BMW PIP Installation and operation manual

BMW PIP User manual
子母畫面介面說明書
3/5/6 系列 X5, X6

-. Precaution ……………………………………………………………… P 3
-. Updated points on this version………………………………………P 4
-. Main Spec.………………………………………………………………P 5
-. System Composition……………………………………………………P 6
-. Outline Dimension ………………………………………………………P7
-. External Appearance……………………………………………………P8
-. Connector Pin Assignment ……………………………………………P10
-. DIP Switch Setting ………………………………………………………P12
-. How to use Remote……………………………………………………P14
-. OSD (On Screen Display) ……………………………………………P15
-. How to use parking guide line …………………………………………P19
-. CAN Wiring & Steering wheel button……………………………………P21
-. Product Composition ……………………………………………………P22
-. Installation manual ……………………………………………………P23
-. FAQ …………………………………………………………………………P24
-2-
INDEX

-3-
Precaution
- You must keep the car key taken off from the car while you work
this and finally, connect power of the interface.
- When to connect the interface cable, you must keep the power
cable taken off.
- You must work this at the environment without any static electricity
or damages.
- All of process on this installation should be done by professionals.
- You must not break the labels attached on the board, if it’s broken,
no warranty.
- When you receive this package you have to check whether there’s
any parts not included and you have to contact us right away.
- Our repair service do not accept any problems caused by user’s
any fault or carelessness.

- PIP (picture in picture) Function (Only available in 8.8” model)
- Higher Quality
- Controlling PIP function, switching AV source by steering wheel buttons.
- Easier operation with new remote control.
- Upgraded OSD Menu
- Displaying External AV sources through composite, RGB
- Controlling AV sources (DVD, Navi) by I-DRV – Optional
[PIP – A/V Mode]
[PDP – Rear Camera]
-4-
Main features
* FM Transmitter is not offered from this version!!!

1. Input Spec. (MULTI VIDEO INTERFACE)
-. 1 x Analog R,G,B (Sync on Green)
-. 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 3 x A/V (NTST & PAL) Input.
-. 1 x LCD Input (Car system Input)
2. Output Spec.
-. 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x Audio OUTPUT
-. 1 X LCD OUTPUT(LCD Operation)
-. 4 X Audio Select Output
3. Electric Power Consumption
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12WATT, Max
4. Switching Mode (AV source)
- Possible to skip AV source while switching Mode (AV source) by DIP S/W
(Refer to the DIP S/W page)
- By Remote control
-By Toggle Switch (Option)
- By button on the steering wheel in the car via CAN
-5-
Main Spec.

DISPLAY
(CAR MAIN BOARD)
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS In
(Rear camera)
Car Screen Input
A/V 2
A/V 3 VIDEO
CIRCUIT VIDEO MUX
MCU
Power Input
(+8VDC ~ +24VDC)
POWER
CIRCUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote
(OSD keypad) Switch for source toggle
OEM Navi Button (Can Interface)
FMTX
Car installation OEM
LCD
(Video out 2
Audio L, R1)
-6-
System Composition

154mm * 94mm * 20mm 154mm
94mm
20mm
-7-
Outline Dimension

LED DIP S/W LCD-IN LCD-OUT
POWER/CAN MODE A/V(IN/OUT)
Remote
(KEYPAD)
RGB(IN)
-8-
External Appearance

LED
LCD-IN
LCD-OUT DIP S/W
Remote
(KEYPAD)
A/V (IN/OUT)
MODE
POWER RGB(IN)
-9-
External Appearance

①R DATA (RED)
②G DATA (GREEN)
③B DATA (BLUE)
④SYNC (WHITE)
⑤GND (BLACK)
⑥NAVI IR (WHITE)
⑦DVD IR (BLACK)
*RGB-IN Connect
①ACC (RED)
②GND (BLACK)
③REAR-C (GREY)
④SAFE (VIOLET)
⑤CAN(H) (WHITE)
⑥CAN(L) (YELLOW)
⑦NAVI SEL (BLUE)
⑧AV1-SEL (GREEN)
⑨AV2-SEL (BROWN)
⑩AV3-SEL (ORANGE)
*Power Connect
A/V (IN/OUT)
MODE
POWER
①②③④ ⑤⑥⑦⑧⑨⑩
①②④⑤ ⑦
③⑥
RGB(IN)
-10-
Connector Pin Assignment
*12V Select
(Wire no.7~10 of the
Power cable)
Ex) When RGB is selected
12V comes out from
wire no. 7

-11-
FILTER
& FUSE BOX
* Power Cable
AV3-Sel
AV2-Sel
AV1-Sel
NAVI Sel
CAN(L)
CAN(H)
SAFE
REAR-C
ACC
GND
1m
Connector Pin Assignment

#PIN FUNCTION DIP S/W Selection
1RGBINPUTMUTE
ON : Skipping RGB Mode
OFF : RGB Display
2 A/V 1 MUTE ON : Skipping A/V 1
OFF : A/V1 Display
3 A/V 2 MUTE ON : Skipping A/V 2
OFF : A/V2 Display
4 A/V 3 MUTE ON : Skipping A/V 3
OFF : A/V3 Display
5 To select monitor size ON : 6.5” LCD Setting (Possible to use BMW 1 series)
OFF : 8.8” LCD Setting
6 Type of monitor
ON : Siemens setting (only when to turn on the 5th pin)
OFF : Alpine setting (only when to turn on the 5th pin)
ON : 2009model’s 3series(only when to turn off the 5th pin)
OFF : 8.8” Setting
7 Rear Mode ON : External Rear Camera
OFF : OEM Rear Camera
8N.C
※ON : DOWN, OFF : UP
-12-
DIP SW Setting

5 6
E60 8.8” OFF OFF
E60 Alpine 6.5” ON OFF
E60 Siemens 6.5” ON ON
New 3 Series in 2009 OFF ON
#PIN
모니터 지원방식
※DIP S/W Use Example
[BMW E60-6.5” Alpine]
-. Use Input Mode : A/V3(DVD), Navigation (RGB)
-. Rear Camera : When to be installed on CVBS 4
▷DIP S/W : 1 ÆOFF
▷DIP S/W : 2,3 ÆON
(INPUT MODE SKIP)
▷DIP S/W : 4 ÆOFF (enable A/V3)
▷DIP S/W : 5 ÆON (6.5” Alpine)
▷DIP S/W : 6 ÆOFF
▷DIP S/W : 7 ÆON (enable CVBS4)
▷DIP S/W : 8 ÆOFF
[E60 8.8”]
[E60 Alpine 6.5”]
[E60 Siemens 6.5”]
[2009년형 3시리즈]
-13-
DIP SW Setting

How to use Remote
POWER : Interface operation
PIP : Short press – Activating PIP (Picture in Picture)
Long press – Switching AV source
MENU : Activating OSD Menu
OK : Select
▲: UP
▼: DOWN
◀: LEFT
▶: RIGHT
*FACTORY MODE (Interface setting)
: Operated with pressing ▲-> ▼-> ▲->MENU
buttons of the remote in sequence
Dimension : 85 * 40 * 8 (mm)
-14-

-OSD(On Screen Display)
· Analog RGB Mode · Video Mode
IMAGE Menu
- BRIGHTNESS
- CONTRAST
-SHARPNESS
- SATURATION
-HUE
-USER IMAGE
-15-

OSD(On Screen Display)
· Analog RGB Mode · Video Mode
OSD Menu
-LANGUAGE : (Only available for English)
-TRANSPARENT
-H_POSITION : Move the position of AV sources to Left, Right
-V_POSITION : Move the position of AV sources to Up, Down
-16-

OSD(On Screen Display)
· Analog RGB Mode · Video Mode
UTIL Menu
-FACTORY RESET : Initializing of all values of OSD setting
(Impossible to reset of screen position, only possible for functions in OSD)
-17-

OSD(On Screen Display)
Factory Mode
-PARK – PARK ENABLE
- H-POSITION
- V-POSITION
-UTIL – CAR MODEL : Selection of using this interface for E60, E70.
- FACTORY RESET : Initializing
· Factory Mode
- Factory mode is activated by pressing ▲→▼→▲→MENU buttons of the remote.
-18-

①①When the car gear is in reverse,
Enter to the Factory mode by
▲→▼→▲→MENU button of
remote. Then, the left image will
be displayed on the screen.
②②Set “PARK ENABLE” to “ON” on
the park mode, then the line will
be displayed like the pic no. 2
* If you would like to remove this
line, just select “Off” on the
above process.
Factory Default : DISPLAY - DISABLE
-19-
How to use parking guide line

③③Can move the line with H-Position
on the factory mode.
④④Can move the line with V-Position
on the factory mode.
-20-
How to use parking guide line