Bodet Profil 960 Series User manual

1
Profil 960 Clock indoor
Horloge Profil 960 intérieure
ANALOGUE CLOCKS indoor
HORLOGES ANALOGIQUES intérieures
NTP Receiver
Réceptrice NTP
Installation and operation manual
Manuel d’installation et de mise en service
When receiving goods please check nothing is broken otherwise make a claim near shipping company.
S’assurer à réception que le produit n’a pas été endommagé durant le transport pour réserve au transporteur.
Réf : 607924 E
www.bodet-time.com
BODET Time & Sport
1, rue du Général de Gaulle
49340 TREMENTINES I France
Tél. support France: 02.41.71.72.99
Tel. support (intl): [phone]

2
EN
Table of contents
I - Initial checks 4
1.1 Unpacking the clock 4
1.2 Cleaning 4
1.3 Pre-requisit 4
II - Installation 5
2.1 Pre-requisit 5
2.2 Single sided (SF) clock 5
III - Power supply 6
IV - Setup and initial time setting 6
V- Factory configuration 6
VI - Web interface - Use 7
6.1 Home 7
6.2 Network configuration 8
6.3 Time and synchronisation configuration 9
6.4 Alarm configuration 11
6.5 System 13
VII - Technical characteristics 14
VIII - What to do if…? ... Check. 15

3
FR
Table des matières
I- Vérification initiale 16
1.1 Déballage de l’horloge 16
1.2 Nettoyage 16
1.3 Pré-requis 16
II - Installation 17
2.1 Pré-requis 17
2.2 Horloge Simple Face (SF) 17
III - Alimentation 18
IV - Mise en service et mise à l’heure 18
V- Configuration réseau 18
VI - Serveur web - Utilisation 19
6.1 Accueil 19
6.2 Configuration réseau 19
6.3 Configuration de l’heure et de la synchronisation 21
6.4 Configuration des alarmes 23
6.5 Système 25
VII - Caractéristiques techniques 26
VIII - Que faire si...? ...Vérifier. 27

4
I - Initial checks
Thank you for choosing a BODET clock.
This product has been carefully designed for your satisfaction, using ISO 9001 quality processes.
We recommend that you read this manual carefully before handling the clock.
Retain this manual for reference throughout the operating life of your clock.
Using the clock in a manner not according to these instructions may cause irreversible
damage to the clock and invalidate the product guarantee.
These instructions relate to «NTP» models. For other models please see the corresponding
instructions.
1.1 Unpacking the clock
Carefully unpack the clock and check the contents of the package. This should include:
– the Profil 960 clock and this manual,
– an antistatic cleaning kit,
Version: inside the clock is a product label stating the version of the clock:
NTP = the clock is a receiver controlled by a master clock or an NTP server.
1.2 Cleaning
Use an antistatic product identical to that supplied. Never use alcohol, acetone or other solvents
which may damage your clock’s casing or glass.
1.3 Pre-requisit
For the commisioning of the clocks you must install «BODET Detect». This software is available
on BODET web site www.bodet-time.com as a free download.
Note: the Ethernet network connection to which the Bodet clock is connected must be PoE, the
power being supplied by a PoE switch or a PoE injector.
Bodet recommends the following devices:
■PoE injectors: Zyxel, Tp link, D-Link, HP, Cisco, Axis, ITE Power Supply, PhiHong, Abus,
Globtek.
■PoE switches: D-Link, HP, Planet, Zyxel, Cisco, NetGear, PhiHong.
EN

5
II - Installation
2.1 Pre-requisit
Choose a location where to install the clock, preferably away from sources of electrical interference,
such as transformers.
Installation and maintenance of this equipment must be carried out by qualified personnel.
The clock is connected to the Ethernet (PoE) data network. The equipment must be installed in
compliance with standard 802.3af, class 3.
2.2 Single sided (SF) clock / ref.: 933D11, 933D21, 933D31
1) Drill the support to the required dimensions.
2) Place the 2 screws Ø6 (1) with their washers.
3) If necessary, carry out the various connections (see chapter power supply and setup and initial
time setting).
4) Hang the clock and screw it with a size 10 at key.
EN

6
III - Power supply
NTP clocks are synchronized and powered by the Ethernet network (PoE).
IV - Setup and initial time setting
1) Connect the Ethernet network on the RJ45 connector (A).
■Ethernet cable category: 5 minimum or 6.
The type of synchronisation will have to be programmed in pages webserver of the clock. Find
the MAC address (B) which will be useful during the detection of the clock on the software Bodet
Detect to reappoint it.
2) Meaning of LEDs indicators on the RJ45 connector :
■The green LED is on when the clock is powered on.
■The yellow LED is blinking once per second when the clock is synchronised.
■ The yellow LED is blinking fast for 5 s then switching o󰀨 for 3s when the clock is not
synchronised or no more synchronised for 1 hour.
■The yellow LED is permanently switched on when you make a localization of the clock since
the software Bodet Detect.
V- Factory configuration
The default conguration is as follows:
■ IP conguration by DHCP.
■Time zone: EUR.
■Multicast synchronisation.
■Synchronisation adress: 239.192.54.1.
A reminder of this conguration is printed on the back of the product.
The full factory conguration is as follows:
■Clock name: «BODET-@MAC».
■ IP conguration by DHCP.
■Time zone: EUR.
■Multicast synchronisation.
■Synchronisation address: 239.192.54.1.
■Pool period for unicast synchronisation: 15 mins.
■SNMP disabled.
■Trap type: V2C.
■Temperature alarm threshold: –5°C to +55°C.
■Trap status sending interval: 24H.
■No password.
EN

7
EN
VI - Web interface - Use
There are two ways to access the web interface:
1/ Open your web browser and enter the IP address of the clock in the address bar.
2/ Using the «BODET Detect», click on the Web browser button to open the web interface (refer to
software instructions, 607548).
The BODET Detect software lets you:
- detect all the clocks present on the network,
- individually set the parameter of each clock or copy the parameter of one clock toward a group
of clocks,
- update the clock software,
- check the clock status
- access the download of the MIB files.
6.1 Home
The home page presented by the product embedded web server provides a general information
on the product.
The information is displayed as follows:
- Product: product type.
- Name: user-defined clock name.
- Synchro: status of the synchronisation (Strat 4 indicates that the clock is at the 4th level from the
synchronisation source) + adress multicast of broadcasting.
- Local Date : current date.
- Local Time : current time.

8
EN
6.2 Network configuration
This page is for setting the clock’s network configuration. The warning reminds you that the
product could lose its connection to the network if incorrect parameters are set (see III - Factory
configuration, page 16)
The information displayed is described below:
- MAC Address: this is the clock’s MAC address. This address is unique to each device. This
number is given on a label on the back of Bodet clock.
- Name: user-defined clock name.
- Enable DHCP checkbox: if checked, the device’s network IP settings will be configured
automatically (in the case where a DHCP server is present on the network).
If this box is unchecked, the following settings are available:
- IP Address: manually sets the clock’s IP address. (required if not DHCP server).
- Subnet Mask: the subnet mask associates a clock with the local network.
- Gateway: the gateway can be used to connect the clock to two data networks.
- DNS Address: this can be used to associate a clock name with an IP address. This avoids
having to enter an IP address in the browser: a user-defined name can be used instead.Example:
www.bodet.com is simpler to remember than 172.17.10.88.
The Save and Reboot button saves your configuration and reboots the clock.

9
EN
6.3 Time and synchronisation configuration
The Time Configuration page is divided into two parts. One is used to set the time zone, the other
to set the synchronisation mode.
The information displayed is described below:
- Time zone : the drop-down menu can be used to select the appropriate time zone (summer/
winter time changes are automatically managed according to the selected time zone).
When «PROG» is selected in the drop down menu, this feature allows you to set the time, month,
or day fixed rank changes of seasons:

10
EN
- NTP Mode: one of three modes may be selected:
o Unicast: In Address IP 1, enter the IP address of the NTP server. In this case it is the clock that
calls the NTP server.
It is also possible to set up redundancy (if the first server does not respond, the second is queried,
and so on): for this purpose up to 5 server addresses may be entered.
The Periodicity field sets the frequency with which the clock queries the configured NTP servers.
o Multicast: In this case, the NTP server broadcast the time on the multicast address that
was that given to it. The multicast address of the clients (reveivers) must be the same that the
one on which the server broadcasts.
By default, the Bodet products transmit or receive using the multicast address: 239.192.54.1
The multicast addresses are included between 224.0.0.0 and 239.255.255.255.
o By DHCP:Same mode as Unicast except that the addresses of the NTP servers are
gatherautomatically via the DHCP server (option 42 on the DHCP server).
The checkbox «continue to display time after synchronisation failure» is used to define the
behavior of the AFNOR output after synchronisation NTP failure during 48 hours :
■ The checkbox «continue to display time after synchronisation failure» in OFF, stop
AFNOR emission (configuration by default).
■ The checkbox «continue to display time after synchronisation failure» in ON, the clock
continues to broadcast AFNOR.
The Save buttons save the configuration data entered.