Blaupunkt TravelPilot Lucca 3.5 User manual

Mobile Navigation
TravelPilot Lucca 3.5
www.blaupunkt.com
Operating and installation instructions
(Long version)
Lucca3_5B_long_GB_NEU•.indd 1Lucca3_5B_long_GB_NEU•.indd 1 04.10.2007 16:49:06 Uhr04.10.2007 16:49:06 Uhr

2
Device overview
Device overview
5
86
7
9
3
124
10
11
Lucca3_5B_long_GB_NEU•.indd 2Lucca3_5B_long_GB_NEU•.indd 2 04.10.2007 16:49:16 Uhr04.10.2007 16:49:16 Uhr

Device overview
3
1VOL -: Decreases the volume
2On/Off switch:
Long press (longer than 3 seconds):
Switches the Lucca on or off.
Short press: Opens the main menu.
3VOL +: Increases the volume
4Display (Touchscreen): All entries and the
control of Lucca are carried out in a simple
and intuitive way by touching the buttons
shown on the display.
5TMC antenna input
6USB-port for use as card reader for the SD/
SDHC/MMC cards
7Headphone jack
8SD/SDHC/MMC card slot
9Socket for connecting the Lucca to the battery
charger or the charger cable for the cigarette
lighter.
:Light sensor
;Serial Port (for future expansions)
•
•
Lucca3_5B_long_GB_NEU•.indd 3Lucca3_5B_long_GB_NEU•.indd 3 04.10.2007 16:49:23 Uhr04.10.2007 16:49:23 Uhr

4
Contents
Device overview ..................................2
Safety notes ........................................6
Use as directed .....................................6
Safety notes for navigation......................6
Safety notes for handling the Lucca .........6
Notes for handling the CD/DVD................6
Disposal notes ......................................7
Initial startup of the Lucca....................7
Lucca scope of delivery..........................7
Protective screen film ............................7
Charging the battery..............................7
Switching on the Lucca ..........................8
Setting the language ..............................8
Installation in the vehicle .....................8
Attaching the suction cup holder .............8
Attaching the clamp ..............................8
Installing Lucca in the clamp ...................8
Removing the Lucca ..............................9
Removing the suction cup holder.............9
Switching on/off..................................9
Switch-on ............................................9
Switching off ........................................9
Reset...................................................9
Operating the menus .........................10
Main menu .........................................10
Keyboard ...........................................10
Intelligent auto-completion function....10
Error-tolerant entry ..........................10
Lists..................................................10
Buttons..............................................10
GPS info............................................11
GPS mode of operation ........................11
Displaying GPS info .............................11
Performing basic settings ..................12
Adjusting the time zone .......................12
Entering the home address ...................12
Activating the PIN query .......................12
Configuring the PIN query..................13
Locking/unlocking the Lucca..............13
Changing the PIN .............................13
Navigation ........................................14
General notes about the navigation ........14
Starting the navigation .........................14
Entering a destination address ..............14
Using the home address as destination...15
Copying the destination from
the favourites......................................15
Copying one of the last destinations.......16
Entering a point of interest....................16
Selecting a point of interest nearby,
in the destination area or at home.......16
Selecting a point of interest at
a specific location ............................17
Selecting a point of interest
on the map......................................17
Selecting a supraregional
point of interest ...............................18
Entering coordinates............................18
Copying a destination from the map .......19
Storing the position ...........................19
Managing destinations.......................20
Saving destinations .............................20
Storing a destination entered .............20
Saving one of the last destinations......20
Renaming a destination
(favourites only)..................................20
Deleting a destination ..........................20
Delete all destinations..........................21
Calculating a route.............................21
Demo................................................22
Starting the demo ...............................22
Demo settings.....................................22
Tour planning ....................................22
Planning a tour....................................22
Tour planning from favorites..................23
Start route guidance ............................23
Calculating a route...............................23
Lucca3_5B_long_GB_NEU•.indd 4Lucca3_5B_long_GB_NEU•.indd 4 04.10.2007 16:49:23 Uhr04.10.2007 16:49:23 Uhr

Contents
5
Save a tour .........................................23
Delete a tour.......................................23
Show in map.......................................23
Exiting the menu .................................23
Specifying route options ....................24
Route guidance..................................25
Start route guidance ............................25
Disturbed GPS reception......................25
Quitting the route guidance...................25
Reaching the place of destination ..........25
Working with the map ........................26
Showing a map ...................................26
Moving and scaling the map ..................26
Touching the map................................26
Buttons..............................................26
Performing map settings ......................26
Voice output during route guidance.....27
Map display during route guidance......28
Navigation tools ..................................28
Route information ...............................28
Speed limit.........................................28
Additional functions during
the route guidance.............................29
Entering a blocking ..............................29
Cancelling route guidance.....................29
Skipping the next destination................29
Display information about
the destination....................................29
Display route list .................................30
TMC function.....................................30
Connecting the TMC antenna ................30
Switch on automatic traffic jam detours ..30
Searching for TMC stations ...................31
Showing traffic reports ........................31
Multimedia........................................31
Inserting a memory card.......................31
Starting multimedia .............................31
Playing music files ...............................31
Additional functions .........................32
Browse...........................................32
Equalizer ........................................32
Showing image files.............................32
Slide show ......................................33
Additional functions .........................33
Browse...........................................33
Exiting multimedia...............................33
Removing the memory card ..................33
Data transfer.....................................34
Preparing the memory card ..................34
Using road maps from memory card.......34
Using media files from the memory card..34
Configuring Lucca..............................35
Device settings ...................................35
Display brightness............................35
Button sound...................................35
Language........................................35
Clock..............................................35
Saving energy..................................35
Theft protection...............................36
Factory settings ...............................36
Calibrating the touchscreen...............36
Product information .........................36
Demo mode ....................................36
Settings for navigation .........................36
Home address .................................36
Continuing a tour automatically ..........36
Selecting a dataset...........................37
POI note .........................................37
Voice instructions.............................37
Units ..............................................37
Software of the Lucca ........................37
Reinstalling navigation software ............37
Updating the navigation software...........37
Technical data ...................................38
Service .............................................38
Warranty...........................................38
Troubleshooting table ........................39
Lucca3_5B_long_GB_NEU•.indd 5Lucca3_5B_long_GB_NEU•.indd 5 04.10.2007 16:49:23 Uhr04.10.2007 16:49:23 Uhr

6
Safety notes
Safety notes
For your personal benefit, carefully read the fol-
lowing safety notes and warnings before operat-
ing your Lucca for the first time.
Use as directed
The device is designed for mobile use in vehicles.
Specialinformationaboutthe navigation of trucks,
busses and campers, such as altitude and width
limitations or maximum permissible road load, is
not included in the navigation data!
Navigation off the roads (offroad) is possible with
the Lucca.
Safety notes for navigation
Caution:
Do not operate the Lucca while driving to protect
yourself and others against accidents!
View the display only if you are in a safe travel situ-
ation!
The street routing and traffic signs have priority
over the instructions of the navigation system.
Follow the instruction of the Lucca only if circum-
stances and traffic regulations allow! Lucca will
bring you to your destination even if you have to
deviate from the planned route.
Notes:
Routes are best planned before starting
your trip. If you want to enter a new route
while on the road, head for the next park-
ing or rest area.
If you did not understand the voice infor-
mation or if you are not sure what to do at
the next intersection, use the map or arrow
display for quick orientation. Or you repeat
the voice instruction by touching the bot-
tom display bar in the map display.
•
•
Safety notes for handling the Lucca
Caution:
Protect the device against moisture since it is not
waterproof and not splashproof.
Do not modify or open the device.
Do not expose the device to extreme tempera-
tures (cold, heat, fire), e.g. in a parked car with
direct sun exposure, to avoid the formation of con-
densate inside the device or overheating.
Otherwise, the device or the battery could be de-
formed, ignite or explode.
Notes:
Remove the Lucca from the power supply
when you park your vehicle since the Lucca
continues to use battery power and could
deplete the vehicle battery.
Do not unplug the connector by pulling on
the wire. The wire could be damaged.
Do not use strong detergents for cleaning
the device. Use only a moistened, lint-free
cloth.
Notes for handling the CD/DVD
The device is supplied with a CD/DVD that con-
tains navigation software and map material. To
protect the CD/DVD against dirt and damage, ob-
serve the following notes:
Store the CD/DVD in its case.
Hold the CD/DVD only at the edge.
Do not expose the CD/DVD and the case
to direct sunlight.
Use only a clean CD/DVD. If necessary,
clean the CD/DVD with a soft, lint-free
cloth from inside to outside.
Never clean the CD/DVD in a circular mo-
tion.
Do not use any solvents, including on the
printed side of the CD/DVD.
•
•
•
Lucca3_5B_long_GB_NEU•.indd Sec6:6Lucca3_5B_long_GB_NEU•.indd Sec6:6 04.10.2007 16:49:23 Uhr04.10.2007 16:49:23 Uhr

Safety notes | Initial startup of the Lucca
7
Disposal notes
Do not dispose of your old unit in the house-
hold trash!
Use the return and collection systems available to
dispose of the old device.
Do not discard any batteries in the house-
hold trash; instead, return them to the cor-
responding collection sites.
Initial startup of the Lucca
Lucca scope of delivery
The scope of delivery contains the following com-
ponents:
Lucca
Suction cup holder with clamp
Battery charger
Charger cable for cigarette lighter
TMC line antenna
Operating instructions (short version)
Backup DVD
Note:
We recommend the use of original Blaupunkt
accessories.
Protective screen film
Prior to the initial use, carefully remove the pro-
tective film from the display.
Charging the battery
The built-in battery allows for operating the Luc-
ca battery-operated for up to 3 hours. The exact
usage time is dependent upon the type of opera-
tion.
The charge state indicator of the battery is located
in the top display bar. The number of dark block
segments on the battery symbol indicates the
charge state of the battery (0 to 3 segments). The
symbols have the following meaning:
The device is supplied by an external
power source.
The device is supplied by its internal
battery. The charge state of the battery is suf-
ficient.
The device is supplied by its internal
battery. The charge state of the battery is
low.
Notes:
Use only original chargers for operating
and charging the battery.
The battery is equipped with a protection
that prevents overheating. For this reason,
•
•
•
•
•
•
•
•
•
•
•
•
Lucca3_5B_long_GB_NEU•.indd 7Lucca3_5B_long_GB_NEU•.indd 7 04.10.2007 16:49:24 Uhr04.10.2007 16:49:24 Uhr

8
Initial startup of the Lucca | Installation in the vehicle
the battery is no longer charge at an ambi-
ent temperature above 45 °C.
Switching on the Lucca
The On/Off switch is used to switch the Lucca on
and off. In its delivery state, the Lucca is switched
off.
Note:
Upon purchasing the Lucca, the battery may-
be empty. Please charge the battery before
using the device.
A
A
Press and hold the On/Off switch for longer
than 3 seconds.
Setting the language
The Lucca uses English as the standard language
for the menus and voice output. When you switch
on the Lucca for the first time, a dialogue menu ap-
pears in which you can select another language:
Select your preferred language in the dia-
logue menu.
Please follow the instructions.
The language is loaded and the main menu is
displayed.
쏅
쏅
쏅
Installation in the vehicle
For temporary installation in a vehicle, the Lucca
features a suction cup holder with a suction cup to
attach it to the windshield.
Caution:
Install the Lucca so that it does not block your view
and does not distract from the traffic.
Do not install the Lucca in the airbag deployment
area.
Ensure that the Lucca does not pose a threat to
passengers in the vehicle in case of emergency
braking.
Attaching the suction cup holder
The Lucca can be installed in the vehicle in a sim-
ple way using the holder.
Locate a suitable place for installing the Luc-
ca.
To ensure a perfect hold, the glass must be
free of dust and oil. If necessary, clean the
glass first using a lens cleaning tissue.
Press the suction cup of the holder against
the windshield.
Push the lever on the support towards the
glass.
The holder can now be adjusted. The track
for mounting the Lucca must be aligned ver-
tically.
Attaching the clamp
The suction cup holder features a mount for the
holder.
Engage the clamp downward with the suction
cup holder.
Installing Lucca in the clamp
The Lucca features 2 cut-outs at the top and bot-
tom side for the clamp.
First, insert the Lucca in the clamp at the top
side and then engage it in the bottom.
쏅
쏅
쏅
쏅
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd 8Lucca3_5B_long_GB_NEU•.indd 8 04.10.2007 16:49:24 Uhr04.10.2007 16:49:24 Uhr

Installation in the vehicle | Switching on/off
9
Removing the Lucca
Hold the Lucca in both hands and press
against the clamp with your thumbs.
Pull the Lucca up and out of the clamp.
Removing the suction cup holder
If you change vehicles, you can simply remove the
support.
Push the lever on the support away from the
glass.
Carefully loosen the suction cup at the edge
from the glass so that air can enter between
suction cup and glass.
Carefully pull the suction cup off of the glass.
쏅
쏅
쏅
쏅
쏅
Switching on/off
The On/Off switch is used to switch the Lucca on
and off and to open the main menu.
Switch-on
Press and hold the On/Off switch for longer
than 3 seconds.
Switching off
Press and hold the On/Off switch for longer
than 3 seconds.
The Lucca is first placed in idle state and re-
mains ready for operation. All functions will
be completely switched off after 20 minutes.
Note:
The Lucca continues to use a small amount of
energy even if it is switched off. If you use the
Lucca again after an extended period of time,
it may be necessary to recharge the battery.
Reset
If the Lucca does not work properly, a simple reset
may help.
Press and hold the On/Off switch for longer
than 14 seconds.
The Lucca is switched off.
Press and hold the On/Off switch for longer
than 3 seconds.
The Lucca is restarted.
쏅
쏅
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd 9Lucca3_5B_long_GB_NEU•.indd 9 04.10.2007 16:49:28 Uhr04.10.2007 16:49:28 Uhr

10
Operating the menus
Operating the menus
Main menu
The main menu provides access to all applications
of the Lucca, to navigation, multimedia (Music
Player and Picture Viewer) and the settings.
Briefly press the On/Off switch to reach the
main menu from any other menu.
Keyboard
If text entries are required (e.g. for the destination
entry), a virtual keyboard appears on the display.
You can perform all entries using your finger. Only
capital letters can be entered.
This keyboard includes these keys:
Delete last character
Call up error-tolerant entry
Entering blank spaces
Call up alternate character keyboard (incl.
special characters, umlauts)
Call up numeric keypad, e.g. to enter the
house number
Call up character keyboard
Intelligent auto-completion function
During the entry, the Lucca auto-completes char-
acters as far as possible and offers only those
characters on the keyboard that are logically pos-
sible.
Error-tolerant entry
For city names, you can call up the error-tolerant
entry if the exact spelling is not known:
Touch the symbol in the text entry.
The error-tolerant entry is displayed.
Enter a city name and touch OK.
A list with alternate city names is displayed.
쏅
쏅
쏅
Lists
You can frequently display lists form which you can
select an entry (e.g. a destination). For example, if
you do not enter the complete name of a location,
a list with possible results is displayed.
To display a list with additional matching entries,
touch the List button. Longer lists require a longer
loading time.
Touch one of the buttons to
scroll through the list.
Touch an entry directly to accept it.
Additional buttons in lists:
Expand: Since the area of the display is lim-
ited, long entries are abbreviated. Touch this
button to display the complete entry.
Buttons
These buttons are located on many menus of the
Lucca:
Touch this button to return to the pre-
vious menu.
Touch this button to change to the
next page in the menu.
Touch this button to obtain access to
additional functions.
쏅
쏅
•
•
•
•
Lucca3_5B_long_GB_NEU•.indd 10Lucca3_5B_long_GB_NEU•.indd 10 04.10.2007 16:49:28 Uhr04.10.2007 16:49:28 Uhr

GPS info
11
GPS info
The GPS Info menu contains information about
your current position and your current speed. In
addition, you can view the strength of the GPS
signals.
GPS mode of operation
GPS is based on a total of 24 satellites that are
orbiting the earth and sending out signals. The
Lucca receives these signals and calculates its
distance to the individual satellites from the delay
times. It uses this information to derive its cur-
rent geographic position and compares it with the
map material. The supplied map material contains
the geographic coordinates of points of interest,
streets and cities that you can view on the dis-
play of the Lucca. Hence, the Lucca calculates the
route to the destination you entered by using the
information from the GPS satellites and the map
material.
The positioning requires signals from at least 3
satellites. Starting with the fourth one, it is possi-
ble to also determine height above mean sea level.
The positioning is carried out with an accuracy to
3 metres. Since the positioning and position dis-
play is carried out once every second, you can
view your movement on the map – even without
active route guidance.
Displaying GPS info
Touch the symbol in the main menu
of the Lucca.
The map is displayed.
Touch the symbol.
The Navigation menu is displayed.
Touch the button.
The display shows the second page
of the menu.
Touch the symbol.
The GPS Info menu is displayed.
쏅
쏅
쏅
쏅
This menu contains this information:
Latitude/Longitude: Current position in
east longitude and north latitude
Height: Current height above mean sea
level
Speed: Indicates the current speed of the
vehicle
Heading: Driving direction (reliable infor-
mation after approx. 5 km/h)
GPS Signal Quality: Signal strength of
the visible GPS satellites. The navigation
requires signals from at least four satel-
lites.
Note:
Heavily metal-evaporated windshields may
present an obstacle to the GPS reception of
the Lucca. If the GPS reception is insufficient
for the navigation, you may attempt to install
the Lucca at a different location in the vehicle.
For this purpose, please read chapter "Route
guidance", "Disturbed GPS reception".
–
–
–
–
–
Lucca3_5B_long_GB_NEU•.indd 11Lucca3_5B_long_GB_NEU•.indd 11 04.10.2007 16:49:28 Uhr04.10.2007 16:49:28 Uhr

12
Performing basic settings
Performing basic settings
Before starting a route guidance, perform these
basic settings:
Set the time zone of your position so that the
correct arrival times are displayed during the
navigation.
You should enter your home address to quick-
ly navigate home from any location.
Activate the PIN query to lock out unauthor-
ised persons from using the Lucca.
Adjusting the time zone
Touch the symbol in the main menu
of the Lucca.
The Settings menu is displayed.
Touch the symbol.
The Clock menu is displayed.
Touch the symbol.
A list with available time zones is
displayed.
Touch the time zone in the list that applies to
your current location.
Note:
The selection is facilitated by the display
of the capitols in the respective time zone.
"GMT" stands for Greenwich Mean Time, the
mean solar time at the Greenwich meridian
without considering daylight savings time.
Touch the symbol to activate (check
mark) or deactivate (no check mark)
daylight savings time.
Note:
If the time is changed at your position or if
you drive into a different time zone, you must
adjust the corresponding settings.
•
•
•
쏅
쏅
쏅
쏅
쏅
Touch the symbol to switch between
24-hour display (check mark) and
12-hour display (no check mark).
Touch the button to exit the menu
again.
Entering the home address
Touch the symbol in the main menu
of the Lucca.
The map is displayed.
Touch the symbol.
The Navigation menu is displayed.
Touch the symbol.
The Settings menu is displayed.
Touch the symbol.
The Destination Input menu is dis-
played.
Enter the address as described in the chapter
"Entering a destination address".
Touch the OK button.
The home address is saved.
Activating the PIN query
The PIN query allows you to lock out unauthorised
persons from using the Lucca. Hence, every time
you switch on the Lucca, the PIN (Personal Identi-
ty Code) you configured for yourself is requested.
The PIN can be changed at any time. If you should
forget the PIN, you can unblock the Lucca again
with the PUK (Personal Unblocking Key) which
you define yourself. The PUK cannot be changed.
Note:
During the PIN entry, you have only 3 attempts
to enter the correct PIN or subsequently 3 at-
tempts to enter the correct PUK. If you enter
an incorrect PUK for the 3rd time, your device
is permanently blocked and the Lucca must
be returned via the Blaupunkt service.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd 12Lucca3_5B_long_GB_NEU•.indd 12 04.10.2007 16:49:29 Uhr04.10.2007 16:49:29 Uhr

Performing basic settings
13
Configuring the PIN query
Touch the symbol in the main menu
of the Lucca.
The Settings menu is displayed.
Touch the symbol.
The Anti-Theft Protection menu is
displayed.
Touch the symbol.
The Anti-Theft PIN menu is dis-
played.
Follow the instructions and enter a self-se-
lected PIN.
Touch the OK button.
The initial configuration of the PIN is followed by a
request to enter a PUK. The PUK is used to unlock
the Lucca if you should forget the PIN.
Follow the instructions and enter a self-se-
lected PUK.
Touch the OK button.
To secure your PUK:
Register under http://puk.blaupunkt.com
and follow the instructions.
Locking/unlocking the Lucca
Prerequisite:
You configured the PIN query.
In the Anti-Theft Protection menu,
touch the symbol.
Note:
The symbol indicates the status (locked/un-
locked).
A PIN query is displayed.
Enter the PIN to lock or unlock the Lucca.
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
•
쏅
쏅
Changing the PIN
In the Anti-Theft Protection menu,
touch the symbol.
The Anti-Theft PIN menu is dis-
played.
Follow the instructions and enter a new self-
selected PIN.
Touch the OK button.
쏅
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd Abs1:13Lucca3_5B_long_GB_NEU•.indd Abs1:13 04.10.2007 16:49:29 Uhr04.10.2007 16:49:29 Uhr

14
Navigation
Navigation
General notes about the navigation
Caution:
Do not operate the Lucca while driving to protect
yourself and others against accidents!
View the display only if you are in a safe travel situ-
ation!
The street routing and traffic signs have priority
over the instructions of the navigation system.
Follow the instruction of the Lucca only if circum-
stances and traffic regulations allow! Lucca will
bring you to your destination even if you have to
deviate from the planned route.
Note:
To be able to extensively use the navigation of
the Lucca, perform the basic settings before
the first navigation (ch. "Performing basic set-
tings").
Starting the navigation
Note:
You can only select places of destination
(countries, cities, streets, house numbers)
that are contained in the map material.
Touch the symbol in the main menu
of the Lucca.
The map is displayed.
쏅
From the map, you can directly change to the
navigation menu or the Map Settings menu.
Touch the symbol.
The Navigation menu is displayed.
Touch the symbol.
The Map Settings menu is displayed.
Entering a destination address
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the symbol.
The Destination menu is displayed.
Enter the destination address in succession:
Note:
You donothavetorepeatenteringthecountry,
city and street information every time. Only if
your destination is at a different location than
the previous one will you have to re-enter the
destination address.
Touch the symbol and enter the
country.
쏅
쏅
쏅
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd 14Lucca3_5B_long_GB_NEU•.indd 14 04.10.2007 16:49:30 Uhr04.10.2007 16:49:30 Uhr

Navigation
15
Touch the symbol and enter the city
or postal code.
Touch the symbol and enter the part
of town.
- or -
Touch the symbol and enter the
street.
Touch the symbol and enter the
house number.
- or -
Touch the symbol and enter the
street that intersects the previously
entered street.
Touch the Start Route Guidance button to
start the route guidance.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options
(ch. "Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
–
Using the home address as
destination
If your home address is saved, you can quickly
navigate home from any location. The stored ad-
dress can be viewed in the settings and changed,
if necessary (ch. "Configuring Lucca").
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the symbol.
The route is calculated and the route
guidance started.
Copying the destination from the
favourites
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the symbol.
The Favourites menu is displayed.
Touch the desired destination.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Deleting or renaming a destination (ch.
"Managing destinations")
Planning a tour with the selected destina-
tion (ch. "Tour planning")
Displaying a destination on the
map (ch. "Working with the
map")
Defining route options (ch.
"Specifying route options")
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
–
Lucca3_5B_long_GB_NEU•.indd 15Lucca3_5B_long_GB_NEU•.indd 15 04.10.2007 16:49:30 Uhr04.10.2007 16:49:30 Uhr

16
Navigation
Copying one of the last destinations
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the symbol.
The Last destinations menu is dis-
played.
Touch the desired destination.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Saving or deleting a destination in favour-
ites (ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
Defining route options (ch.
"Specifying route options")
Entering a point of interest
The points of interest or POIs include specific
locations such as parking options and petrol sta-
tions. These points of interest can be used as navi-
gation destination.
Note:
You can only select points of interest that
are contained in the map material.
The point of interest category User POI in
the Points Of Interest menu contains your
personal points of interest. The enclosed
CD/DVD contains the PC tool with instruc-
tions to create your own POIs.
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
쏅
쏅
쏅
쏅
쏅
–
–
–
•
•
쏅
Touch the symbol.
The Points of Interest menu is dis-
played.
You can now select where the desired point of
interest is located.
Selecting a point of interest nearby, in the
destination area or at home
In the Points Of Interest menu, touch
the symbol to select a point of inter-
est nearby.
- or -
In the Points Of Interest menu, touch
the symbol to select a point of inter-
est in the destination area.
Note:
The destination to which you started a route
guidance last is taken as the destination
area.
- or -
In the Points Of Interest menu, touch
the symbol to select a point of inter-
est at the home address.
Touch one of the symbols offered to select a
point of interest category.
A result list is displayed.
Touch an entry of your choice.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (ch.
"Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
Lucca3_5B_long_GB_NEU•.indd 16Lucca3_5B_long_GB_NEU•.indd 16 04.10.2007 16:49:31 Uhr04.10.2007 16:49:31 Uhr

Navigation
17
Displaying a destination on the
map (ch. "Working with the
map")
Selecting a point of interest at a specific
location
In the Points Of Interest menu, touch
the symbol.
The Points Of Interest In Town menu
is displayed.
Touch the symbol to select a differ-
ent country.
A list of the available countries is
displayed.
Touch the country in the list to select it.
The country is selected and the Points Of In-
terest In Town menu is displayed again.
Next, select a city:
Touch the symbol.
The keyboard is displayed.
Enter the city as described in the chapter
"Entering a destination address".
Touch the OK button.
The Town District menu is displayed.
For larger towns, enter the town district.
Touch one of the symbols to select a point of
interest category.
The keyboard is displayed.
Enter the name of the point of interest.
- or -
Touch the List button.
A result list is displayed.
Touch an entry of your choice.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (chapter
"Specifying route options")
–
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
Selecting a point of interest on the map
In the Points Of Interest menu, touch
the symbol.
The map is displayed.
Move and scale the map as described in the
chapter "Working with the map".
Touch a location of your choice.
Touch the button.
The In Map menu is displayed.
Touch one of the symbols offered to select a
point of interest category.
A result list is displayed.
Touch an entry of your choice.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (chapter
"Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
–
–
–
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
–
Lucca3_5B_long_GB_NEU•.indd 17Lucca3_5B_long_GB_NEU•.indd 17 04.10.2007 16:49:31 Uhr04.10.2007 16:49:31 Uhr

18
Navigation
Displaying a destination on the
map (ch. "Working with the
map")
Entering coordinates
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the button.
The display shows the second page
of the menu.
Touch the symbol.
The Destination Coordinates menu
displays.
Touch the symbol and enter the lati-
tude.
Touch the symbol and enter the lon-
gitude.
Always select the cardinal point first and
then enter the values with the corresponding
units.
Touch the OK button.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (chapter
"Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
–
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
–
Selecting a supraregional point of interest
If a point of interest cannot be precisely assigned
to a location, e.g. an airport, a motorways exit
and a mountain pass, you can enter it as a suprar-
egional point of interest.
In the Points Of Interest menu, touch
the symbol.
The Supraregional menu is dis-
played.
Touch the symbol to select a differ-
ent country.
A list of the available countries is
displayed.
Touch the country in the list to select it.
The country is selected and the Supraregional
menu is displayed again.
- or -
Touch one of the symbols offered to select a
specific location, e.g. an airport.
The keyboard is displayed.
Enter the name of the point of interest as de-
scribed in the chapter "Entering a destination
address".
- or -
Touch the List button.
A result list is displayed.
Touch an entry of your choice.
The address of the destination is displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (chapter
"Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
Lucca3_5B_long_GB_NEU•.indd 18Lucca3_5B_long_GB_NEU•.indd 18 04.10.2007 16:49:32 Uhr04.10.2007 16:49:32 Uhr

Navigation | Storing the position
19
Copying a destination from the map
Touch the symbol in the Navigation
menu.
The Destination Input menu is dis-
played.
Touch the button.
The display shows the second page
of the menu.
Touch the symbol.
The map is displayed.
Move and scale the map as described in the
chapter "Working with the map".
Touch a location of your choice.
The city is selected and its name appears
in the lower display bar.
Touch the button.
The coordinates to the selected loca-
tion are displayed.
Touch the Start Route Guidance button.
The route is calculated and the route guidance
started.
- or -
Touch the button to call up the add-
on menu.
You have now the following options:
Defining route options (chapter
"Specifying route options")
Calculating a route (ch. "Calcu-
lating a route")
Saving a destination as favourite
(ch. "Managing destinations")
Displaying a destination on the
map (ch. "Working with the
map")
쏅
쏅
쏅
쏅
쏅
쏅
쏅
쏅
–
–
–
–
Storing the position
You can store your current position and later use
it as a destination.
Touch the symbol in the main menu
of the Lucca.
The map is displayed.
Touch the symbol.
The Navigation menu is displayed.
Touch the symbol.
The Position Information menu is
displayed.
This menu contains this information:
The address of the current location, if it is
contained in the map material
Latitude/Longitude: Current position in
east longitude and north latitude
Altitude: Current height above mean sea
level
The compass: Driving direction (reliable
information after approx. 5 km/h)
Touch the Save As Destination button.
The keyboard is displayed.
Enter a name for the destination and confirm
with OK.
The destination is stored under the name en-
tered in the Favourites menu.
쏅
쏅
쏅
–
–
–
–
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd Abs2:19Lucca3_5B_long_GB_NEU•.indd Abs2:19 04.10.2007 16:49:33 Uhr04.10.2007 16:49:33 Uhr

20
Managing destinations
Managing destinations
Two lists are available in which individual destina-
tions are saved:
In the Favourites
In the Last Destinations list
Destinations from the Favourites can be re-
named.
You can delete individual destinations from both
lists.
Saving destinations
All destinations to which you start a route calcula-
tion (ch. "Calculating a route") are automatically
stored in the Last destinations. The last 20 desti-
nations are stored.
Every destination entered and the destinations
of the Last destinations list can by permanently
stored in the Favourites. This is particularly useful
if you want to approach this destination repeat-
edly.
Storing a destination entered
Prerequisite:
You entered a destination as described in the
chapter "Navigation", "Entering a destination
address".
In the Destination menu, touch the
button to call up the add-on menu.
Touch the symbol.
The keyboard is displayed.
Enter a name for the destination and touch
OK.
The destination is stored in the Favourites
under the name entered.
Saving one of the last destinations
Prerequisite:
You opened the Last destinations list as de-
scribed in the chapter "Copying one of the
last destinations".
Select the destination to be saved in the Last
destinations list.
•
•
•
쏅
쏅
쏅
•
쏅
Touch the button to call up the add-
on menu.
Touch the symbol.
The keyboard is displayed.
Enter a name for the destination and touch
OK.
The destination is stored in the Favourites
under the name entered.
Renaming a destination (favourites
only)
You can rename a stored destination in the Favour-
ites:
Prerequisite:
You opened the Favourites menu as described
in the chapter "Navigation", "Copying a desti-
nation from the favourites".
In the Favourites menu, select the destination
to be renamed.
Touch the button to call up the add-
on menu.
Touch the symbol.
The keyboard is displayed.
Enter a new name for the destination and
touch OK.
The destination is stored in the Favourites
under the name entered.
Deleting a destination
You can delete a destination stored in the favour-
ites or a last destination:
Prerequisite:
You entered a destination as described in the
chapter "Navigation", "Copying one of the last
destinations".
- or -
You opened the Favourites menu as described
in the chapter "Navigation", "Copying a desti-
nation from the favourites".
Select the destination to be deleted.
Touch the button to call up the add-
on menu.
쏅
쏅
쏅
•
쏅
쏅
쏅
쏅
•
•
쏅
쏅
Lucca3_5B_long_GB_NEU•.indd 20Lucca3_5B_long_GB_NEU•.indd 20 04.10.2007 16:49:33 Uhr04.10.2007 16:49:33 Uhr