Blaupunkt TravelPilot DX-V User manual

TravelPilot Navigation
TravelPilot DX-V
Installation instructions
http://www.blaupunkt.com

2
Safety precautions
Congratulations on your purchase of this Blaupunkt product. Thank you for the trust you are putting into our brand!
The following installation instructions are intended to help you getting the best performance from your Blaupunkt product. To avoid the
aggravation of costly mistakes and serious damage to your system, please read all of the instructions carefully before you begin. If
you’re not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician.
Installation and connection regulations
While connecting and installing this equipment, make sure to disconnect the negative terminal of the battery.
Important!
Observe all safety precautions provided by the automobile manufacturer (alarm systems, immobilisers, airbag)!
Before drilling the holes for mounting and wiring, make sure that no existing wiring or vehicle parts will be damaged
(e.g. petrol tank, petrol lines).
Use wire bushings for all sharp-edged holes.
To avoid interference, make sure to lay the wiring far enough away from the wire harness.
Attach a fuse to the positive supply wire at a maximum of 30 cm from the battery to protect the battery and the positive
supply wire in the event of a short circuit.
The navigation equipment is suitable for vehicles with:
•12 V battery power
•Negative pole on the vehicle body

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 3
Contents
Installing the control unit ...6
Important installation
information for the
speedometer signal ............6
Connecting the speedometer
signal.................................................... 7
Connecting the back-up
lights signal wire .................7
Video input assignment......7
System test
after installation ..................8
Calibration ...........................8
Calibrating the Gala curve................. 8
Technical data .....................9
Basic navigation unit ......................... 9
Safety precautions ..............2
Installation ...........................4
Description ..........................................4
Notes on how the system functions ... 4
Installation preparations.................... 4
Installing
the navigation unit ..............5
Where to install the navigation unit .... 5
Positive connection............................ 5
Negative connection .......................... 5
Installing the GPS antenna ..5
Installing the display...........6
Safety instructions ............................. 6
Installing the display .......................... 6
Uninstalling the display ..................... 6
What’s included
in the delivery ....................10
Assembly illustrations..... 13
Connection diagrams .......14
DX-V and RC 09H
in the front .........................................15
DX-V in the car boot,
TMC tuner box and
RC 09H in the front ...........................16
DX-V, TMC tuner box and
RC 09H in the front ...........................17
DX-V connection to
terminal area A.................................. 18

4
Installation
Description
The TravelPilot DX-V navigation system is an independent sys-
tem with an integrated gyroscope. After a destination has been
entered and activated, the system delivers visual driving recom-
mendations as pictograms on a colour monitor and spoken driv-
ing information via a separate speaker well in advance of any
turns or changes in driving direction required. In this way, the
system guides the motorist from his/her starting point on the best
route to the selected destination.
All of the available functions are described in the specifications
of the CD-ROM used.
Notes on how the system functions
The TravelPilot is equipped with an automatic calibration
feature which is required to determine the current vehicle
position. Depending on the GPS reception available, the
calibration is completed after the vehicle has been driven
approx. 15 km. Driving along a winding route (in the city),
which is indicated on the monitor on a map, accelerates the
calibration.
The speedometer signal connection in the vehicle allows the
system to determine the distance driven. If there is no speed-
ometer signal, it will be necessary to have a route sensor in-
stalled by an authorised customer service centre.
In this case, you will have to order a sensor kit (route sen-
sor, magnet strips, bracket, plug and installation instruc-
tions) from your dealer.
Order No.: 7 607 611 093
Installation preparations
Before starting the installation, check to see that
no parts from the installation pack are missing......... page 10
The following steps must be completed to install the equipment:
•Installing the navigation unit (computer).......... page 5
•Installing the GPS antenna ................................. page 5
•Installing the display (monitor) .......................... page 6
•Installing the operating unit ............................... page 6
•Installing the speedometer signal wire ............. page 6
•Installing the back-up lights signal wire ........... page 7

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 5
Installation
Installing the navigation unit
Where to install the navigation unit
Important!
Before inserting the TravelPilot DX-V, you have to make sure
that the gyroscope is positioned horizontally (see Fig. 5,
page 14).
The TravelPilot DX-V can be installed in the car radio compart-
ment in the vehicle (installation depth 218 mm). You will need
an installation bracket (order no. 8 601 310 555) (see Fig. 1 page
13).
For vehicles without a DIN compartment, a universal equipment
housing has been included (see Fig. 1.1 page 13). Check to see
which method of installation is required for the vehicle and, if
necessary, use a vehicle-specific installation kit.
When selecting an installation location, you must remember that
the navigation unit has to be built into the vehicle body.
Installation position:
right / left min. -5˚/ max. +5˚
slope to the rear min. -3˚/max. +100˚
A fan has been built into the back of the unit to cool it when
it overheats. To allow for sufficient air circulation, make sure
that the air vents are not blocked. Use only the hole strips
to attach the unit to the mounting bolt.
Make sure that there is enough room to insert and remove the
navigation CD.
Positive connection
Connect the navigation unit to continuous plus and the positive
connection to the ignition.
Lay the continuous plus wire (red) to the battery (do not lay the
wire directly along any wire harnesses). Connect a fuse holder
to protect the positive wire at a maximum of 30 cm from the
vehicle battery (if necessary, drill a hole in the splashback and
use the necessary wire bushing).
Connect the switching plus wire (black) to terminal 15 on
the fuse holder (plus is switched by the ignition) behind the
fuse.
Negative connection
Screw the negative wire (brown) directly to the vehicle body.
Scratch the contact points on the ground down to the metal and
grease it with graphite grease (important for a good ground).
Installing the GPS antenna
Install the antenna according to the enclosed instructions.
If the GPS antenna is installed inside the vehicle, there is no
guarantee that the system will function properly.

6
Installation
Installing the display
Safety instructions
The display support must never be greased or lubricated
with oil.
The monitor cable must be laid so that it is not subjected
to any tensile strains or other loads.
Important!
Do not mount the monitor within the inflation range of
the airbags (on the driver’s side, the passenger side or
the side airbags) or where it might strike the head or knees
of anyone in the vehicle in the event of an accident!
Before drilling the holes for the mounting screws and
wiring, make sure that no damage will be done to cov-
ered wiring, the petrol tank or fuel lines!
Installing the display
1. Attach the display support to the display (Fig. 2, Page 13).
Mount the display together with its support onto the dash-
board or console (Fig. 3, Page 13).
Connect the cables and run them towards the navigation unit.
Uninstalling the display
1. Press the tab on the plug and carefully pull out the plug (do
not pull on the cable) (Fig. 4, Page 13).
2. Push together the lugs on the display support and pull out
the display in an upwards direction (Fig. 4, Page 13).
Installing the control unit
Mount the control unit bracket in a location where the control
unit will be easily accessible, e.g. on the centre console.
Important!
Do not mount the control unit within the inflation range of the
airbags (on the driver’s side, the passenger side or the side air-
bags) or where it might strike the head or knees of anyone in the
vehicle in the event of an accident!
Before drilling the holes for the mounting screws, make sure that
no damage will be done to covered wiring, the petrol tank or fuel
lines!
Make sure that the vehicle operating elements remain easily
accessible and are not obstructed in any way (gear stick, hand
brake, etc.)!
Note:
The “wide screen”monitor is equipped with an integrated
infrared receiver. This means that the supplied receiver for
the RC 09H does not necessarily have to be installed.
Important installation information for
the speedometer signal
When connecting the speedometer signal, make sure to
observe the following information:
1. Where to find the signal: For many vehicles, the speedom-
eter signal can be found in the vehicle-specific car radio plug.
Contact the customer service of the vehicle manufacturer or
an authorised navigation dealer to find out what the exact pin
allocation is.

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 7
2. Do not use the speedometer signal from ABS control units or
control circuits.
3. Important:
We assume no responsibility for any equipment that is in-
stalled incorrectly and the consequences thereof!
Connecting the speedometer signal
Important:
Thisconnectionshould be made by an authorised customer serv-
ice centre.
The connection is made with the speedometer signal wire
(8 618 841 988) to the vehicle-specific speedometer signal con-
nection. (see connection diagram, page 18).
Connecting the back-up lights signal
wire
Important:
Thisconnectionshould be made by an authorised customer serv-
ice centre.
The connection is made with the back-up lights signal wire
(8 618 842 033) to the vehicle back-up lights. Make sure that
there are +12V at the connection when the vehicle is backing up
(see connection diagram, page 18).
Important:
We assume no responsibility for any equipment that is installed
incorrectly and the consequences thereof!
Installation
Video input assignment
The video input socket is intended for future applications. For
information on connection options, please contact a Blaupunkt
dealer or our hotline. See connection diagram for assignment.
Description Input /
Ouput CommentPin
EXT_R E
Low = PAL Format / High = NTSC Format
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
EXT_G
EXT_B
V_GND
EXT_SYNC
NC
U14
STANDARD SWITCH
EARTH
NC
N. B.
Switch on EXT.
UB
Screen switch
MP_U53
Low = Off / High = On
E
E
E
E
-
A
E
A
E
A
A
A
Low = Mirror image / High = Normal image
Red input
Green input
Blue input
Synchronisation input
Video earth
1
15
10

8
Installation
System test after installation
The system test allows you to test the external connections to
see that they are working correctly.
Proceed as follows:
1. Turn off TravelPilot DX-V
2. Press the button and keep it pressed.
3. Turnon the TravelPilot DX-V andrelease the button when
the service menu appears.
4. Using the button, select the test menu and press the
OK
button.
5. Now select the required test using the or button, press
the
OK
button and follow the on-screen instructions.
If the test was completed successfully, the menu item will be
labelled with a tick. If an error occurs, an appropriate notice
will be displayed.
6. Close the service menu by pressing the button.
Calibration
After installation, the TravelPilot DX-V must be calibrated. You
will find the procedure for this described in the operating instruc-
tions.
Calibrating the Gala curve
After the TravelPilot DX-V is calibrated, the values that were
determined must be transferred to the control unit software so
that the Gala feature (sound-dependent volume adjustment)
works correctly.
Please proceed as follows:
1. Turn off TravelPilot DX-V.
2. Press the button and keep it pressed.
3. Turnon the TravelPilot DX-V andrelease the button when
the service menu appears.
4. Using the button, select the settings menu and press
the
OK
button. This procedure transfers the calibration val-
ues that were previously determined to the control unit.
5. Close the service menu by pressing the button.

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 9
Technical data
Basic navigation unit
Rated voltage (Urat) 14 V / DC
Rated current (I) Typically 0.55 A (Imax 1.05 A)
Stand-by current Typically 0.35 A
Speech output /
volume Max. 3 Watt/4 Ohm
Time to first position
computation (Warm start, memory refresh)
< 2 minutes; (cold start, memory
clear) < 15 minutes
CD-ROM drive For 12 cm CD to DIN EN 60908
only
Operating temperature -15°C to +60°C
Mounting orientation right / left
min. - 5˚ / max. + 5˚
slope to the rear
min. - 3˚ / max. +100˚
Width 187.5 mm
Height 58.5 mm
Depth 174.4 mm
Weight 1.35 kg
Subject to modification!

10
TravelPilot DX-V
7 612 001 078
Navigation unit with integrated gyroscope and GPS receiver
7 612 001 073/74
depending on the model
7 612 001 071/72
depending on the model
8 672 000 013
GPS-antenna
8 601 360 105
Operating unit incl. bracket and IR sensor (eye):
8 618 841 412
6 m of DC wire
What’s included in the delivery

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 11
8 618 842 033
4.5 m of back-up lights signal wire
8 604 492 627
Monitor cable
(The cable is only included in the scope of delivery when com-
bined with the 7 612 001 071/072 monitor.)
8 618 841 988
4 m of speedometer wire
8 604 492 513
0.3 m of connection wire (compartment C1)
8 604 492 514
0.3 m of connection wire (compartment A)
What’s included in the delivery
blue
yellow white
brown

12
8 606 590 212
Universal equipment housing
8 604 492 522
Tuner box / RC 09H connection wire
8 604 492 573
Y-adapter
What’s included in the delivery

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 13
Assembly illustrations
Fig. 1
8 601 310 555
Fig. 1.1 Fig. 2
Fig. 3
Fig. 4
2.
1.

14
–5°
+100
Assembly illustrations
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
C
B
A
14710 13 16 19
36912 15 18
258
11 14 17 20
C-1 C-2 C-3
2
D
13
4
5
6
7
8
9
10
AB
1Gala/Tacho 1 –
2–2–
3RFLS 3 –
4Permanent +12V 4 –
5–5Speaker out LF+
6 Illumination 6 Speaker out LF-
7 Ignition 7 –
8Ground 8 –
D
1 GND
2 Data Out
3 Data In
4 Mute (AR)
5—
6—
7 Line GND
8—
9 Line Out
10 —
o.k.
Fig. 5
–10°
+100
C
C1 C2 C3
1 Wheel sensor 7 CAN High 13 –
2 Wheel sensor 8 CAN Low 14 –
3 FB GND 9 +12V Permanent 15 –
4-10 +12V switched (RC 09) 16 –
5-11 PPM (RC 09) 17 –
6-12 PPM-GND 18 –
19 –
20 –
–5°
+100
90˚
90˚
Connection diagrams

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 15
Connection diagrams
TravelPilot DX-V
Video-IN
GPS-antenna
Wheel sensor
TMC car radio connection
(Accessory cable
Skyline II: 7 607 612 093;
Funline II: 7 607 613 093) not connected
A
IR remote control
RC 09H
to the monitor
Installation location: DX-V and RC 09H in the front (DIN compartment)

16
Connection diagrams
A
5A
+ 12V
8 604 492 522
Tuner box / RC 09H connection wire
Attach the ground cable using
the torx-head screw provided
8 604 492 540 Tuner box
TravelPilot DX-V
8 604 492 533
8 604 492 534
Antenna
Radio
8 604 492 523
IR remote control
RC 09H
to the monitor
Y-adapter
8 604 492 573
Installation location: DX-V in the car boot
TMC tuner box and RC 09H in the front (DIN compartment)

Anhang
Allgemeines Kurzanlei- TourenZieleingabe Zielspeicher Einstellun- 17
Connection diagrams
Attach the ground cable using
the torx-head screw provided
8 604 492 540 Tunerbox
TravelPilot DX-V
8 604 492 533
8 604 492 534
Antenna
Radio
8 604 492 523
IR remote control
RC 09H
to the monitor
A
5A
+ 12V
Y-adapter
8 604 492 573
Installation location: DX-V, TMC tuner box and RC 09H in the front (DIN compartment)

18
Connection diagrams
12V
Kl.30
A
TravelPilot DX-V
GPS-antenna
RFLS
Back-up lights
signal = +12 V
black
red
Speedometer
signal
Earth
Illumination
DX-V connection to terminal area A

Country: Phone: Fax: www:
Germany (D) 0180-5000225 05121-49 4002 http://www.blaupunkt.com
Austria (A) 01-610 390 01-610 393 91
Belgium (B) 02-525 5454 02-525 5263
Denmark (DK) 44 898 360 44-898 644
Finland (FIN) 09-435 991 09-435 99236
France (F) 01-4010 7007 01-4010 7320
Great Britain (GB) 01-89583 8880 01-89583 8394
Greece (GR) 0030-210 94 27 337 0030-210 94 12 711
Ireland (IRL) 01-4149400 01-4598830
Italy (I) 02-369 62331 02-369 62464
Luxembourg (L) 40 4078 40 2085
Netherlands (NL) 023-565 6348 023-565 6331
Norway (N) 66-817 000 66-817 157
Portugal (P) 01-2185 00144 01-2185 11111
Spain (E) 902-120234 916-467952
Sweden (S) 08-7501500 08-7501810
Switzerland (CH) 01-8471644 01-8471650
Czech. Rep. (CZ) 02-6130 0441 02-6130 0514
Hungary (H) 01-333 9575 01-324 8756
Poland (PL) 0800-118922 022-8771260
Turkey (TR) 0212-3350677 0212-3460040
Blaupunkt GmbH
01/ 2004 CM/PSS 8 622 402 694 B(GB)