator
pushrod
Elevator
pushrod
Elevator pushrod
A+ B Epoxy
PLUSglue
Rudder servo
M2
M3

18
LANDSCAPE - Item code: BH101A.Instruction Manual
Rudder servo
See pitures bellow.
RUDDER SERVOS INSTALLATION.
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ControlhornofRudder.
RUDDER CONTROL HORN INSTALLA-
TION.
Aluminium
Cut.
A+BEpoxy
PLUSglue.

19
LANDSCAPE - Item code: BH101A.Instruction Manual
A+B Epoxy
PLUSglue
 1. Rudder pushrod install as same as
the way of aileron control horn.
Rudder
controlhorn
RUDDER PUSHROD INSTALLATION.
Rudder
pushrod
Rudder pushrod
Elevator pushrod
Plastic parts of pushrod.
Cut.
M2
M2

20
LANDSCAPE - Item code: BH101A.Instruction Manual
Elevator
pushrod.
Elevator
pushrod.
Bottom side.
Rudder
pushrod.


1. Cutout theswitch holeusingamodeling
knife. Use a 2mm drill bit and drill out the two
mounting holes through the fuselage side.


2. Secure the switch in place using the
two machine screws provided with the radio
system.
INSTALLING THE SWITCH.
Switch of Engine
Switch
C/Aglue
C/Aglue.
Switch of
Receiver