Blue Ox BX2239 User manual

Page 1 of 8 292-2726 Rev. C 7/20/10
Please read BOTH these Installation Instructions and the General
Instructions before attempting to install or operate this equipment.
1. Blue Ox®towing products and accessories
are intended to be installed by Blue Ox®
Dealers who are familiar with our products and
have the equipment necessary and knowledge
to do “fit work”. When necessary Blue Ox®
Dealers can be found at www.blueox.com or
by contacting our Customer Care
Department at [phone].
2. Many Blue Ox®Baseplates are designed to
use existing holes and hardware to mount
the baseplate to the towed vehicle. Even
though bolts are there, do not assume they
are adequate for baseplate mounting. Always
use hardware supplied in the hardware kit
and existing hardware specified in the
Baseplate Installation Instructions.
Confirm the towability and pre-towing
procedures for your vehicle with
the owner’s manual or contact the
vehicle’s manufacturer for specific
towing procedures.
Attachment Tab Height: 26 1/4”
Attachment Tab Width: 25”
2006-10 Honda
Ridgeline
Installation Instructions
BX2239
Bolt Size Grade 5 Grade 8
1/4” 10 14
5/16” 19 29
3/8” 33 47
7/16” 54 78
1/2” 78 119
5/8” 154 230
Bolt Torque Specifications
Torque in Foot-Pounds for Inch Bolts
Bolt Torque Specifications
Torque in Foot-Pounds for Metric Bolts
Bolt Size Grade 8.8 Grade 10.9
6MM 6 8
8MM 16 22
10MM 31 40
12MM 54 70
14MM 89 117
Serial Number
!
Failure to read and follow these instructions
could result in separation of the towed vehicle
from the tow bar, causing property damage,
loss of towed vehicle, personal injury or death.
WARNING
If the front of your vehicle looks different
If the front of your vehicle looks different
than this, call us at [phone].
than this, call us at [phone].

Page 2 of 8 292-2726 Rev. C 7/20/10
Parts List
Ref. No. Qty. Part # Description
1 1 61-6127 Weldment, Baseplate, BX2239
2 4 61-5589 Nut Plate, 3/8-16 Nut, w/ 14” Wire
3 4 61-5208 Wld, Nut Plt 1/4X1X1, 3/8”/14”Wire
4 2 102-6682 Backing, Plate, BX1015
5 4 201-0418 8MM-1.25 X 35MM Hex Bolt Grd.8.8 ZP
6 4 203-0102 8MM Lock Washer, ZP
7 4 203-0002 5/16 Flat Washer, ZP
8 12 201-0440 3/8-16 X 1 1/2 Hex Bolt, Grd.5, ZP
9 12 203-0010 3/8 Lock Washer, ZP
10 4 203-0003 3/8 Flat Washer, ZP
11 4 202-0003 3/8-16 Hex Nut, ZP
12 2 201-0553 1/4-20 X 1/2 HX.Wshd.Type F Tcs, ZP
13 2 201-0192 10-32 X 1/2 Slot, RD. HD. Screw
14 2 203-0054 #10 Lock Washer
15 2 202-0047 #10-32 Hex Nut
16 2 101-5822 Adapter, 4 Way Connector
17 2 62-3468 Att TabAssy, Rem, SF/SB, 1 Hole
2 226-0046 Baseplate Safety Cable, 36” CL III (Not Shown)
4 229-0359 Quicklink, 3/8, ZP (Not Shown)
2 290-0437 Cap Plug, Black (Not Shown)
Important:
Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt
is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of
the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered
through your nearest Blue Ox® Dealer or Distributor, or call our Customer Care Team at [phone]. Failing to follow
and/or altering these installation instructions in either installation or required equipment will void the manufacturer’s warranty.
Tools Required
8MM Socket
10MM Socket
12MM Socket
9/16” Socket
13/32” Drill Bit
Utility Knife
Phillips Screwdriver
Reciprocating Saw
Vise Grip
LOCTITE Red
2006-10 Honda Ridgeline
Installation Instructions
BX2239

Page 3 of 8 292-2726 Rev. C 7/20/10
Attachment Tabs:
Due to the design of the removable tabs, the
RangeFinder II and Ambassador tow bars can not
be used. Adapters, except the BX8833 and the
BX88151, can not be used with this baseplate.
Instructions:
The front fascia, headlights, horn bracket,
and bumper are removed for the baseplate
installation. Drilling is required. Trimming of
the air dam is required.
The dimensional variations between otherwise
identical vehicles can be considerable.
While the baseplate was designed for easy
installation, it may be necessary to tailor the
baseplate slightly to compensate for auto
manufacturer’s tolerances. These minor
adjustments may include filing a hole slightly,
bending electrical rods or bending end plates.
The BX8869 Bulb and Socket Wiring Kit is
recommended for this vehicle.
1. Remove 12 pushpins from the plastic above the
radiator. Remove the plastic from the top of the
radiator. Set pushpins aside to reinstall later.
2. Just forward of the front tire, on the edge of the
fascia, use an 8MM socket or Phillips screwdriver
to remove one metric bolt. Set bolt aside to reinstall
later. Do this to both sides of the vehicle.
2
2


2006-10 Honda Ridgeline
Installation Instructions
BX2239


1
1










Installation Instructions:




Possible Location for the BX8869
Possible Location for the BX8869
Bulb and Socket Wiring Kit.
Bulb and Socket Wiring Kit.
Handling of some cosmetic parts
when installing this product may
require the use of protective covers,
rags, specialty tools, etc. to prevent
damage.

Page 4 of 8 292-2726 Rev. C 7/20/10
3. Just forward of the front tire, on the outermost
bottom edge of fascia, remove two metric bolts
using a 10MM socket. Do this to both sides of the
vehicle. Set bolts aside to reinstall later.
3
3
6. Remove another push pin from underneath, gray
arrow. Remove the two bolts on the side. Using
a 12MM socket, remove the bolt from the horn
bracket, bottom arrow. Do this to both sides of the
vehicle. Set push pins and bolts aside to reinstall
later.
6
6




4. Using a 10MM socket, remove three metric bolts
that run horizontally along the bottom of fascia,
where the belly pan and fascia meet. Set bolts
aside to be reinstalled later.
4
4






5. Remove the metric bolt, using an 10MM socket.
Also remove the push pin above the headlight, gray
arrow. Do this to both sides of the vehicle. Set
bolts and push pins aside to reinstall later. Start
fascia removal by pulling down on the fascia where
it meets the fender, just forward of the front tire.
While still on the side of the vehicle, pull fascia
slightly forward. Do the steps above to both sides
of the vehicle. From the front of the vehicle, pull
fascia forward to remove. Set fascia aside carefully
to reinstall later.
2006-10 Honda Ridgeline
Installation Instructions
BX2239
5
5













7
7
7. Remove this bolt on the side. Do this to both sides
of the vehicle. Set bolts aside to reinstall later.
Page 5 of 8 292-2726 Rev. C 7/20/10
2006-10 Honda Ridgeline
Installation Instructions
BX2239


8. Using a Phillips screwdriver, remove the screw. Do
this to both sides of the vehicle.
8
8


10. Lay the bracket of the metal bumper on a solid
surface. Use a hammer to pound and flatten the rib
on top of the bracket. Do this to both sides of the
vehicle.
10
10
9. Using a 12MM socket, remove two metric bolts on
the top and one metric bolt underneath the metal
bumper. Do this to both sides of the vehicle. Set
bolts aside to reinstall later.
9B
9B






9A
9A
When using power drills be aware of the
dangers of torque and drill bit length.

Page 6 of 8 292-2726 Rev. C 7/20/10
12. Using a vice grip; clamp the rear of the baseplate
to the webbing. Using the baseplate as a template,
drill into the frame rail through the three baseplate
holes using a 13/32” drill bit. Remove the two bolts
and pull the bolt out of the bottom. Remove the
bumper. Line up the baseplate with the back hole.
Guide a 3/8-16 nut plate through the frame opening
and align with bolt hole. Insert the 3/8-16 hex bolt
into those bolt holes with the 3/8 lock washer and
hand tighten. Do this on both sides of the vehicle.
Be sure to use LOCTITE Red on ALL bolts.
12
12


2006-10 Honda Ridgeline
Installation Instructions
BX2239


13. Temporarily slide the metal bumper in between the
frame and the baseplate. Insert additional bolts
and tighten using Loctite. Torque to specs. Do this
on both sides. Drill the side hole being sure not to
drill into the radiator, use a socket over the drill bit.
13
13
BE SURE TO USE LOCTITE®RED ON ALL BOLTS
BEFORE TIGHTENING. TIGHTEN ALL BOLTS
ACCORDING TO THE TORQUE CHART ON THE FRONT
PAGE OF THESE INSTRUCTIONS OR ON PAGE 3 OF
THE BASEPLATE TOWING GENERAL INSTRUCTIONS.


11
11
11.Slide metal bumper back on to the frame rail,
guiding the baseplate on top of frame rail. Align
with the existing holes of the bumper bracket.
Insert two 8MM-1.25 x 30MM hex bolts through
the baseplate into the two existing bumper bracket
holes using 5/16” lock washer and 5/16” flat
washers Snug the bolts down. Do this on both
sides.


14. Remove metal bumper. Insert the 3/8-16 hex bolts
with the 3/8” lock washer through the baseplate
holes on the side of the frame rail. Hand tighten
bolts to the 3/8-16 nut plates placed on hex bolts
through opening in frame end. Do this to both
sides of the vehicle. Using diagonal cutters, cut
all nut plate wires flush with the end of the frame.
Reinstall bumper and tighten bolt for steps 12, 13
and 14. Be sure to apply LOCTITE Red to ALL
bolts.




14
14

Page 7 of 8 292-2726 Rev. C 7/20/10
2006-10 Honda Ridgeline
Installation Instructions
BX2239
18. Just outside the driver’s side radiator, trim the air
dam up 1 1/2”, follow the top of the ridge all the
way across.
18
18


17. Reinstall the horns using the 12MM socket. Put
the headlight assemblies back on and plug in. Do
this to both sides of the vehicle.
15
15


15. Insert the 3/8-16 hex bolts with the 3/8” lock
washer through the baseplate holes on the side
of the radiator support. Then tighten bolts to the
3/8-16 nut plates on back side of radiator support.
Do this to both sides of the vehicle. Using diagonal
cutters, cut all nut plate wires flush with the end of
the frame. Be sure to apply LOCTITE Red to ALL
bolts.
16
16




19. Trim 4 1/2” across, leave the tab by cutting below
the tab.
19
19




16. Place the backing plate on the bottom side of the
frame webbing to align with drilled holes, insert
the 3/8-16 x 1 1/2” hex bolts and 3/8” flat washers
into this hole, tighten the 3/8-16 hex nuts and 3/8”
lock washers. Reinstall the air baffle to its original
position.
Install the tow bar and safety cables according
to their instructions. When demonstrating this to
the customer, be sure to include all of the Blue Ox
packaging and contents.
Reinstall fascia. Be sure to install all pushpins and
bolts.
Baseplate Installation is now Complete.

CUSTOMER SERVICE COMMITMENT
Blue Ox is committed to providing you with
exceptional customer care throughout your lifetime
with our products. Our team is here to assist you
with any questions you may have regarding the
performance of your product. Simply call (402)
385-3051 and you can speak with our customer
care team.
Additionally, please visit our website to see
which rallies our Destination America team will
be attending. For a nominal fee, our service
technician will service your towing system to
ensure it’s in proper working condition. Also as
a commitment to our customers, should you visit
our factory you can stay at our full service Blue
Ox campground at no charge along with enjoying
a factory tour.
Again thank you for being our customer and for
the confidence you have shown in the performance
of our products. It is because of customers like
you we enjoy the success we have today.
© 2009, 10 Blue Ox
One Mill Road, Industrial Park
Pender, Nebraska 68047
Phone: [phone]
Toll Free: [phone]
Fax: [phone]
www.blueox.com
Page 8 of 8 292-2726 Rev. C 7/20/10
With removable tabs installed.
With removable tabs installed.
2006-10 Honda Ridgeline
Installation Instructions
BX2239
Be sure that ALL electrical connections
are plugged in properly and functioning
BEFORE Installing the fascia.
DEALER OR INSTALLER:
Be certain the user receives the
instruction sheets for their products.
If the baseplate is in an accident, it must
be replaced. DO NOT use it again! An
accident can cause unseen damage and
using it again could result in more dam-
age or serious injury. DO NOT use the
baseplate if it is damaged or missing parts.