Bodet Sigma Mod Instructions and recipes

1
Upon receipt, always check the product for damage during shipment. If any is found, you may le a damage
claim with the carrier.
Sigma Mod master clock
SIGMA
Installation and start-up instructions
The document concerns the following products :
907451 Wall Sigma Mod - 110/230V
907452 Wall Sigma Mod - 24V
907453 Rack Sigma Mod - 110/230V
907454 Rack Sigma Mod - 24V
907456 Rack Sigma Mod - 36/72V
BODET SA
BP30001
49340 TREMENTINES
Tél: [phone]
Fax: [phone]
Ref : 606554 ZB
www.bodet-time.com

2
Table of contents
1) General 5
2) Safety rules 6
PROTECTIONS : 6
3) Description 8
4) Installation 9
4.1 Mechanical installation 9
4.2 Electrical connections 10
5) Installation examples 13
5.1 Setting a 24V time distribution 13
5.2 Setting a DHF time distribution 13
5.3 Programming a RHF circuit 14
5.4 Install an option board 15
5.5 Set a 24V TBT output 15
6) Keypad: Key functions 16
7) Main menu programming 18
7.1 Standby state 18
7.2 User menu 18
7.3 USB loading and backup 19
7.4 Adding DHF receivers 20
7.5 Bank holidays 21
7.6 Access code 21
7.7 Time and date 22
7.8 Dynamic radio 23
7.9 Language 23
7.10 Version 23
8) Programming the circuits 24
8.1 Viewing the circuits 25
8.2 Programming the circuits 25
8.2.1 Add a program step 27
8.2.2 Delete a program step 27
8.2.3 Modify a program step 28
8.3 Deleting a program 28
8.4 Viewing the status of a circuit 28
9) Manual testing of circuits 29

3
10) Programming in Holidays and Special Day mode 30
11) Technician menu programming 32
11.1 Time synchronisation menu 33
11.1.1 Programmable time changeover 34
11.1.2 Setting the time base 35
11.2 Time output management menu 36
11.3 IP conguration menu 38
11.4 Relay setting menu 39
11.5 RHF circuit function setting menu 40
11.6 Function setting menu 41
11.7 “Delete all programming” menu 42
11.8 CPU software download menu 43
11.9 Factory setting restoration menu 44
12) Priority of execution of programs 45
13) Alarm messages 46
14) Options 48
14.1 Mechanical installation 48
14.2 Option board with 3 AFNOR outputs 49
14.3 Option board with 2 ASCII outputs 50
14.4 Option board impulse // 52
14.5 Option board with 2 serial outputs (24VDC power supply) 53
14.6 Option board with 2 serial outputs (48VDC power supply) 54
14.7 relay option board 56
14.8 Option board with AFNOR input 57
14.9 Three inputs option card 58
15) Technical characteristics 59
Appendix I : NTP programming 61
IP function programming 61
IP network conguration and protocols supported : 63
16 ) What to do if ...? Check that … 64

4
SIGMA M
Installation and start-up instructions

5
1) General
The Sigma is a master clock which can be used to control receiver clocks and
heating circuits, lighting, ringing, access at the doors of the building, etc.
The SIGMA has functions which can be programmed from the technician
menu.
On rst installation, it is essential to program the technician menu (see
page 32) before the customer menu.
It is also essential when installing the SIGMA to program the technician
functions in the order in which they appear in the menu.
This product must be installed in a residential, commercial or light industry
environment.
Bodet declines all responsibility in the event of an accident resulting from use
not in accordance with the recommendations of this manual.
CAUTION :
Any modication on the product renders the guarantee null and void.
Checking the equipment:
One SIGMA master clock.
One USB key,
One CD containing the PC software.
The CD supplied with your unit contains a program allowing you to carry out
the programming. The programming can thus be carried out simply on a PC
and transferred via the USB port of the Sigma (see “USB loading and backup”,
page 19).
To verify the model of the master clock,
press the key. SIGMA MOD

6
2) Safety rules
• Installation and maintenance of this equipment should only be carried
out by qualied personnel.
• If the SIGMA is connected to the 230 V mains power supply, its installation
must comply with the European standard IEC 364 (NFC 15.100 for France).
PROTECTIONS :
• 110-230V version: the mains supply for this device must include a neutral
phase circuit breaker of maximum 6 A C curve, rapidly accessible upstream
from the supply.
• 24V DC version: the SELV 24 V power supply for this device must include a
protection of maximum 6 A.
• 36-72V DC version: the SELV 36-72 V power supply (according to NFC 15-
100) for this device must include a protection of maximum 6 A.
• For the relay circuits, add protections with circuit beakers of maximum 4
A. Indicate on the labels the location of these protections.
• The circuit breaker must be switched off during maintenance operation.
Refer to labels in the product.
• All cables must be attached either to the wall (wall-mounted version) or to
the frame of the cabinet (Rack version) before being connected to the various
terminals strips, to prevent any pulling on these terminal strips. In addition, the
wires of each terminal strips must be attached to each other to maintain the
various isolations if an initial fault occurs.
• The time distribution cables must not run alongside high power mains
cables (to avoid interference with communication between the SIGMA and the
clocks).
• The SIGMA must be attached (to the wall or on its support) before being
switched on.

7
• The “RACK” models must be mounted in 19” cabinet. These components
will provide mechanical, electrical and re protection (only the front panel may
remain accessible).
• IMPORTANT: before any installation, refer to the “technical
characteristics” paragraph.
• Think of making a backup of your programming on the USB key. In case of
incident (breakdown, thunderstorm…), you will just have to restore the backup
to start the time distribution again.
Caution :
• In case of replacement of the CR2032
battery, it is IMPERATIVE to respect the
polarity following the opposite indications.
• There is risk of explosion if the battery is
replaced by a battery of incorrect type.
• Dispose of used batteries according to the
instructions of the manufacturer.
-
+

8
3) Description
Wall box
A) LCD screen
B) Keypad (see page 16)
C) Alarm indicator light (red
LED)
D) Mains indicator light (green
LED)
E) USB connector
F) Relay output terminal strips
19” Rack
E
A
C
D
B
D
C
AE B

9
4) Installation
4.1 Mechanical installation
Choose a room with low temperature variations
away from any source of electrical interference
(contactors, motors, etc.).
WALL-MOUNTED version: Unscrew the 2
screws on the front, remove the cover (for the
lower cover, press on the 2 clips (N) and slide
it upwards). Disconnect the at jumpers (Q) (be
careful to connect them the same way round
on reassembly) and attach the SIGMA to the
wall. When your unit is in place, remove the
protective lm on the keypad.
RACK version: Install the rack in its slot in an
electrical bay or cabinet.
QN

10
4.2 Electrical connections
Connect the cables (mains power supply, impulse line or AFNOR output and
radio synchronisation input, depending on the model) to the corresponding
terminal strips as shown in the gure below.
(*) See page 33, the “Time outputs” menu to set this output (Pulse minute,
½ minute, second 24V or power TBT 24VDC 1A).
(**) Power supply depending on the version of SIGMA master clock.
Meaning of status of LEDs on RJ45 connector :
- The green LED reects network activity.
- The yellow LED indicates the speed of the network:
off=10 Mbps on=100 Mbps.
RACK version: The mains power supply, impulse line and AFNOR output and
radio synchronisation input terminal strips are directly accessible at the rear of
the Rack slide-in unit.
(**) 110 to
230VAC or
24VDC
or
36/72VDC
Circuit C1
Circuit C2 Circuit C3
GPS input
DCF
radio input
(*) Minute, ½ mn or
second 24V, or SR2-59
Afnor output
DHF output
External input
See the limit
characteristics of
these circuits on
page 59
Attach the wires to each other, near
the terminal strips.
IP connection