bluechem TOOLS EQUIPMENT ATF EVOLUTION PREMIUM User manual

ATF EVOLUTION PREMIUM
Cleaning and service device
for automatic transmissions

ENGLISH
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
The equipment is for specialist or quali-
ed technician use only.
Disclaimer
- All information, illustrations, and
specications contained in this manual
are based on the latest information
available at the time of publication.
- CTP GmbH reserves all the rights to
make changes at any time without
notice.
Safety Precautions
Read all service procedures and precau-
tions, installation instructions and equip-
ment operating manuals thoroughly.
Failure to observe these precautions, or
the improper use of equipment, could re-
sult in property damage, serious injury or
death. Never allow improperly trained
personnel to perform these procedures
or operate equipment.
- Read and understand the User’s Manual
before attempting to operate the ATF
EVOLUTION PREMIUM
- Do not smoke in proximity to the ma-
chine while it is in operation.
- Do not use the machine in proximity to
sources of heat and re.
- Do not expose to direct sunlight or
rain, use in well-ventilated work area
only.
- Turn o the power after the operation is
completed.
- When it is in operation, keep the hoses
away from rotating elements and hot
parts such as cooling fans, radiators, etc.
- Vehicle exhaust includes various
poisonous and harmful gases (such
as carbon monoxide, hydrocarbon, nit-
rogen oxygen complex, etc.). Keep the
unit in a well ventilated work area when
performing operation and wear safety
goggles, respirator and clothes.
- The operator should keep away from
the heat parts such as exhaust hoses
and radiator to avoid the personal
injury.
- When disconnecting any connector
of the pressurized uid pipe, wrap the
connector with towel to prevent the
uid from spurting out.
- The children and mental retardation
personnel should keep away from the
unit during operation.
- The operator should be quite familiar
with the shift of automatic transmission
to avoid transmission damage caused
by improper operation.
- Always make the drive wheels hanging
when cleaning the transmission or
exchanging uid.
- The unit should be placed vertically and
should not be placed upside down.
- When changing uid, the operati-
on should be performed by properly
trained personnel.The quality of the
selected ATF must conform to the
direction as specied in the manual of
the auto to be operated. Otherwise, CTP
GmbH shall not be liable for any direct
or consequential damages.
Note: specifying operations
that require attention when
operatingthe equipment.
Warning:Specifying apossi-
ble hazardthat couldresult
in damage to the machine or
personalinjury.

ENGLISH
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
Introduction______________________________________1
Features_________________________________________1
Working Conditions _________________________________1
Specications _____________________________________1
Structure ________________________________________2
1. Outline __________________________________2
2. Overall structure_____________________________3
3. Pipeline diagram ____________________________4
4. Circuit connection diagram ______________________4
5. Control panel_______________________________5
1. Startup interface ___________________________ 6
2. Main menu ________________________________ 6
Operations _______________________________________7
1. Preparation________________________________7
1.1 Jack vehicle_______________________________ 7
1.2 Connecting hose __________________________ 7
1.3 Power cables connection____________________ 7
2. Filling liquid _______________________________8
2.1 Filling detergent___________________________ 8
2.2 Adding new oil____________________________ 8
3. Circulating cleaning___________________________8
3.1 Fill detergent to auto transmission ____________ 8
3.2 Fill Circulating cleaning _____________________ 8
3.3 Finish cleaning ____________________________ 9
4. ATF exchange ______________________________9
4.1 Direct Input ______________________________ 9
4.2 Database enter____________________________ 10
5. Adjusting uid level___________________________12
5.1 Increase uid amount ______________________ 12
5.2 Decrease uid amoun ______________________ 12
6. Empty new uid tank__________________________13
7. Empty used uid tank _________________________13
8. System setting______________________________13
8.1 Sensor calibration _________________________ 14
8.2 Select transmission uid ____________________ 16
8.3 Window Light Switch Setting ________________ 16
8.4 LCD Screen Brightness Adjustment____________ 16
8.5 Date & Time ______________________________ 17
8.6 Language setting __________________________ 17
8.7 Database Entry ____________________________ 18
8.8 Print Information __________________________ 19
8.9 Device information_________________________ 19
Main Adapters ____________________________________21
Warranty ________________________________________24
Table of Contents

ENGLISH
1
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
Features
- LCD display and personalized design
making easy operation.
- Multi-language print.
- Filling and recycling of automatic trans-
mission uid.
- Automatic identication for the uid ow
inlet/outlet direction.
- Circulating cleaning for automatic trans-
mission.
- Easy for detergent lling.
- Automatic exchange of new/used uid.
-Visual display of the uid pressures.
- Accurate display of the automatic trans-
mission uid temperature.
- Intelligent electronic control for the full
automatic equivalent exchange of new
and used uid.
- Manually adding and upgrading database
function.
-Various special adapters are applicable to
vehicle types made in Europe, America
and Asia.
- Eectively resolve the incomplete uid
exchange of manual operation.
- It improves the working performance
of auto transmission.
- It prolongs the work life of transmission.
Working Conditions
- Ambient temperature: -10~+50°C
- Relative humidity: <90%
Specications
- Power supply: AC 110V/60Hz or AC
220V/50Hz
- Maximum power: 150W
- Pressure gauge: 0~200psi
- Fluid outlet hose: 3 m
- Fluid return hose: 3 m
- Fluid draining hose: 1.2 m
- Filter precision: 5µm
- Fluid tank: 20 ltr x 2
- Equivalent exchange error: ±100ml
- Mean exchange speed: 2 ltr/MIN
- Noise: <70db
- Net weight: 70 kg
- Gross weight: 78 kg
- Size: 590 mmx700mmx1037mm
Introduction
The transmission uid inside transmission will go bad after a period of usage of auto-
matic transmission. If the transmission uid can not be changed completely in time, it
may cause the abnormality to the transmission. Generally speaking, auto transmission
uid changer can not control the lling quantity of the ATF as required, the excessi-
ve or shortage lling will cause the damage to auto transmission. ATF EVOLUTION
PREMIUM auto transmission changer can complete the ush and uid exchange in
20 minutes for transmission, torque converter and radiator. The uid exchange rate is
nearly 100%.

ENGLISH
2
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
Structure
1.Outline
As shown in Fig. 1, ATF EVOLUTION PREMIUM is designed with a ne cabinet.There is
a handle at the top of cabinet and two pairs of casters at the bottom of the cabinet,
which makes it easy to move the unit. Fluid hoses are equipped with proper
connectors for fast connection. The intelligible control panel helps you operate the
machine easily.
1 Sight indicator of used fluid
2 Sight indicator of new fluid
3 Power plug hole
4 Power switch
5 Operation screen
6 Fluid filling port
7 Fluid draining hose
8 Hose
9 Hose
10 Printer
11 Detergent container
12 Filter
13 Filling opening for flushing liquid
Fig. 1

ENGLISH
3
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
2.Overallstructure
SN ERP Code Name SN ERP Code Name
1X103201682 Bottom board 17 Filter
2103200444 Sensor cushion plate 18 Filling opening for
Flushing Liquid
4Z205010377 Front caster 19 X103202568 Lower hinge joint
welding body
5102240004 Front right post 20 103160062 Control panel
6X103201715 Right side board 21 103230149 Rear left post
7103202165 Hose brackets 22 X103240250 Left side board
8107040084 Back caster 23 103202287 Caster axle
9X103201687 Tray for tank 24 103201667 Front board
10 X103201683 Filling bucket 25 103260005 Front left post
11 199010013 Rear right post 26 103202285 Cover of back caster
12 103200355 Door board
13 X103201680 Middle spacer plate 01
14 103202155 Handle
15 103240243 Top board
16 102990097 Oil trap
16a 102990096 Filter plate
16b 103230148 Oil trap cover board
1234567826
14 15 16
9
10
11
12
13
16a 16b 19 20 21 22
23
24
25
Fig. 2
17
18

ENGLISH
4
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
3.Pipeline diagram
J8 To solenoid V2 J25 To unit serial port cable
J12 To solenoid V1 J14 To temperature sensor
J17 To solenoid V3 J15 To used uid tank sensor
J22 To solenoid V4 J16 To new uid tank sensor
J21 To oil pump J13 To key-press lm
J24 To switch power supply J2 To unit USB cable
J26 To printer power supply J3 Test port, used by CTP GmbH only
J23 To printer data cable J4 To sight indicators for used & new uid
4.Circuit connection diagram
1 Pump
2,3,15 Three-way solenoid valves
4 Fluid lling port
5 New uid tank
6,8 Electronic scales
7 Detergent container
9 Used uid tank
10,17 Filters
11 Fluid path identier
12,18 Pressure gauges
13,14 Sight indicators
16 Two-way solenoid valve
19 Check valve
20 Ball valve for uid draining
21 Temperature sensor
J22
J21
J24J25
ATF EVOLUTION PREMIUM
Control Board
(200 x 125 mm)
J2 J3 J4
J8
J12
J17
J23
J26
J14
J15 J16
Fig. 4
Fig. 3
J13

ENGLISH
5
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
5.Controlpanel
Element Description
1NEW Observe the ow rate and compare the color of new and used uid. Display the uid
outlet pressure. Display the uid pressure of AT radiator.
1USED
2ÛPress it to select function option in main menu.
2ÜPress it to select function option in main menu.
3ENTER Conrmation.
4RETURN 1. Menu to return.
2. Press one time to stop current operation, and press once more to return to previous
interface.
5DEL Press to delete the previous character in focused window, and in database inter-
face, press it you can delete some menu item.
6LIGHT 1. In main-menu, you can switch on/o the lights of sight indicators.
2. In focused window, press it you can enter the character of “.”
3. When entering some menu option on database interface, press it you can switch
between uppercase and lowercase letters.
7Numpad 0(A, B, C)
1(D, E, F)
2(G, H, I)
3(J, K, L)
4(*)
5(M, N, O, P)
6(Q, R, S)
7(T, U, V)
8(W, X, Y, Z)
9(#)
Fig. 5
1
1
7
2
2
3
4
5
6

ENGLISH
6
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
1.Startupinterface (as shown in Fig. 6):
In the startup interface press any key to enter the upgrade database and multilingual
document interface.
2. Main menu
The main menu of display screen is as shown in Fig.7
Fig. 6
Fig. 7
Item Description
Add detergent Add ATF detergent to AT
Exchange Exchanging ATF
Adjust uid level Adjusting the quantity of uid inside AT
Empty new tank Draining left uid inside new uid tank
Empty used tank Draining used uid inside used uid tank
System setting Modifying the system parameter, e.g.: Calib-
ration of electronic scale, adjusting contrast,
language selection, database entry.

ENGLISH
7
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
Operations
Note:
During the unit is in operation, it will produce the vibration with a certain
frequency and noise.This is the normal performance. Do not take it as the
malfunction.
1.Preparation
1.1Jack vehicle
Jack the vehicle to keep the drive wheel
o the ground at least 200 mm, apply
the parking brake and block the driven
wheels in front and behind.
1.2Connecting hose
1) Locate the uid hose that is
connected between the radiator and
transmission at the most convenient
location and then disconnect
the adaptor. Locate the matched
connector inside the connector box
and connect it to the disconnected
adapter.
2) Connect the two hoses marked
“TO TRANSMISSION”of ATF EVOLUTION
PREMIUM to the disconnected two
ends of the hoses of automatic
transmission (no necessary to consider
the direction of the uid ow). Refer to
Fig. 8.
1.3Powercables connection
Connect the power cables of the main
unit to the designed power supply.
1.4Check-up
1) Start the engine, and ensure that
there is no leakage in pipeline.
2) Conrm that the power supply of the
ATF EVOLUTION PREMIUM is normal,
and then switch on the unit.
Fig. 8
to transmission

ENGLISH
8
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
2.Filling liquid
2.1Fillingdetergent
When you are ready to perform
the circulating cleaning for auto
transmission, please ll proper
amount of detergent into the
detergent container. ( See page 3 Fig.
2, No. 18)
2.2Adding newoil
When you are ready to perform the
ATF exchange operation, please ll
new uid into the new uid tank from
the uid lling port.
3.Circulating cleaning
3.1Filldetergentto auto transmission
1) Select the function of“Add ATF
detergent”in main menu, and set the
amount of the detergent to be lled
(the setting range: 0.00-0.50 ltr). Refer
to Fig. 9.
Note: Fill detergent before need
to calibrate cleaning speed (see
„cleaning speed“ sensor calibration
content).
2) Input the amount to be lled. The
default value of the unit is 0.20 ltr
and the maximum value is 0.50 ltr.
Press ENTER key after the amount to
be lled is conrmed, the detergent
lled inside the detergent container
will be pumped into the hose.
3) After the lling operation is
nished, the system will automatically
pop up print menu. Press ENTER key
select print, press RETURN key to
cancel printing. Refer to Fig. 11.
4) Print is completed or cancelled,
will pop up 10 minutes cycle cleaning
countdown. Refer to Fig. 12.
Fig. 9
Fig. 10
Fig. 11
Fig. 12
3.2Circulatingcleaning
After lling the detergent you start the
engine.The cleaning process starts and
restarts automatically when all hoses are
connected properly. Cycle through all the
gears for each one minute, to speed up
the process.

ENGLISH
9
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
For optimum cleaning eect, the vehicle
speed in top gear should be at least 60
km/h. 80 km/h or 50 mph should not be
exceeded for safety reasons.
3.3Finishcleaning
After about ten minutes, you can turn
o the engine of the vehicle, thus the
cleaning is stopped.
4.ATF exchange
When dierent kind of uid is used or the
unit is stored for a long time, about 0.5 ltr
new uid should be lled into new uid
tank. With the way of emptying the new
uid tank, clean the uid hoses and drain
the air bubbles out from the unit.
1) Start the vehicle to warm up
the uid inside the transmission
to normal temperature and ll the
new transmission uid with desired
amount into it.
2) Check if the pipelines are well
connected.
3) ATF exchange: as shown in Fig.
13, you can directly input the uid
amount to be changed, as well as
you can obtain the amount from the
database.
4.1Direct Input
Select Direct Input, and press ENTER key
to enter into the next interface, and then
input the uid amount to be changed
(the default value is 10 ltr), as shown in
Fig. 14.
Be sure that there is no leak in the pipe-
lines and press ENTER key to exchange,
as shown in Fig. 15.
After the exchange operation is nished,
the system will automatically pop up
print menu. Press ENTER key select print,
press RETURN key to cancel printing.
Refer to Fig. 16.
Print is completed, return to Fig. 13
interface.
Fig. 13
Fig. 14
Fig. 15
Fig. 16

ENGLISH
10
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
4.2Databaseenter
1. Select and database enter, press
ENTER key you can see the vehicle
model menu as shown in Fig. 17.
2. Select the menu path of the specic
vehicle model to enter the testing
interface which displays the uid
amount to be changed, as shown in
Fig. 18.
3. If the testing is not passed, the screen
will display the operations which
need to be performed, as shown in
Fig. 19, Fig. 20, Fig. 21 and Fig. 22.
4. The system starts to drain the used
uid.You can wait for nish, as well as
you can press RETURN key to stop the
operation and return to the previous
menu. As shown in Fig. 23.
5. The system starts to drain the used
uid.You can wait for nish, as well as
you can press RETURN key to stop the
operation and return to the previous
menu.
As shown in Fig. 23.
6. The interface prompts: Emptying OK!
After the testing is passed, please
press ENTER key to perform ATF
Change while displaying progress bar
and the waveforms for the change of
new/used uid. As shown in Fig. 24.
7. After ATF Change nished, the screen
will display the amount of the new
uid changed, the amount of the
used uid changed, and the error
between them, while printing out the
amount of the new uid which has
been changed.
Press RETURN key to return to the pre-
vious menu.
1) Check the uid level inside trans-
mission. If the level is not enough,
supplying uid is required. Refer
to the section of Adjust uid level
for the detailed operation.
2) Disconnect the unit and resume
the hoses of the transmission.
Fig. 17
Fig. 18
Fig. 19
Fig. 20
3) Start the engine and check if the-
re is oil leakage in the on-vehicle
pipelines.

ENGLISH
11
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
Fig. 23
Fig. 24
Note:
• Switch each gear when exchanging.The time of each shift should stay about 1 minute, which depends
on actual situation. When the vehicle is running at high-speed gear and accelerate the speed to more
than 60 km/h, the ATF inside uid control pipeline can be exchanged. 80 km/h or 50 mph should not
be exceeded for safety reasons.
•The oil lters should be replaced every 20-30 applications.
•To ensure the exchange quality, the quantity of new uid inside the unit should be 2~3 ltr. more than
that of the uid required by automatic transmission.
• Do not add new uid from the new tank during the running period of exchange. Otherwise, the
operation will result in inequality amount. If there must be added the new uid, ll after this exchange
process is completed!
Fig. 21 Fig. 22

ENGLISH
12
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
5.Adjusting uidlevel
5.1Increaseuidamount
When the uid in transmission is not
enough, supply it with the desired
amount of uid. Select this operation.
1) Enter the menu of Adjust uid
level, select‘Filling’, it indicates
that the uid is being lled into
the transmission. The maximum
of the adjustment is the uid
amount inside new tank. The
interface is as shown in Fig. 25.
2) Input the amount to be lled,
press ENTER key. As shown in Fig.
26.
3) When the recharging is comple-
ted, the system will.automatically
pop up print menu. Press ENTER
key select print, press RETURN key
to cancel printing. Refer to Fig. 27.
Fig. 25
Fig. 26
Fig. 27
5.2Decreaseuid amount
If the quantity of the ATF is more than
the standard amount, it is necessary to
decrease the uid amount inside trans-
mission (Lower the uid level).
1) Enter the menu of Adjust uid
level, select‘Draining’, it indicates
that the uid inside transmission
is being drained, as shown in Fig.
25.
2) Input the amount to be
drained,Press ENTER key, start
the engine, and then the unit will
drain the set quantity of ATF to
used uid tank.
3) After the adjustment is comple-
ted and the unit will prompt to
nish. The system will automati-
cally return to the main menu.

ENGLISH
13
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
6.Empty newuid tank
1. Be sure that the two hoses marked
with“TO TRANSMISSION”are not
connected with the vehicle to be
maintained.
2. Open the handle valve on the uid
hose marked with“EMPTY”, and then
place the hose into container.
3. The system will enter into the inter-
face for Empty new tank, and automa-
tically start uid draining operation,
as shown in Fig. 28.
4. The unit will drain uid until the
hose marked with“Empty”has no oil
draining or press RETURN key to stop
draining operation.
Fig. 28
Fig. 29
7.Empty used uid tank
1. Be sure that the two hoses marked
with“TO TRANSMISSION”are not
connected with the vehicle to be
maintained.
2. Open the handle valve on the uid
hose marked with“EMPTY”, and then
place the hose into container.
3. The system will enter into the
interface for Empty used tank, and
automatically start uid draining
operation.
4. The unit will drain uid until the
hose marked with“Empty”has no oil
draining or press RETURN key to stop
draining operation.
8.Systemsetting
1. Select system setting item in main
menu, press ENTER key.
2. In the sub-item of system setting,
select the desired setting item. The
interface is as shown in Fig. 29.

ENGLISH
14
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
8.1Sensor calibration
1. Select the item for sensor calibration,
press ENTER key to enter the sensor
calibration menu as shown in Fig. 30.
2. Press ENTER key to select the item for
new uid tank calibration, the inter-
face is as shown in Fig. 31.
3. According to the prompts on the
interface, enter the weight value of
the weight, and then press ENTER key.
The interface is as shown in Fig. 32.
4. Remove the new uid tank. When the
value displayed on the interface is
stable, please press ENTER key to save
the data. The interface is as shown in
Fig. 33.
5. Put the weight on the plate. When
the value displayed on the interface
is stable, please press ENTER key to
continue.The interface is as shown in
Fig. 34.
6. When the value displayed on the
interface is stable, please press ENTER
key again to save the data. The inter-
face is as shown in Fig. 35.
7. Remove the weight, and then place
the empty new uid tank on the pla-
te.When the value displayed on the
interface is stable, please press ENTER
key to save the data. The sensor calib-
ration for new uid tank is completed.
When lling the new uid into new
tank, the display screen will display
the quantity of the uid.
The calibration way for used uid tank is
the same as that of the new uid tank.
8. Select“Temperature Sensor”calib-
ration item in Main Menu of [Sensor
Calibration], and then press ENTER
key to enter, the interface is as shown
in Fig. 36.
9. According to the prompts on the in-
terface, enter the current temperature
value (Unit: °C), and then press ENTER
Fig. 30
Fig. 31
Fig. 32
Fig. 33
Fig. 34

ENGLISH
15
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
The interface is as shown in Fig. 39.
13.According to the prompts on the
interface, enter the amount (such as
0.3ltr) of detergent to be added into
the system, and then press ENTER
key to start adding. The interface is as
shown in Fig. 40.
14.Observe the measuring cup’s scale
change status, press ENTER key
to save the speed value when the
detergent amount in the standard
measuring cup is decreased by 0.3ltr
The Cleaning Speed calibration is
nished.
key to save the data. The interface is
as shown in Fig. 37.
10.When the value is stable, press ENTER
key again to nish the temperature
sensor calibration.
11.Select“Cleaning Speed”option in the
Main Menu of [Sensor Calibration],
and then press ENTER key to enter the
interface as shown in Fig. 38.
12. According to the prompts on the
interface, load a certain amount of de-
tergent to a standard measuring cup,
and then press ENTER key to continue.
Fig. 35 Fig. 36
Fig. 37Fig. 38
Fig. 39 Fig. 40

ENGLISH
16
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
8.3WindowLightSwitchSetting
Select Window Backlight Switch and
press ENTER key to enter the setting
interface as shown in Fig. 42. Press ENTER
key to select on or o.
Fig. 41
Fig. 42
Fig. 43
8.2Selecttransmission uid
This function can choose the type of
transmission uid.There are four types
and a kind of other types, if you don‘t
clear transmission uid species, can
choose other. As shown in Fig. 41.
8.4LCD Screen Brightness Adjustment
Select LCD Screen Brightness and press
ENTER key to enter the setting interface
as shown in Fig. 43. Press [UP]/[DOWN]
key to select the desired brightness, and
press RETURN key to conrm and return.

ENGLISH
17
ATF EVOLUTION PREMIUM - Cleaning and service device for Automatic Transmissions • • • User‘s manual
8.5Date&Time
Select [Date & Time] option on the Main
Menu of [System Setting] and then
press ENTER key to enter the interface as
shown in Fig. 44.
a) Set Date
On the menu of [Date & Time], please
select [Set Date] option, and then
press ENTER to conrm, the interface
is as shown in Fig. 45.
According to the prompts on the inter-
face, enter the date (4 bits for year, 2 bits
for month and other 2 bits for date), and
then press ENTER key to conrm.The
interface prompts“OK”.
b) Set Time
On the menu of [Date & Time], please
select [Set Time] option, and then
press ENTER to conrm, the interface
is as shown in Fig. 46.
According to the prompts on the inter-
face, enter the time (2 bits for hour and
other 2 bits forminute), and then press
ENTER key to conrm. The interface
prompts“OK”.
c) Select Date Format
On the menu of [Date & Time], please
select [Set Date Format] option, and
then press ENTER to conrm, the inter-
face is as shown in Fig. 47.
Select the desired date format, and then
press ENTER key to conrm.
Fig. 46
Fig. 48
Fig. 47
Fig. 44
Fig. 45
8.6Language setting
Select the language setting and press
ENTER key to enter the setting interface
as shown in Fig. 48. Press [UP]/[DOWN]
key to select the desired language, and
then press ENTER key to conrm and
return.