BLADEZ prisma Supra User manual

OWNER’S MANUAL
ASSEMBLY OPERATION MAINTENANCE
WARRANTY PARTS ORDERING
CAUTION: Exercise of a strenuous nature, as is customarily done on this equipment, should not be
undertaken without first consulting a physician. No specific health claims are made or implied as they
relate to the equipment.
IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s
manual for future reference.
Prisma Supra folding treadmill
BH North America Corporation • www.bhnorthamerica.com
20155 Ellipse • Foothill Ranch • CA • 92610

TABLE OF CONTENTS
Treadmill Lubrication............................…… 3
Target Heart Rate…......................................4
Assembly Instructions…………………..........9
Installation…………………….......................15
Treadmill Operations……………..................18
Storage……………………...........................14
Troubleshooting……..…………………….…..23
Exploded View ………...................................24
Parts List …………………..............................25
Safety……………..........................….….......1
Warranty……..………………………...............28
Training….....................................................5
Additional Maintenance……………..............22
.

IMPORTANT SAFETY ADVICE
PRECAUTIONS
This treadmill has been designed and constructed to provide maximum safety. Nevertheless,
certain precautions should be taken when using exercise equipment. Read the whole manual
before assembling and using the treadmill. The following safety precautions should also be
observed:
1. Keep children or pets away from this equipment at all times. DO NOT leave them
unsupervised in treadmillthe room where this is kept.
2. It can only be used by one person at a time.
3. If you experience dizziness, nausea, chest pains or any other symptom while using this
appliance STOP the exercise. SEEK MEDICAL ATTENTION IMMEDIATELY!
4. Keep your hands well away from any of the moving parts.
5. Wear clothing suitable for doing exercise. Do not use baggy clothing that might get caught
up in the treadmill. Always wear running shoes or trainers when using the machine.
6. This appliance must only be used for the purposes described in this manual. DO NOT use
accessories that are not recommended by the manufacturer.
7. Do not place sharp objects near the machine.
8. Disabled people should not use the machine without the assistance of a qualified person or
a doctor.
9. Do warm up stretching exercises before using the equipment.
10. Do not use the if it is not working correctly.treadmill
11. Review all the warnings affixed to the machine and replace all the labels if damaged, illegible,
12. Functional and visual inspections of the equipment shall be made after assembly is complete,
or removed. You can obtain the labels from Parts & Service location.
KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE
and thoroughly inspect for proper assembly.
WARNING: Before beginning any exercise program consult your physician. This is especially important for individuals
over the age of 35 years of age or persons with pre-existing health problems. Read all instructions before using any
fitness equipment. We assume no responsibility for personal injury or property damage sustained by or through the use
of this product.
1

IMPORTANT SAFETY ADVICE (Cont’d)
KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE
14. The should only be used for the home. Not meant for commercial use.treadmill
15. This treadmill is not suitable for therapeutic use. Consult a physician prior to starting an
exercise program.
16. This treadmill should only be used after a through review of the operation manual and the
warning label.
17.
This unit has been designed for home use. The weight of the user must not exceed 250 lbs.
(113 kg.)
18. Keep your hands well away from any of the moving parts.
19. Parents and/or those responsible for children should always take their curious nature into
account and how this can often lead to hazardous situations and behavior resulting in
accidents. Under no circumstances should this appliance be used as a toy.
20. The owner is responsible for ensuring that anyone who uses the machine is duly informed
about the necessary precautions.
21. Your unit can only be used by one person at a time.
22. Use suitable clothing and footwear. Make sure all laces/cords are tied correctly.
2
13. A perimeter distance of 3 feet / 1meter is required before operating the unit.
23. DO NOT put the treadmill on its side at anytime. Moving of the unit should only be done
per instructions on page 14 figure 9 and figure 10. Failure to follow these instructions
could result in personal injury

TREADMILL LUBRICATION
It is required that the deck be lubricated
Before first use and subsequently according
to the frequency of usage in the table below.
Remove excessive accumulations of dust,
dirt, and other substances from running deck. Use a
clean soft cloth.
Do not use cleaner under the running
Belt.
Pull up running belt, dispense lubricant on
Deck, and spread evenly.
0.5~4.0 Mile lubricate every 1 year
4.0~7.0 Mile lubricate every 6 months
7.0~10.0 Mile lubricate every 3 month
IMPORTANT!
Silicone lubricant is designed to reduce
friction between the treadmill belt and deck.
Proper and timely application of Silicone
lubricant will prevent excessive static
electricity build-up which can result in
electrical component failure in the unit’s
console and/or mechanical failure due to
excessive wear and tear.
Warning!
TREADMILL LUBRICATION.
Use the bottle of lubricant to lubricate the inside of the belt in order to keep
your unit in top condition and to ensure that friction between the belt and the
board is kept to a minimum (due to different running styles, always apply more
lubrication to the area where you place your feet during the exercise).
It is advisable to lubricate the base of the belt between the board and the belt
As often as suggested below. If the belt starts to slip after lubrication,
then check the tension of the belt. To tension the belt, take the 6mm
Allen key (23) and with the machine set to 2 mi/h turn screws (R & L) one turn in
a clockwise direction.
Fig.12
3
Avg Speed. Lubrication

TARGET HEART RATE
The old motto, “no pain, no gain”, is a myth that has been overpowered by the benefits of exercising
comfortably. A great deal of this success has been promoted by the use of heart rate monitors. With the proper
use of a heart rate monitor, many people find that their choice of exercise intensity is either too high or too low and
exercise is much more enjoyable by maintaining their heart rate in the desired benefit range.
To determine the benefit range in which you wish to train, you must first determine your Maximum Heart Rate.
This can be accomplished by using the following formula: 220 - User’s Age = Maximum Heart Rate. If you enter
your age during programming of the console the console will perform this calculation automatically. This is used
for the HR control programs. After calculating your Maximum Heart Rate, you can decide upon which goal you
would like to pursue. The two most popular reasons for, or goals of exercise, are cardiovascular fitness (training
for the heart and lungs) and weight control. The
black columns on the chart above represent the
Maximum Heart Rate for a person whose age is
listed at the bottom of each column. The training
heart rate, for either cardiovascular fitness or
weight loss, is represented by two different lines
that cut diagonally through the chart. A definition
of the lines’ goal is in the bottom left-hand corner
of the chart. If your goal is cardiovascular fitness
or if it is weight loss, it can be achieved by training
at 90% or 70%, respectively, of your Maximum
Heart Rate on a schedule approved by your
physician. Consult your physician before
participating in any exercise program.
With all Heart Rate Control treadmill, you may
use the heart rate monitor feature without using
the Heart Rate Control program.
4

TRAINING GUIDELINES
Exercise is one of the most important factors in the overall health of an individual. Listed among its
benefits are:
Increased capacity for physical work (strength endurance)
Increased cardiovascular (heart and arteries/veins) and respiratory efficiency
Decreased risk of coronary heart disease
Changes in body metabolism, e.g. losing weight
Delaying the physiological effects of age
Physiological effects, e.g. reduction in stress, increase in self-confidence, etc.
Basic Components of Physical Fitness
There are four all encompassing components of physical fitness and we need to briefly define each and
clarify its role.
Strength is the capacity of a muscle to exert a force against resistance. Strength contributes to power and
speed and is of great importance to a majority of sports people.
Muscular Endurance is the capacity to exert a force repeatedly over a period of time, e.g. it is the capacity
of your legs to carry you 10 Km/6.2mi without stopping.
Flexibility is the range of motion about a joint. Improving flexibility involves the stretching of muscles and
tendons to maintain or increase suppleness, and provides increased resistance to muscle injury or soreness.
Cardio-Respiratory Endurance is the most essential component of physical fitness. It is the efficient
functioning of the heart and lungs.
Aerobic Fitness
The largest amount of oxygen that you can use per minute during exercise is called your maximum
oxygen uptake(MVo2). This is often referred to as your aerobic capacity.
The effort that you can exert over a prolonged period of time is limited by your ability to deliver oxygen to
the working muscles. Regular vigorous exercise produces a training effect that can increase your aerobic
capacity by as much as 20 to 30%. An increased MVO2 indicates an increased ability of the heart to pump
blood, of the lungs to ventilate oxygen and of the muscles to take up oxygen.
Anaerobic Training
This means “without oxygen”and is the output of energy when the oxygen supply is insufficient to meet
the body’s long term energy demands. (For example, 100 meter /328ft. sprint).
The Training Threshold
This is the minimum level of exercise which is required to produce significant improvements in any
physical fitness parameter.
Progression
As your become fitter, a higher intensity of exercise is required to create an overload and therefore provide
continued improvement
Overload
This is where you exercise at a level above that which can be carried out comfortably. The intensity,
duration and frequency of exercise should be above the training threshold and should be gradually
increased as the body adapts to the increasing demands. As your fitness level improves, the training
threshold should be raised. Working through your program and gradually increasing the overload factor is
important.
5

Specifics
Different forms of exercise produce different results. The type of exercise that is carried out is specific both
to the muscle groups being used and to the energy source involved.
There is little transfer of the effects of exercise, i.e. from strength training to cardiovascular fitness. That is
why it is important to have an exercise program tailored to your specific needs.
Reversibility
If you stop exercising or do not do your program often enough, you will lose the benefits you have gained.
Regular workouts are the key to success.
Warm Up
Every exercise program should start with a warm up where the body is prepared for the effort to come. It
should be gentle and preferably use the muscles to be involved later.
Stretching should be included in both your warm up and cool down, and should be performed after 3-5
minutes of low intensity aerobic activity or callisthenic type exercise.
Warm Down or Cool Down
This involves a gradual decrease in the intensity of the exercise session. Following exercise, a large
supply of blood remains in the working muscles. If it is not returned promptly to the central circulation,
pooling of blood may occur in the muscles.
Heart Rate
As you exercise, the rate at which your heart beat increases. This is often used as a measure of the required
intensity of exercise. You need to exercise hard enough to condition your circulatory system, and increase
your pulse rate, but not enough to strain your heart.
Your initial level of fitness is important in developing an exercise program for you. If you are starting off,
you can get a good training effect with a heart rate of 110-120 beats per minute(BPM). If you are fitter, you
will need a higher threshold of stimulation.
To begin with, you should exercise at a level that elevates your heart rate to about 65 to 70% of your
maximum. If you find this is too easy, you may want to increase it, but it is better to lean on the
conservative side.
As a rule of thumb, the maximum heart rate is 220 minus your age. As you increase in age, your heart, like
other muscles, loses some of its efficiency. Some of its natural loss is won back as fitness improves.
The following table is a guide to those who are “starting fitness”.
Age 25 30 35 40 45 50 55 60 65
Target heart Rate
10Second Count 23 22 22 21 20 19 19 18 18
Beats per Minute 138 132 132 126 120 114 114 108 108
Pulse Count
The pulse count(on your wrist or carotid artery in the neck, taken with two index fingers)is done for ten
seconds, taken a few seconds after you stop exercising. This is for two reasons: (a) 10 seconds is long
enough for accuracy, (b) the pulse count is to approximate your BPM rate at the time you are exercising.
Since heart rate slows as you recover, a longer count isn’t as accurate.
6
TRAINING GUIDELINES (cont’d)

The target is not a magic number, but a general guide. If you’re above average fitness, you may work quite
comfortably a little above that suggested for your age group.
The following table is a guide to those who are keeping fit. Here we are working at about 80% of
maximum.
Age 25 30 35 40 45 50 55 60 65
Target heart Rate
10 Second Count 26 26 25 24 23 22 22 21 20
Beats per Minute 156 156 150 144 138 132 132 126 120
Don’t push yourself too hard to reach the figures on this table. It can be very uncomfortable if you overdo
it. Let it happen naturally as you work through your program. Remember, the target is a guide, not a rule, a
little above or below is just fine.
Two final comments:(1) don’t be concerned with day to day variations in your pulse rate, being under
pressure or not enough sleep can affect it;(2) your pulse rate is a guide, don’t become a slave to it.
Muscle Soreness
For the first week or so, this may be the only indication you have that you are on an exercise program.
This, of course, does depend on your overall fitness level. A confirmation that you are on the correct
program is a very slight soreness in most major muscle groups. This is quite normal and will disappear in a
matter of days.
If you experience major discomfort, you may be on a program that is too advanced or you have increased
your program too rapidly.
If you experience PAIN during or after exercise, your body is telling your something.
Stop exercising and consult your doctor.
What to Wear
Wear clothing that will not restrict your movement in any way while exercising. Clothes should be light
enough to allow the body to cool. Excessive clothing that causes you to perspire more than you normally
would while exercising, gives you no advantage. The extra weight you lose is body fluid and will be
replaced with the next glass of water you drink. It is advisable to wear a pair of gym or running shoes or
“sneakers”.
Breathing during Exercise
Do not hold your breath while exercising. Breathe normally as much as possible. Remember, breathing
involves the intake and distribution of oxygen, which feeds the working muscles.
Rest periods
Once you start your exercise program, you should continue through to the end. Do not break off halfway
through and then restart at the same place later on without going through the warm-up stage again.
The rest period required between strength training exercises may vary from person to person. This will
depend mostly on your level of fitness and the program you have chosen. Rest between exercises by all
means, but do not allow this to exceed two minutes. Most people manage with half minute to one minute
rest periods
7
TRAINING GUIDELINES (cont’d)

SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and
back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back, and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons, and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for both legs. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
1
2
3
4
5
8
TRAINING GUIDELINES (cont’d)

ASSEMBLY
If you are missing parts or require information on how to
operate this product please call [phone]
9

ASSEMBLY INSTRUCTIONS
Note: Assembly of this unit should take one person about 20 minutes to properly assemble.
Assembly Instruction
Take the unit out of the box and place it on the floor as shown Fig.0.
Make sure that all of the pieces are there:
(1) Main structure; (35) Side supports;(26) Allen key 6mm; (27) wrench with phillips screwdriver;
(28) Combination box wrench; (131) Main cable; (126) Safety key; (132) Bottle of
lubricant; (74) Screw M6*20; (90) Bolts M8*5; (101) Washers.
Fig.0
10
WARNINGS
the safety release mechanism and could result in personal injury.
Never place the treadmill on its side during assembly or transport. Doing so will impair

First, loosen the two top holding knobs (29) by two turns, counter-clockwise, Fig.1.
Next take hold of the handrails (9 and 10) and lift them in the direction of the arrow,
until you hear the top holding knobs (29) click into position, as shown in Fig.2.
Fig.1
Fig.2
11
ASSEMBLY INSTRUCTIONS (cont’d)

Loosen the bottom holding knobs by two turns (29), holding the handrails
(9 and 10), lift the upright bars in the direction of the arrow, until you hear the
bottom holding knobs (29) click into position.
Fig.3
Fig.4
12
ASSEMBLY INSTRUCTIONS (cont’d)

Once you have completed the above, tighten the top knobs (29) securely, by
turning them clockwise and the bottom knobs (29), by turning it clockwise, Fig.5.
Assemble the side supports
Bring the side support (35) up to the main structure, position it on the holding pins.
Next, use the Allen wrench (26) to tighten the screws (74) and washers (101)
To the foot rest. Perform the same assembly operation with the other foot rest
Fig.6.
Fig.5 Fig.6
Assemble the handrails.
First, take the combination box wrench (28) and loosen screw, located on the
base of the handrail (9 and 10), a few turns in an counter-clockwise direction.
Rotate the handrails (9 and 10) in the direction of the arrows.
Once the handrails are positioned, use the box wrench (28) to retighten screws
securely Fig.7.
ATTENTION: Cylinder (21) is packed under high pressure so it must not be
knocked. If it is knocked this may damage it and impair the operation of the
treadmill Fig.8.
Fig.7 Fig.8
13
ASSEMBLY INSTRUCTIONS (cont’d)

STORAGE
Caution: You must be able to safely lift 20 kg (45lbs) in order to raise\lower and move the treadmill.
To protect the floor or carpet from damage, place a mat under the treadmill. Keep the out of directtreadmill
sunlight. Do not leave the treadmill in the storage position in temperatures above 85 degrees Fahrenheit.
Do not attempt to move the treadmill over uneven surface.
Fig.9 Fig.10
FOLDING YOUR UNIT.
IMPORTANT: Before folding your unit, make sure that the hand rails (9 and 10)
are fitted and tightened correctly. This treadmill is equipped with a safety release
mechanism for folding purposes. To fold and store the unit follow the instructions
below, Fig.9:
Before attempting to fold the unit, stop the belt, lower the elevation setting to
minimum and unplug the cable from the mains socket. Lift and fold the machine
up until you hear it lock into position (16), located at the bottom of the machine,
Store your unit in a dry place, preferably not subject to changes in temperature.
UNFOLDING YOUR UNIT.
If you wish to use the treadmill, reverse the above procedure. Use your foot to press
lever (16) in the direction of the arrow and slowly lower the treadmill belt down to
the floor. when folding or unfolding the treadmill make sure that there are no children
about or obstacles that might hinder the folding motion Fig.9.
MOVEMENT & STORAGE.
The unit is equipped with wheels (54) to make it easier to move. Make sure that
the mains cable is unplugged from the wall socket.
If you wish to move the treadmill, the first thing to do is to fold it up, place your
hands on so that the wheels (56)the handrails (9 & 10) and tilt the treadmill,
rest on the floor. To prevent accidents DO NOT move the treadmill across
uneven floors Fig.10, or place the unit on its side.
14
Never place the treadmill on its side. Doing so will impair the
safety release mechanism and could result in personal injury.

IMPORTANT SAFETY INFORMATION
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USING THIS TREADMILL
CAUTION: Before starting any exercise program, it is recommended that you consult your physician.
WARNING: Connect this unit to a properly grounded outlet only.
DANGER: To reduce the risk of electric shock, always unplug the treadmill from the electrical outlet immediately after
using and before cleaning.
Grounding Instructions
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the
risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. See diagram below for grounding
methods.
1.The use of an extension cord with this product is not recommended. If an extension cord is needed, use a short (less than 10 feet) heavy gauge
(14 gauge or better) extension cord with a three prong (grounded) plug and receptacle.
2. Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped, damaged, or exposed to water.
3. Do not pull the treadmill by the power supply cord or use cord as a handle. Keep cord away from heated surfaces and open flames.
4. Fitness equipment must always be installed and used on a flat surface. Do not use outdoors or near water.
5. Do not insert any objects into any openings.
6.Use the treadmill only for it’s intended use as described in this manual. Do not use any attachments that are not recommend by the manufacturer.
7.Start your program slowly and very gradually increase your speed and distance.
8. Care must be taken when lifting or moving the equipment, so as not to injure your back. Always use proper lifting techniques
INSTALLATION
Installation Warnings
15
GROUNDING METHODS
GROUNDED
GROUNDING PIN

INSTALLATION (cont’d)
1.- Set switch (L), located on the
casing, to the “0”(OFF) position Fig.B.
2.- Press the circuit button (C) to reset
the unit.
3.- Next, set switch (L) to the “I”(ON)
position and the unit will be ready for
use again.
Should the circuit breaker trip
repeatedly then the most probable
causes are:
-Abnormal working conditions,
-Treadmill belt in need of lubricant,
-Solvent based lubricants used (use
BH type),
- Belt is too tight.
Plug the unit into a wall socket with an
EARTH terminal. Set switch (L) to
Position [1].
Fig.B
OPERATING INSTRUCTIONS.-
FITNESS.
Being fit means living life to the full.
Modern society suffers greatly from
stress. City life is basically sedentary.
There are too many calories and too
much fat in our diet. All doctors agree
that regular exercise is a good way to
Control our weight, make us more fit
and help us to relax.
ADVANTAGES OF EXERCISE.-
Regular exercise below a certain level
for 15/20 minutes becomes aerobic.
Aerobic exercise is basically exercise
that uses oxygen. Normally, this is a
continuous exercise without pauses.
In addition to sugars and fats, the
body also needs oxygen. Regular
exercise improves the body’s ability to
supply oxygen to all of the muscles
and at the same time improve lung
function, the heart’s pumping capacity
and better blood circulation. In short,
the energy produced during exercise
burns kilocalories (known as calories).
EXERCISE & WEIGHT
CONTROL.-
The food we eat is transformed into,
among other things, energy (calories)
for our body. If we take in more calories
than we burn then the result is an
increase in weight and vice versa, if we
burn more calories than we eat, we lose
weight. When resting the body burns
around 70 calories per hour to keep our
vital functions active. The table shows
approximate energy use for an average
person doing various activities.
ACTIVITY CALORIES
USED PER
HOUR
Walking, moderate
pace
140
Housework 150
Swimming (400 m/h) 300
Dancing 350
Walking, brisk (6 km/h) 370
Tennis 420
Cycling (30 km/h) 500
Squash 690
EXERCISE PROGRAM.-
Before starting any exercise program,
Bearing in mind that exercise programs
vary depending on age and physical
condition, it is advisable to consult your
doctor given that you will achieve better
results based on his/her advice or
suggestions. Regardless of whether
16
Your goal is to become more fit, control

your weight or for physiotherapy, always
remember that your exercise should be
gradual, planned, varied and not too
demanding. We recommend that you
should exercise 3 to 5 times per week.
Before beginning a session it is
important to do a warm-up for 2-3
minutes at low speed. This will help
protect your muscles and prepare your
cardiorespiratory system.
The next stage will last 15-20 minutes at
a pulse rate of between 65 to 75%, or
between 75 to 85% for those already
accustomed to exercise. At a later
can divide this time between both levels
but always remembering that the pulse
rate must not exceed 85% (aerobic
area) and never reach the maximum
heart rate limit that corresponds to our
age.
We you have finished, it is important to
relax the muscles. This can be done by
walking at a low speed for 2-3 minutes
until the heart rate drops below the 65%
line. This will prevent muscle pain,
especially after an intense session. It is
also advisable to finish the program with
some relaxation exercises on the floor.
FINAL NOTE.
We hope that you enjoy your unit. You
will soon notice the benefits of your
controlled exercise program, you will
feel better, have more energy and
suffer less stress. You will see for
yourself that it is worth staying in
shape with BH.
INSPECTION & MAINTENANCE.-
Switch the unit off and unplug the
mains cable. Use a damp cloth or
to clean thetowel dust off the treadmill,
especially the
side bars and the electronic console.
Do not use solvents.
Use a vacuum cleaner to carefully
vacuum around the visible components
(belt, structure, etc.). You can also
vacuum the underside of the unit by
resting it on one of its sides.
ATTENTION:
Periodically check that all of the
fastening elements are duly tightened
and connected correctly.
Check and tighten all the parts on your
unit every three months.
Use of this machine with worn parts,
e.g. the drive belt, running belt or
rollers, may cause the user injury.
When in doubt about any parts on the
machine, do not hesitate to get in
touch with the Technical Assistance
Service by phoning customer services
(see last page in manual).
We recommend that your use original
spare parts to replace any worn
components. The use of other spare
parts may cause injuries or affect the
performance of the machine.
BH RESERVES THE RIGHT TO
MODIFY THE SPECIFICATIONS OF
ITS PRODUCTS WITHOUT PRIOR
NOTICE.
17
stage, once we become more fit, we
INSTALLATION (cont’d)

Treadmill Operations
ELEMENTS OF THE MONITOR
A: This display gives a simultaneous
readout of SPEED; INCL.; TIME; DIS.;
and CAL..
Matrix red dot window.
B: Incline function quick buttons (3-6-
9-12).
Speed function quick buttons (2-5-7-
10)
C: The electronic monitor has 29 push
buttons;INCLINE (▲▼ ); START;
PROGRAM; MODE; SPEED Km/h
(▲▼ ); STOP.Quick speed buttons;
Quick incline buttons; fan button;.12
quick program buttons.
E: Slot for safety key.
F: Safety key.
STARTING
Plug the unit into a wall socket with an
EARTH ground and set switch (L) to
position (1).
The safety key must be inserted into
its spot , otherwise the machine will
not operate. As soon as the safety key
is in place, the machine will beep,
indicating that the machine is READY
to be used.
CHANGING FROM
KILOMETERS TO MILES
This machine has the option to display
speed in km/h or mph. The factory
setting for the machine is mph.
To change from mph to km/h follow
these steps:
Unplug the machine from the mains
supply, remove the safety key. Plug
the machine back in and insert the
safety key into its slot.
Press and hold the INCLINE▲and
SPEED▲keys at the same time for 5
approximately seconds. The speed
display will show the number 1.0, the
said number corresponds to km/h per
hour.
OPERATING INSTRUCTIONS
MANUAL MODE
Pressing the START key, the machine
will start within 3 seconds, shown by a
countdown 3-2-1, at a speed of
0.6mph.
You can increase or decrease the
speed setting in MANUAL mode by
pressing the SPEED▼▲ keys,
between 0.6–11 mph, you can also
increase or decrease the speed
setting by pressing the quick access
keys, the said keys correspond to
values of 2–5–7–10 mph.
By pressing the inclination keys
INCLINE▼▲ you can adjust the
elevation level, for values between 0-12.
There are also level function quick
access key, whose values correspond
to 3–6–9–12.
The machine will stop if you press the
STOP key or if you remove the
SAFETY KEY
18