Black Horse Model Spitfire MK Owner's manual

Instruction Manual book
SPECIFICATION


 Wingspan : 2,000mm 78.74 in.


 Length : 1,760 mm 69.29 in.


 Weight : 6.8kg 14.96 Lbs.
Parts listing required (not included).


 Engine : 0.S GT 33cc gas


 Radio : 07 channels.


 Servo : 09 Standard high torque servos.
Made in Vietnam.
ITEM CODE:BH 136

2
SPITFIRE MK Item code: BH136 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your
SPITFIRE MK. Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Cowling
Landing gear.....
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craft and to protect the table. Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installed rudder.
(1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.
Please trial fit all the parts. Make sure you have
the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly.SPITFIRE MKARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing: paint thinner, C/A glue accelerator, C/A glue
debonder and acetone. Do not let these chemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
SPITFIRE MK Item code: BH136 . Instruction Manual
Caution:
this model is not a toy!
If you are a beginner to this type of powered model, please ask an experienced model flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
you have to carry out is important and must be done carefully. The model will only be strong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning pro-
peller.

4
SPITFIRE MK Item code: BH136 . Instruction Manual
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
2.Door mounting wheels
3. Wheels
6.Fuel tank
14. Antenna.
1. Air retract main gear.
11.3 way connector.
9.Valve one way.
10.Valve control.
15.Tail gear set.
12.Spinner
8. Air tank.
4.Air line sets.
7. Battery tray.
16.Plastic parts for top wing
17.Gun sets
13.Plastic parts for bottom wing
A. Cowling.
F2. Aluminium tube
Horizontal stabilizer.
B. Wing panel(B1,B2).
C Fuselage.
D.Horizontal stabilizer(D1,D2).
E. Rudder.
F1. Aluminium tube wing
dihedral brace.
G. Decal sheet.
K.Pilot
K
5.Springs
3x15mm.
5x40mm.
5x50mm.
3x15mm.

5
SPITFIRE MK Item code: BH136 . Instruction Manual
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Top side
Bottom side
Aileron
2) Using a modeling knife, remove the cov-
ering at possition show below.
Servo tray.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4) Drill 1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
Remove
covering
Servo tray.
Secure.

6
SPITFIRE MK Item code: BH136 . Instruction Manual
Repeat the procedure for the other wing
half.
Aileron control horn
5. Instal servo tray with aileron servo into
the wing as same as picture below.
thread
Electric
wire.
2x10mm.
Secure.
A+B Epoxy
PLUS glue
Installing the aileron linkages as pictures
below.
INSTALLING THE AILERON
LINKAGES.
Aileron
control horn
75mm. 3x10mm.
INSTALLINGTHEAILERONCONTROLHORN.

7
SPITFIRE MK Item code: BH136 . Instruction Manual
Repeat the procedure for the other wing
half.
Secure
II. FLAP
1.INSTALLING THE FLAP SERVO
Flap.
Flap.
Bottom side
2x10mm.
Secure.
Electric
wire.
Bottom side

8
SPITFIRE MK Item code: BH136 . Instruction Manual
Install flap control horn as same as
picture below.
A+B Epoxy
PLUS glue
Installing the flap linkages as pictures
below.
3.INSTALLING THE FLAP
LINKAGES.
Control horn
of the flap.
Control horn Flap.
2.INSTALLING THE FLAP
CONTROL HORN.
Secure.
Bottom side.
75mm 3x10mm.
4x12mm

9
SPITFIRE MK Item code: BH136 . Instruction Manual
Secure
PARTSREQUIRED
Repeat the procedure for the other wing
half.
INSTALLING AIR RETRACTABLE
LANDING GEAR.
3x15mm
3x15mm
5x40mm 5x40mm
1.
2.
2.
a.
b. a.
b.
4.
3.
a.
Drill a hole
2mm diameter.
hole 2mm.
Spring.
Spring.

10
SPITFIRE MK Item code: BH136 . Instruction Manual
Secure.
5x40mm
Secure.