Body Champ BF 2700 User manual

OWNER’S MANUAL
* This item is for consumer use only and it is not meant for commercial use.
BF 2700
Pro Cycle Trainer

This page intentionally left blank

General Information
Page 1
Warranty
Body Flex Sports warrants your product for
a period of 1 year for the frame and 90 days
on all parts if the item is used for the intended
purpose, properly maintained and not used
commercially. Any alterations or incorrect
assembly of the product will void this warranty.
Proof of purchase must be presented for any
warranty validation (no exceptions). This
warranty applies to the original purchaser only
and is not transferable.
This warranty does not cover abuse or defects
caused during use, storage or assembly.
During the warranty period, Body Flex Sports
reserves the right to:
a). provide replacement parts to the
purchaser in an effort to repair the item.
b). repair the product returned to our
warehouse (at the purchaser’s cost).
c). replace the product if neither of the two
previously mentioned actions effect repair.
This warranty does not cover normal wear and
tear on upholstery.
Questions
If you have any questions concerning the
assembly of your item or if any parts are
missing, please DO NOT RETURN THE
ITEM TO THE STORE OR CONTACT THE
RETAILER. Our dedicated customer service
staff can help you with any questions you may
have regarding the assembly of this unit and
can also mail you replacement parts.
Customer Support
Customer Support is open 9:00 a.m. to 5:00
p.m. (Pacific Time) Monday through Friday.
Please contact us by any of the following
means.
Body Flex Sports, Inc.
21717 Ferrero Parkway, Walnut, CA 91789
Telephone: (888) 266 - 6789
Fax: (909) 598 - 6707
Email: info@bodyflexsports.com
Safety
Before you undertake any exercise program,
please be sure to consult with your doctor.
Frequent strenuous exercise should be
approved by your doctor and proper use
of your product is essential. Please read
this manual carefully before commencing
the assembly of your product or starting to
exercise.
• Please keep all children away from this item
when in use. Do not allow children to climb or
play on them when they are not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there
is at least 3 feet of free space in all directions
around your product while you are exercising.
• Regularly check to see that all nuts, bolts and
fittings are securely tightened. Periodically
check all moving parts for obvious signs of
wear or damage.
• Clean only with a damp cloth, do not use
solvent cleaners. If you are in any doubt, do
not use your product; contact CUSTOMER
SUPPORT.
• Before use, always ensure that your product
is positioned on a solid, flat surface. If
necessary, use a rubber mat underneath to
reduce the possibility of slipping.
• Always wear appropriate clothing and
footwear such as training shoes when
exercising. Do not wear loose clothing that
could become caught in moving parts during
exercise.
• Do not use this unit if it is not functioning
properly or if it is not fully assembled.
• Do not use this unit for commercial purposes.
Storage and Use
Your product is intended for use in clean
dry conditions. You should avoid storage in
excessively cold or damp places as this may
lead to corrosion and other related problems.
Weight Limit
Your product is suitable for users weighing:
250 pounds or less.
• Before use, you must read and understand all
instructions & warnings stated in this Owner’s
Manual as well as posted on the equipment.
• It is the facility owner’s responsibility to properly
instruct users on the proper operation of the
equipment and to warn them of the potential
hazards.
• If at any time during exercise you feel faint, dizzy
or experience pain, stop and consult your
physician.
Assembling Tools
- Ruler with both metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver
BF 

Hardware List
The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these
items. Please note some of this hardware is already pre-assembled on the machine. Do not be alarmed if you
see parts on this page that are not included in your hardware packet
Bolts
Washers
Others
#01. Bolt (M8x50x20xS6 mm)
[4 Pieces]
#52. Screw (M4x12xφ6 mm)
[2 Pieces] Pre-assembled
#02. Washer (d8xφ16x1.5 mm)
[4 Pieces]
#20. Washer (d10xφ40x4 mm)
[1 Piece]
#51. Washer (d4xφ12x1 mm)
[2 Pieces] Pre-assembled
#11. Knob Bolt (M16x1.5x15xφ49 mm)
[2 Pieces] Pre-assembled
#21. L Shaper Bolt (M10x25 mm)
[1 Piece]
#25. L Shaper Bolt (M16x1.5x18 mm)
[1 Piece]
#48. Tool 1 (S6)
[1 Piece]
#49. Tool 2 (S13-14-15)
[1 Piece]
Page 2
BF 2700

Page 3
Parts Listing
The following parts list describes all of the parts illustrated on the
exploded diagram on the following page. Please note, most of
these parts are already pre-assembled on your unit.
# Description # Description
01 Bolt (M8x50x20xS6 mm) 28 Brack Spacer (φ12xφ9x15 mm)
02 Washer (d8xφ16x1.5 mm) 29 Bolt (M5x12xS4 mm)
03 Front Stabilizer 30 Brack Bracket (t3x20x138.4 mm)
04L/R Left/Right End Cap for Front Stabilizer 31 Nut (t5x12x12 mm)
05 Washer (d5xφ10x1 mm) 32 Spring (φ1.5xφ12x21xN6 mm)
06 Screw (ST4.2x25xφ8 mm) 33 Brack Spacer (13x13x11.5 mm)
07 Rear Stabilizer 34 Wire Cap (φ8 mm)
08 End Cap for Rear Stabilizer 35 Nut (M6xH5xS10 mm)
09 Main Frame 36 Screw (M5x30xφ8 mm)
10L/R Left/Right Pedal 37 Washer (d5xφ10x1 mm)
11 Knob Bolt (M16x1.5x15xφ49 mm) 38 Nylon Nut (M5xH5.5xS10 mm)
12 Sleeve (PT70x30xPT60x20xL145x10 mm) 39 Brack Sprin Bracket (t1.2x23x122 mm)
13 End Cap (PT60x20x30 mm) 40 Washer (d6xφ12x1.2 mm)
14 Horizontal Seat Bar 41 Hex Bolt (M6x12xS10 mm)
15 Seat 42 Brack Cap (35x24x2 mm)
16 Sleeve (PT70x30xPT60x20xL67x9 mm) 43 Brack Spring (φ2xφ24xφ13x15xN5 mm)
17 Seat Post 44 Brack Base (110x27x30 mm)
18 Handle Bar 45 Friction Pad (110x30x6 mm)
19 Front Post 46 Nylon Nut (M6xH6xS10 mm)
20 Washer (d10xφ40x4 mm) 47 Tension Control Knob (M8xH30xφ40 mm)
21 L Shaper Bolt (M10x25 mm) 48 Tool 1 (S6)
22 Sleeve (F38x38xF30x30xL120 mm) 49 Tool 2 (S13-14-15)
23 Bushing (φ27x1.5xφ24x16 mm) 50 Water Bottle Holder
24 Nut (φ35x3xM30x1.5x8xM16x1.5 mm) 51 Washer (d4xφ12x1 mm)
25 L Shaper Bolt (M16x1.5x18 mm) 52 Screw (M4x12xφ6 mm)
26 Foam Grip (φ23x3x460 mm) 53L/R Crank
27 Tension Control (φ8x189 mm)
BF 2700
54 Seal

Page 4
The following diagram is provided to help you familiarize yourself with the parts and
hardware that will be used during the assembly process. Please note that not all of the
parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please continue to the next
page to begin the assembly process and use this page only as a reference guide for
parts and hardware.
Exploded Diagram
BF 2700

Page 5
Bolts
Washers
#01. Bolt (M8x50x20xS6 mm)
[4 Pieces]
#02. Washer (d8xφ16x1.5 mm)
[4 Pieces]
A s s e m b l y S t e p 1 Hardware & Tool Required
BF 2700
Front & Rear Stabilizer Assembly
With the help of an assistant, attach the Front Stabilizer
(#03) to bracket at the front of Main Frame (#09). Insert two
Bolts (#01) through two Washers (#02), the Front Stabilizer
(#03) followed by the front Main Frame (#09). Secure them
together by tightening the Bolts (#01).
Now attach the Rear Stabilizer (#07) to the bracket at rear
of Main Frame (#09). Insert two Bolts (#01) through two
Washers (#02), the Rear Stabilizer (#07) followed by the
front Main Frame (#09). Secure them together by tightening
the Bolts (#01).
NOTE:
If labels designating the Left/Right Pedal
are not present, please check pedals
closely for embossed “L”/ “R” letter marks.
These will be “L” / “R” letters that
are raised
on the pedal material.
Pedal Assembly
Secure the Left Pedal (#10L) to the Left Crank (#53L) by
turning the bolt head on the Left Pedal (#10L) COUNTER
-CLOCKWISE.
Secure the Right Pedal (10R) to the Right Crank (#53R) by
turning the bolt head on the Right Pedal (#10R) CLOCKWISE.
Please Note that the Front Stabilizer (#03) has roller
wheels that spin for ease of relocating the unit and the
Rear Stabilizer (#07) has height adjustable caps
for leveling of the unit.
Roller Wheels
(front of caps)
Height Adjustable Caps
(bottom of caps w/
side adjustment dials)
55
40
1 2 3 4
55
40 1 2 3 4
STEP3:
Assembly Instructions

BF 2700 Page 6
Hardware & Tool Required
Washers
Others
#20. Washer (d10xφ40x4 mm)
[1 Piece]
#21. L Shaper Bolt (M10x25 mm)
[1 Piece]
#25. L Shaper Bolt (M16x1.5x18 mm)
[1 Piece]
A s s e m b l y S t e p 2
Handle Bar Assembly
Attach the Handle Bar (#18) to the Front Post (#19) and secure them
together by inserting one L Shaper Bolt (#21) through one Washer (#20)
then through the hole on the Front Post (#19) and the Handle Bar (#18).
Once the Handle Bar (#18) is proberly secured to the Front Post (#19),
insert the Front Post (#19) into the Main Frame (#09) with the Handle
Bar (#18) facing outwards as illustrated. Secure the Front Post (#19) to
the Main Frame (#09) using the L Shaper Bolt (#25).
55
40
1 2 3 4
55
40 1 2 3 4
STEP3:
Assembly Instructions

Page 7
Hardware & Tool Required
Bolts
Washers
Others
#52. Screw (M4x12xφ6 mm)
[2 Pieces]
#51. Washer (d4xφ12x1 mm)
[2 Pieces]
#11. Knob Bolt (M16x1.5x15xφ49 mm)
[2 Pieces]
The assembly process is now complete However,
for your own safety, please make sure to read this
entire manual which includes safety instructions and
warnings as well as any safety/warning labels located
on the product before use.
Do not remove the Seat (#15) for any
reason after you have installed it.
Exercising on this unit without the Seat
(#15) can result in SERIOUS INJURY.
Ensure the seat is locked in place by
tightening the two knobs prior to use.
W A R N I N G
Spring Knob Operation
Turn Knob Bolt (#11) counter-clockwise
three times.
Pull Knob Bolt (#11) outward and adjust
Seat Post (#17) simultaneously.
Push Knob Bolt (#11) back inward until
it clicks and then tighten it by turning
clockwise.
BF 2700
Seat Post Assembly
Attach the Horizontal Seat Bar (#14) to the Seat Post (#17)
with the single point of the seat (#15) pointing toward the
front of the unit as shown in the diagram. Secure by locking
the Knob Bolt (#11).
Attach the Seat Post (#17) onto the mouth of the post that is
protruding from the Main Frame (#09) down a minimum of 4
inches to engage the lowest hole. Please ensure that the hole
on the Seat Post (#17) facing the same side as the Knob
Bolt (#11) so it can be aligned and full engage through the
lowest corresponding hole on the Main Frame (#09) post and
fully through (at minimum) the lowest the hole located on the
Seat Post (#17). Please refer to the illustration.
You may adjust the Seat (#15) to the height most comfortable
for you after complete assembly. Please always check to
ensure a hole has been fully engaged when you secure and
tighten the Knob Bolt (#11).
Water Bottle Holder Assembly
Remove the two Screws (#52) and two Washers (#51) that
are pre-installed on the Main Frame (#09) as illustrated and
set them aside.
Attach the Water Bottle Holder (#50) to the Main Frame
(#09) and secure them together by inserting two Screws
(#52) through two Washers (#51) then through the Main
Frame (#09) as illustrated.
The two Knob Bolts (#11) are pre-assembled on the Seat
Post (#17) and Main Frame (#09).
A s s e m b l y S t e p 3
55
40
1 2 3 4
55
40 1 2 3 4
STEP3:
Assembly Instructions

Assembly Instructions
R e v e r s i b l e M o v e m e n t
Forward pedaling emphasizes your quadricep muscles (front thighs), while backward pedaling emphasizes your hamstrings
(back thighs). The Pro Cycle Trainer allows you to make your workout less fatiguing, more fun, and more effective with forward
and backward movement functionality.
P e d a l & S p e e d S a f e t y
The Pro Cycle Trainer features an incredibly smooth flywheel for seamless workout movement. However, please note that the
flywheel and pedals can become safety hazards when extreme speed and momentum are used. We do not advise that you stand
and pedal on the bike simultaneously. If you prefer a workout session with greater speed and momentum, please remove the
straps of the Pedals (10L/R) to avoid your ankles and/or feet from getting caught by the momentum. If straps are removed, please
remember to place them back onto the Pedals (10L/R) after your workout session to avoid injury to yourself and those around you.
Always wait for the flywheel, crank, and pedals to come to a complete stop before you dismount the bike to avoid serious injury.
A.) Adjusting the Tension:
Increasing or decreasing the tension allows you to add variety to your workout sessions by adjusting
the resistance level of the bike.
To increase tension and increase resistance (requiring more strength to pedal), turn the Tension
Control Knob (#47) to the right.
To decrease tension and increase resistance (requiring less strength to pedla), turn the Tension
Control Knob (#47) to the left.
B.) Using the Emergency Brake Function:
The same knob that allows you to adjust the tension of the bike also doubles as the Emergency
Brake. Use this safety feature in any situation where you would need to get off the bike and/or
stop the bike’s flywheel.
To use the Emergency Brake function in any situation you would need it in, firmly press down
on the Tension Control Knob (#47). .
Brake Uses Guide
AB
Page 8BF 2700

Safety & Maintenance
Page 9
• Make sure all nuts, bolts, and screws are tightened prior to use.
• Be sure that all adjustment locking devices and safety devices are properly engaged prior to use!
• Never over-tighten the above-mentioned devices and parts to avoid damage to the unit.
• Check for loose parts and components prior to use.
• Check to see if there are any tears or bends in the welding or metal prior to use.
• Extreme care must be taken to not allow your feet, fingers, hair, clothing, and/or any loose items to be
snagged into any portion of the bike when the flywheel is in motion. Failure to follow these instructions
could result in serious injury, including the loss of fingers.
• Always wait for the flywheel, pedals, and cranks (which can gain great momentum during riding) to
come to a complete stop before dismounting the bike to avoid serious injury.
• To avoid rust or corrosion to the flywheel caused by moisture and sweat, we advise wiping and drying
the flywheel and surrounding parts with a dry absorbent towel after each workout session.
• Do not use solvent cleaners. If you are in any doubt, do not use your cleansing product;
contact CUSTOMER SUPPORT.
• When bike is not in use, the resistance should be left loose, NOT tightened down against the flywheel.
You can do this with the easy-to-adjust tension knob. This will ensure longer life of the Friction Belt.
• You can maintain your bike by using certain products. However, be careful not to allow lubricants
to get onto the circumference of the flywheel where the Friction Belt rubs against. This will
prevent the friction mechanism from working properly. Please contact our CUSTOMER SUPPORT
if you have questions regarding the cleaning of your bike.
A d d i t i o n a l S a f e t y
M a i n t e n a n c e & C a r e
BF 2700

Before use, you must read and understand all instructions & warning stated in this Owner's Manual as well as
posted on the equipment.
Warm-Up Instructions
Groin Stretch
1. Sit with your knees flexed
and soles of feet together.
2. Hold your ankles and bend
at your hips (keep your
back straight) as you press
your knees toward the
floor with your elbows.
Hamstring Stretch
1. Sit with your left leg extended and bend your right
leg at the knee as you place the sole of your right foot
against the inner thigh of your extended leg.
2. Flex the foot of your extended leg (toes pointed
toward ceiling) and gently bend forward from your
hips; keep your back straight.
3. Reach your hands on your extended leg as far as pos-
sible and then switch legs and repeat.
Trunk Twister
1. Sit with your leg extended and
bend your right knee as you cross
your right leg over your left leg.
Your right foot should be flat on the
floor alongside your left knee.
2. Place your left arm on the outside
of your right leg and pull against
that leg while twisting your trunk
as far as possible to the right. Place
your right hand on the floor behind
your buttocks. Reverse leg posi-
tions and repeat.
Hip Stretch
1. Lie on your back and raise your right leg as you clasp both hands
under the back of the knee. Keep your left leg straight.
2. Gently pull your right leg toward your trunk without raising your
upper body. Switch leg positions and repeat.
The following flexibility exercises are provided to you as a means to prevent injury while you are exercising. A
proper warm-up routine decreases the chance of injuring your muscles while you are exercising. Please take the
time to do these flexibility exercises before and after each time you exercise.
Quadriceps Stretch
1. Stand on your left leg and hold onto
a support with your left hand.
2. Flex your right leg behind you, grasp
your ankle or foot with your right
hand and pull your foot toward your
buttocks. Keep your back straight
and right knee pointed down. Repeat
on the other leg.
BF 2700 Page 10

Trunk Flexion, Prone
1. Assume the depicted position on your hands and knees. Stretch your hands out in front of you and then slowly start to pull
them back in toward your body as you tuck your chin and arch your back upward.
2. Return to the starting position slowly.
Shoulder Stretch
1. Bring your right hand over
your right shoulder to the
upper back and bring your
left hand under your left
shoulder to the upper back.
2. Try to reach your finger-
tips. If you are not able to
reach your fingertips, use
a towel as an extension of
your hands and gently pull
one hand toward the other.
Reverse arm positions and
repeat.
Calf Stretch
1. Place both hands against
a wall to aid your balance.
Press the ball of your left foot
against the wall and keep the
heel of the same foot rested
on the floor (make sure your
left knee is bent).
2. Slowly start to straighten your
left knee and you will feel
the muscles in your left calf
stretch. Switch leg positions
and repeat.
Warm-Up Instructions
Page 11BF 2700

WARNING: SERIOUS INJURIES AND EVEN DEATH CAN OCCUR IF THE PROPER SAFETY PRECAUTIONS ARE NOT FOLLOWED.
The diagram below highlights and reviews many of the important Safety and Warning labels also found
on the unit. Please ensure any user of the unit familiarizes themselves with these Safety and Warning
guidelines before use.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE & REFERENCE.
DO NOT DISCARD.
Page 12BF 2700
DO NOT REMOVE THE
SEAT FOR ANY REASON.
Exercising on this unit
without the seat installed
can result in SERIOUS
INJURY.
Ensure the seat is fully
Ensure the seat is fully
locked in place by tightening
the knobs prior to use.
WARNING
1. NEVER ride bike with excessive speed which can cause momentum making flywheel and pedals difficult
to stop and could result in SERIOUS INJURY; Pedal speed shall be reduced in a controlled manner.
2. This bike does not free-wheel. Spinning pedals may cause SERIOUS INJURY.
3. DO NOT dismount bike until flywheel, cranks, & pedals come to complete stop.
4. ALWAYS ensure the handlebar, seat, nuts, & bolts are all securely fastened before each use of this bike
to prevent SERIOUS INJURY.
5. NEVER operate this bike without the seat properly assembled.
6. READ all safety instructions and warnings in the Owner’s Manual and labels on this unit. The unit shall
only be used after a thorough review of the Owner’s Manual.
7. Please keep all children away from this unit.
8. REPLACE this and any labels on this unit if damaged, illegible, or removed.
9. MAXIMUM WEIGHT CAPACITY: 250 lbs.
W A R N I N G !
!

Proof of purchase
version: 09-16-2014
Model Number BF 2700
BF 2700

Body Flex Sports, Inc. • 21717 Ferrero Parkway, Walnut, CA 91789 • Telephone: (888) 266 - 6789 • Email: info@bodyflexsports.com
Made in China