Body Craft SW-HFT User manual

TF
SWHFT.01.02
TF-
~ 240 Min.
CM
Assembly Instructions
Art. No. SW-HFT
Cable Pull ModuleHFT
L 102 | W 142 | H 208

2HFT

3
Content
1 GENERAL INFORMATION 6
1.1 Technical Data 6
1.2 Personal Safety 7
1.3 Set-Up Place 8
2 ASSEMBLY 9
2.1 General Instructions 9
2.2 Scope of Delivery 10
2.3 Assembly 12
3 STORAGE AND TRANSPORT 22
3.1 General Instructions 22
4 TROUBLESHOOTING, CARE AND MAINTENANCE 23
4.1 General Instructions 23
4.2 Faults and Fault Diagnosis 23
4.3 Maintenance and Inspection Calendar 24
5 DISPOSAL 24
6 RECOMMENDED ACCESSORIES 25
7 ORDERING SPARE PARTS 26
7.1 Serial Number and Model Name 26
7.2 Parts List 27
7.3 Exploded Drawing 29
8 WARRANTY 30
9 CONTACT 32

4HFT
Dear customer,
Thank you for choosing a high-quality equipment of the brand BodyCraft®. BodyCraft® oers sports
and tness equipment for the sophisticated home sport and the equipment of tness studios and
business customers. With BodyCraft® tness equipment, the focus is on what sport is all about:
maximum performance! Therefore, the equipment is developed in close consultation with athletes
and sports scientists. Because athletes know best what makes perfect tness equipment.
Further information can be found at www.sport-tiedje.com.
Legal Notice
Sport-Tiedje GmbH
Europe’s No. 1 for home tness
International Headquarters
Flensburger Straße 55
24837 Schleswig
Germany
Management:
Christian Grau
Sebastian Campmann
Dr. Bernhard Schenkel
No. HRB 1000 SL
Local Court Flensburg
European VAT Number: DE813211547
Disclaimer
©2010 BodyCraft® is a registered brand of the company SportTiedje GmbH. All
rights reserved. Any use of this trademark without the explicit written permission
of Sport-Tiedje is prohibited.
Product and manual are subject to change. Technical data can be changed without
advance notice.
Intended Use
The equipment may only be used for its intended purpose.
The equipment is suitable for home use and semi-professional use (e.g. hospitals, clubs, hotels,
schools, etc.). The equipment is not suitable for commercial or professional use (e.g. tness
studio).

5
ABOUT THIS MANUAL
Please carefully read the entire manual before installation and rst use. The manual will help you to
quickly set up the system and explains how to safely use it. Make sure that all persons exercising with
the equipment (especially children and persons with physical, sensory, mental or motor disabilities)
are informed about this manual and its contents in advance. In case of doubt, responsible persons
must supervise the use of the equipment.
This equipment has been manufactured according to the latest safety knowledge.
As far as possible, potential safety hazards which could cause injury have been
eliminated. Make sure to carefully follow the instructions and that all parts are
securely in place. If required, read through the instructions again to correct any
mistakes.
Please pay close attention to the safety and maintenance instructions given here. The contract
partner cannot be held liable for damage to health, accidents or damage to the equipment when it
is not used in accordance with these instructions.
The following safety instructions may appear in this manual:
࣑ATTENTION
This notice indicates potentially hazardous situations which, if not avoided, may result in
property damage.
⚠CAUTION
This notice indicates potentially hazardous situations which, if not avoided, may result in slight
or minor injuries!
⚠WARNING
This notice indicates potentially hazardous situations which, if not avoided, may result in death
or serious injuries!
⚠DANGER
This notice indicates potentially hazardous situations which, if not avoided, will result in death
or serious injuries!
LNOTICE
This notice indicates further useful information.
Retain these instructions in a safe place for future reference, maintenance or when ordering
replacement parts.

6HFT
1 GENERAL INFORMATION
1.1 Technical Data
Weight and Dimensions
Article weight (gross, incl. packaging): 168.8kg
Package dimensions (L x W x H) approx.:
Box 1: 205cm x 38cm x 16cm
Box 2: 124cm x 60cm x 21cm
Box 3: 27cm x 14 cm x 13cm
Box 4: 28cm x 19cm x 15cm
Set-up dimensions (L x W x H) approx.: 102cm x 142cm x 208cm

7
1.2 Personal Safety
⚠DANGER
+ Before you start using the equipment, you should consult your physician that this type of
exercise is suitable for you from a health perspective. Particularly aected are persons who:
have a hereditary disposition to high blood pressure or heart disease, are over the age of 45,
smoke, have high cholesterol values, are overweight and/or have not exercised regularly in
the past year. If you are under medical treatment that aects your heart rate, medical advice
is absolutely essential.
+ Note that excessive training can seriously endanger your health. Please also note that
heart rate monitoring systems can be inaccurate. If you notice any signs of weakness,
nausea, dizziness, pain, shortness of breath, or other abnormal symptoms, stop exercising
immediately and seek advice from your doctor if necessary.
⚠WARNING
+ This equipment may not be used by children under the age of 14.
+ Children should not be allowed unsupervised access to the equipment.
+ Persons with disabilities must have a medical license and must be under strict observation
when using the equipment.
+ The equipment is strictly for use by one person at a time.
+ If your equipment provides a safety key, the clip of the safety key must be attached to your
clothing before starting your training. In the event of a fall, the EMERGENCY STOP of the
equipment can be initiated.
+ Keep your hands, feet and other body parts, hair, clothing, jewellery and other objects well
clear of moving parts.
+ During use, wear suitable sports clothing rather than loose or baggy clothing.When wearing
sports shoes, make sure they have suitable soles, preferably made of rubber or other non-
slip materials. Shoes with heels, leather soles, studs or spikes are unsuitable. Never exercise
barefoot.
⚠CAUTION
+ If your equipment needs to be connected to the power supply with a mains cable, make
sure that the cable is not a potential tripping hazard.
+ Make sure that nobody is within the range of motion of the equipment during training so as
not to endanger you or other persons.
࣑ATTENTION
+ Do not insert any objects of any kind into the openings of the device.

8HFT
1.3 Set-Up Place
⚠WARNING
+ Do not place the equipment in main corridors or escape routes.
⚠CAUTION
+ Choose a location in which to place the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The training room should be well ventilated during training and not be exposed to any
draughts.
+ Choose the place in which to set up the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The set-up and mounting surface of the equipment should be at, loadable and solid.
࣑ATTENTION
+ The device may only be used in one building, in suciently tempered and dry rooms
(ambient temperatures between 10°C and 35°C). The equipment should not be used
outdoors or in rooms with high humidity (over 70%) like swimming pools.
+ A oor protective mat/equipment underlay can help to protect high-quality oor coverings
(parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight
unevenness.

9
2 ASSEMBLY
2.1 General Instructions
⚠DANGER
+ Do not leave any tools, packaging materials such as foils or small parts lying around,
as otherwise there is a danger of suocation for children. Keep children away from the
equipment during assembly.
⚠WARNING
+ Pay attention to the instructions attached to the equipment in order to reduce the risk of
injuries.
⚠CAUTION
+ Ensure to have sucient room for movement in each direction during assembly.
+ The assembly of the equipment must be carried out by at least two adults. If in doubt, seek
the help of a third technically skilled person.
࣑ATTENTION
+ To prevent damage to the equipment and the oor, assemble the equipment on a mat or
packaging board.
LNOTICE
+ In order to make the assembly as simple as possible, some screws and nuts to be used can
already be pre-assembled.
+ Ideally, assemble the equipment at its later set-up place.

10 HFT
2.2 Scope of Delivery
The scope of delivery consist of the following parts. At the beginning, check whether all parts
and tools belonging to the device are included in the scope of delivery and whether damage has
occurred. In the event of complaints, the contractual partner must be contacted directly.
⚠CAUTION
If parts of the scope of delivery are missing or damaged, the assembly must not be carried out.

(27) Kabel 2x
11

12 HFT
2.3 Assembly
Before assembly, take a close look at the individual assembly steps shown and carry out the assembly
in the order given.
LNOTICE
First loosely screw all parts together and check that they t properly. Tighten the screws using
the tool only when you are instructed to do so.
Step 1: Assemble upright frame
1. Carefully install two End Caps (38) onto each of the Base Frame Legs (1R & 1L).
2. Attach Rear Upright Frame (4) to the Right & Left Base Frame Leg (1R & 1L) using the eight pre-
installed 3/8” Chromed Washers (62) and 3/8” Chromed Nylon Nuts (68).
3. Attach Top Cross Support (8) to Rear Upright Frames (4) using four 3/8” X 2-1/2” Hex Bolts (52),
eight 3/8” Chromed Washers (62), and four 3/8” Chromed Nylon Nuts (68).
4. Attach Bottom Cross Support (9) to the Rear Upright Frames (4) using four 3/8”X 2-1/2”Hex Bolts
(52), eight 3/8” Chromed Washers (62), and four 3/8” Chromed Nylon Nuts (68).

13

14 HFT
Step 2: Assemble top frame
1. Slide Pulley Height Adjusters (15R & 16L) onto the Upright Frames (2R & 3L)
2. Attach Upright Frames (2R & 3L) to the Base Frame Legs (1R & 1L) using four pre-installed 3/8”
Chromed Washers (62), and 3/8” Chromed Nylon Nuts (68).
3. Attach two Rotating Pulley Holders (17) to the Right & Left Pulley Height Adjusters (15R & 16L)
using two 1/2” X 4-1/4” Hex Bolts (49), four 1/2”Washers (61), and two 1/2” Nylon Nuts (67).
࣑ATTENTION
Pay attention to insert the hex bolts (49) from the bottom into the Heigth Adjusters (15R & 16L)
4. Attach Top Frames (6R & 7L) to Rear Uprights (4) using two 3/8”X 4”Black Hex Bolts (51), four 3/8”
Black Washers (63), two 3/8”Black Nylon Nuts (68).
5. Assemble Top Frames (6R & 7L) to Upright Frames (2R & 3L) along with Chin Bar (7) and Pulley
(36) using four 3/8” X 4-1/4” Black Hex Bolts (50), eight 3/8” Black Washers (63), four 3/8” Black
Nylon Nuts (68).
6. Tighten all bolts starting from the bottom.

15

16 HFT
Step 3: Assemble guide rods
1. Insert two Plastic Guide Rod Holders (24) into the outer holes of each of the Base Frame Legs
(1L & 2R).
2. Install two Rubber Donuts (22) on the Guide Rods (5) and insert the two Guide Rods (5) together
with the Stack Spacers (23) into the Plastic Guide Rod Holders (24).
࣑ATTENTION
From 38 weight plates (21) (19 each side), the Stack Spacers (23) must be removed.
3. Assemble Top Plate (19) to the Selector Rod (20) using the Top Plate Bolt (48), tighten.
4. Thread Pulley Block (18) into Selector Rod (20) a minimum of 1/3 of the way (Fig. A).
5. With the guide rods angled slightly (Fig. B), slide the Weight Plates (21) onto the Guide Rods (5)
LHINWEIS
Orient the selector holes toward the inside bottom.
6. Slide the Top Plate (19) assembly onto the Guide Rods (5), running the Selector Rod (20) down
through the center holes of the Weight Plates (21). Insert the Selector Pin (41) into one of the
selector holes.
7. Slide Top Guide Rod Holder (14) onto the Guide Rods (5) and secure to the top of the Left Top
Frame (6L), using the two pre-installed Hex Socket Dome Bolts (56) and 5/16”Washers (64).
8. Tighten the two pre-installed Set Screws (60).
9. Tighten the Hex Dome Bolts (56).
10. Repeat steps for the other side.

17

18 HFT
Step 4: Assemble cable and pulleys
1. Fasten the Ball End of Cable (27) to the Pulley Holder (17) with two Pulleys P1 and P2 (36) using
a total of two 3/8” X 1-3/4” Hex Bolts (53) and two 3/8” Black Nylon Nuts (69), Fig A.
2. Route the Cable (27) over the two Pulleys P3 and P4 and mount Pulley P4 to the Right Top Frame
(6R) using one 3/8” X 4” Black Hex Bolt (51), two 3/8” Black Washer (63) and one 3/8” Black Nylon
Nut (69), Fig B.
3. Route the Cable (27) down trough the Pulley Block (18) and around Pulley P5. Mount the Pulley
P5 to the Pulley Block (18) using one 3/8” X 1-3/4” Hex Bolt (53) and one 3/8” Black Nylon Nut
(69), Fig C.
4. Route the Cable (27) up over the pulleys P6 and P7 (36) trough the Right Top Frame (6R). Mount
the pulleys P6 and P7 to the Right Top Frame (6R) using a total of two 3/8” X 4” Black Hex Bolt
(51), four 3/8”Black Washer (63) and two 3/8”Black Nylon Nut (69), Fig B.
5. Route the Cable (27) down through the pulley holder on the Base Frame Leg and around pulley
P8 (36). Mount the pulley to the pulley holder using one 3/8”X 1-3/4” Hex Bolt (53) and one 3/8”
Black Nylon Nut (69), Fig. D.
6. Route the Cabel (27) up and screw the Bolt End of Cable (27) for at least 1/3 into the Bold Holder
that is welded onto the Right Pulley Height Adjuster (15R), Fig. E.
7. Repeat the steps for the other side.
LNOTICE
To tighten the cables, adjust the screw conntections on the Height Adjuster (Fig. E) or on the
Pulley Block (18) (Fig. C).
8. Tighten all Jam Nuts rmly (Fig. C and Fig. E).

19

20 HFT
Step 5: Assemble right and left panel
1. Loosely attach Weight Panels (10R & 11L) to the Reae Upright Frames (4) using eight Plastic
Studs (43), four 1/4”X 6” Hex Bolts (54), eight 1/4”Washers (66), and four 1/4” Nylon Nuts (70).
2. Loosely attach Weight Panels (10R & 11L) to the Base Frame Legs (1R & 1L) using two pre-
installed 5/16” X 1/2” Button Head Bolts (55) and two 5/16”Washers (65).
3. Tighten all Weight Panel (10R & 11L) bolts.