Body Craft X2 User manual

INSTRUCTION MANUAL
X2 GYM STRENGTH TRAINING SYSTEM
76600A
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have
questions, or find missing or damaged parts, we will guarantee your complete satisfaction through
our authorized dealer service centers or our home office customer service department. Please call
your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained
technicians will provide immediate assistance to you, free of charge.

1
BEFORE YOU BEGIN
Congratulations and thank you gor selecting the BODYCRAFT X2 GYM
strength training system. The BODYCRAFT X2 GYM offers an impressive
array of strength training exercises to develop every major muscle group of the
body. Whether your goal is cardiovascular fitness, a shapely, toned body or
dramatic muscle size and strength, the BODYCRAFT X2 GYM will help
you achieve the specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT X2 GYM. Keep this manual for future reference.
If you have additional questions, please call your local BODYCRAFT X2 GYM
dealer or our customer service department at 800-990-5556 Monday through 
Friday, 9 a.m. until 5 p.m. Eastern Time.
IMPORTANT SAFETY NOTES
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with pre-existing health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1.This product must be assembled on a flat, level surface to assure its
proper function.
2.Clean pads and frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3.Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4.Keep children away from the BODYCRAFT X2 GYM at all times.
5.Keep your hands away from cables and pulleys during operation.
Keep your hands away from moving parts other than the designated
handles.
6.When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7.Make certain all cables are seated within the pulleys before every use.
8.Exercise with care to avoid injury.
9.If unsure about the proper use of the BODYCRAFT X2 GYM strength
training system call your local BODYCRAFT dealer or our customer
service department at 800-990-5556.

2
EXPLODED VIEW
141
31
B
A
7
154
104
147
134
132
138
154
154
128
132
143
128
147
154
154 148
135
148
154
132
132
154
147
128
151
155
154
153
146
154
132 165
166
116A
139
149
154
136
101
123
154
147
135
142
108
108
143
147
123 126
132
105
122
132
132
132
122
122
132
153
153
154
154
154
86
128
147
154
161
163
162
164
147
147
154
154
147
132
154
131
147 147
154
138
128
147
134
104
103
103
158
158
158
158
157
157
103
103
147
138
148
141
150
137
154
147
147
105
154
154
154
154
137
132 123
132
132
153
102
160
140 155
153
156
156
147
144
144
33A
154
153
154
132 144
130
140
154
154
154
154
128
128
153
133
123
154
141
82
30
87
31
22
32
95
80
13
84
64
98
83
40
40
29
45
26
42
26
26
62
62
2
81
31
39
20
69
157
69
69
157
69
66
88
88
88
88
88
88
103
158
157
69
66
66
66
158
157
103
69
66
66
76
76
18
19
87
70
15
14
98
98
99
90
90
160
159
159
36
93
93
93
70
64
64
64
37
38
12
33
77
85
64
75
17
75
68
79
27
26
74
43
44
45 34
74 41
43
44
154
125
132
132
147
154
147
141
78
28
64
72
13
96
97
32
21
77
132
132
132
126
123
128
147
153
147
154
133
148
150
137
141
100
25
64
73
16
77
85
23
87
24
98
62
64
38
37
79
23
89
89
72
35
11
92
98
10
40
91
91 85
40
68
68 85
24
5
2
1
3
4
8
6
9
86
58
58
156
17R
17L
147
156
131
147

3
EXPLODED VIEW
A
B
50
145
2
145
146
146
132
124
124
138
154
154
154
147
147
106
107
134
134
154
147
147
147
147
134
147
154
147
147
147
147
127
127
127
128
128
130
130
128
147
128
147
147
147
147
124
129
146
146
152
154
152
153
153
132
154
145
145
121
121
145
152
145
121
123
123
153
153
146
153
82
82
94
94
75
75
63
53
63
63
89
47
54
75
75
57
57
52
62
62
46
49
48 89
61
71
71
65
55
79
51
87
154
132
130
56
56
75
75
57
A
B

PARTS CHART
NO. DESCRIPTION QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17R
17L
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
33A
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
1
3
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
2
4
1
4
1
2
2
4
3
4
1
1
2
1
1
2
2
1
2
2
2
4
4
4
1
1
1
1
1
1
1
1
1
1
2
3
2
BASE FRAME
BASE STABILIZER
REAR UPRIGHT
FRONT UPRIGHT
WEIGHT STACK BASE (Leg Press Side)
WEIGHT STACK BASE (Low Row Side)
WEIGHT STACK TOP (Leg Press Side)
WEIGHT STACK TOP (Low Row Side)
LOW ROW BASE
TOP FRAME-bearing pre-installed
LAT BAR HOLDER
PRESS ARM SELERTOR
GUIDE ROD (2017mm)
ROW PLATE
1/2" ROW PLATE ROLLER
PULLEY GUIDE ROD (1895mm)
PRESS ARM
RIGHT HANDLE OF PRESS ARM
LEFT HANDLE OF PRESS ARM
FRONT SEAT FRAME
FRONT CHROME SEAT ADJUSTER
LEG EXTENSION ARM-bearing pre-installed
REAR SEAT FRAME
REAR CHROME SEAT ADJUSTER
SEAT BACK ADJUSTER
METAL HINGE FOR SEAT BACK
ADJUSTER
SINGLE PULLEY BLOCK
PULLEY GUIDE BRACKET
CABLE ARM ASSEMBLY
CABLE ARM
SWIVEL CABLE ARM TOP
ADJUSTABLE PULLEY BLOCK
1" CHROME ROLLER TUBE
WEIGHT STACK SHROUD
1" PIVOT AXLE
19.95mm AXLE
CABLE ARM COLLAR
LAT BAR
LOW ROW BAR
LEFT POSTER PLATE
RIGHT POSTER PLATE
LEG EXTENSION AXLE
608ZB BEARING
STEEL SPACER(all pre-assembled)
AXLE COLLAR(all pre-assembled)
BEARING BASIN(all pre-assembled)
BEARING(all pre-assembled)
BEARING COVER(all pre-assembled)
LEG PRESS MAIN FRAME
LEFT LEG PRESS HANDLE
RIGHT LEG PRESS HANDLE
LONG LEG PRESS CONNECTOR
(812mm)
FRONT LEG PRESS SUPPORT
LEG PRESS TO WEIGHT BASE
CONNECTOR(512mm)
REAR LEG PRESS SUPPORT
FOOT PLATE CONNECTOR
FOOT PLATE
BACK PAD ADJUSTER
BEARING HOUSING(all pre-assembled)
LEG PRESS AXLE
40 X 80mm ELLIPTIC PLUG
4
12
3
4
16 18
19
23
34
28 29 31
24
21
17
20 22
32
25
33
33A
30
26 27
49
46 48
5150
47
37 3835 36
39 40 41 42 43 44 45
55 56 57
52 53 54
6 7 8
5
10 11
9
12
13 14 15
17R 17L
58

PARTS CHART
NO. DESCRIPTION QTY.
61
62
63
63A
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
116A
1
6
3
1
8
1
6
1
3
6
2
2
8
1
4
8
2
3
2
3
2
1
41
2
4
4
1
4
6
4
2
2
2
4
2
2
2
38
6
1
1
2
1
6
2
2
1
1
8
1
1
1
1
1
1
1
1
2
45 X 75mm RECT. CAP
50mm SQ. CAP
45 X 75mm RECT. PLUG
50 X 75mm RECT. PLUG
50mm SQ. PLUG
45mm SQ. PLUG
PLASTIC WASHER
30 X 60mm RECT. PLUG
25 X 50mm RECT. PLUG
PLASTIC COVER
1/2" ROUND PLUG
SPACER
PLASTIC GUIDE ROD HOLDER
1" PLASTIC BUSHING(pre-assembled)
28.6mm STEEL BUSHING(all pre-assembled)
25.4mm STEEL BUSHING(all pre-assembled)
1/2" X 1-1/8" BEARING(all pre-assembled)
LONGER POP PIN(one pcs. pre-assembled)
CLUTCH LEVER OF CABLE ARM
LOCKING SPRING KNOB
SELECTOR PIN
L PIN
PULLEY(four pcs. pre-assembled)
SMALL PULLEY IN SWIVEL ARM
(all pre-assembled)
RUBBER DONUT
ADJUSTABLE STOPPER(all pre-assembled)
1/2" STOPPER(all pre-assembled)
LEG PRESS STOPPER(all pre-assembled)
COVER OF FOAM PAD
1" X 200mm HAND GRIP(all pre-assembled)
1" X 140mm HAND GRIP(all pre-assembled)
1" X 70mm PRESS ARM STOPPER
(all pre-assembled)
LAT BAR HOLDER COVER(95mm)
(all pre-assembled)
100 X 150mm NON SLIP
120 X 280mm NON SLIP
SELECTOR ROD
TOP PLATE
10 LB. PLATE
SNAP HOOK
LOW ROW CHAIN
AB CRUNCH STRAP
SINGLE HANDLE
ANKLE STRAP
FOAM PAD
BACK PAD
SEAT PAD
BACK PAD FOR LEG PRESS
SEAT PAD FOR LEG PRESS
TRIM FOR WEIGHT SHROUD
PRESS CABLE
LOW CABLE
AB CRUNCH CABLE
TOP CABLE
CABLE ARM CONNECTING CABLE
CABLE ARM CABLE(pre-assembled)
REMOVABLE END CABLE ARM CABLE
(pre-assembled)
LEG PRESS CABLE
CLUTCH CABLE
5
101100
108
98
93
99
95
96 97
94
116
116A
114
113
112
111
110
115
109
105
104
103102
64
65 66 67
62 63 63A61
71 72 73 74
69 7068
78 79 80 81
76
77
75
91 9289 9088
85 86 8783 8482
107106

PARTS CHART
0
(inch) 1" 2" 3"1/21/4 3/4 1/2 1/2 4" 5" 6"1/2 1/2 1/2
NO. DESCRIPTION QTY.
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
3
4
12
4
1
2
4
18
1
4
2
33
4
8
16
2
3
4
4
5
5
2
6
6
6
12
67
18
4
2
2
3
23
64
3
4
6
6
2
2
1
2
2
2
2
2
5/8" X 6-1/2" HEX BOLT
1/2" X 4" HEX BOLT
1/2" X 3" HEX BOLT
1/2" X 1-3/4" HEX BOLT
3/8" X 5-3/4" HEX BOLT
3/8" X 4-1/2" HEX BOLT
3/8" X 4" HEX BOLT
3/8" X 3" HEX BOLT
3/8" X 2-3/4" HEX THREADED BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 2-1/2" HEX BOLT
3/8" X 1-3/4" HEX BOLT(four pcs. pre-
assembled)
3/8" X 1-3/4" HEX THREADED BOLT
3/8" X 1" HEX THREADED BOLT
5/16" X 1/2" HEX THREADED BOLT
5/16" X 1-1/2" SET SCREW(all pre-
assembled)
5/16" X 5/8" SET SCREW(all pre-
assembled)
3/8" X 5/8" SET SCREW(all pre-
assembled)
3/8" X 1/2" ROUND BOLT(all pre-
assembled)
3/8" X 1/2" SET SCREW(all pre-
assembled)
5/16" X 1/4" SET SCREW(all pre-
assembled)
TOP PLATE BOLT
8mm X 53mm FEMALE BOLT FOR
POSTER
6mm X 12mm MALE NUT FOR
POSTER
5/8" WASHER
1/2" WASHER(four pcs. pre-assembled)
3/8" WASHER
5/16" WASHER(two pcs. pre-assembled)
3/8" SPRING WASHER(all pre-assembled)
5/16" SPRING WASHER(all pre-assembled)
24mm NYLON NUT(all pre-assembled)
5/8" NYLON NUT
1/2" NYLON NUT(four pcs. pre-assembled)
3/8" NYLON NUT(four pcs. pre-assembled)
5/16" NYLON NUT(all pre-assembled)
3/8" X 5/8" INNER HEX SCREW
5/16" X 32mm SUNKEN HEAD SCREW
5/16" NUT
1-1/4" HAND GRIP
1" T SHAPE END PLUG
HOOK PLATE
COLLAR
SEALING RING
M6 SET SCREW
M5 X 18mm ROUND HEAD SCREW
M5 NYLON NUT
6
151 152
153 154 155
145 146
147 148 149 150
121
122 123 124
125 126 127 128
129 130 132131
142 144143
135 136 137
133
138 139 140
141
134
159 160 161 162 163 164
165 166
158157156

7
9
140
153
154
123
123
128
123
147
147
147
147
147
147
130
130
128
147
153
153
123
154
153
153
153
153
2
2
1
154
6
5
4
3
14
93
93
64
64
64
64
123
70
72
77
77
49
51
72
72
70
62
62
62
62
15
154
128
147
147
ST E P 1 A SSE M B L E B A SE F R A M E
To ease the assembly process, do not tighten bolts until instructed.
1. Attach Base Stabilizers(2) to each end of Base Frame(1), using two 1/2" X 3" Hex Head Bolt(123) and
two 1/2" nut(153). Attach 50mm SQ. Cap(62) onto front & rear Base Stabilizers(2).
2. Attach Weight Stack Base - Leg Press Side(5) and Weight Stack Base - Low Row Side(6) to Base
Frame(1) using two 1/2" X 3" Hex Head Bolts(123), two 1/2" Washers(146) and two 1/2" Nylon nuts
(153). Attach four 50mm SQ. Plugs(64) and insert four Plastic Guide Rod Holders(72) to both Weight
Stack Bases(5, 6).
3. Attach Front Upright(4) to Base Frame(1) using two 3/8" X 3" Hex Head Bolts(128), four 3/8" Washers
(147) and two 3/8" Nylon Nuts(154). Repeat process for Rear Upright(3). Screw Longer Pop Pin(77)
into Front Upright(4) and Rear Upright(3) as shown.
4. Attach Low Row Base(9) to Weight Stack Base(6) using two 1/2" X 3" Hex Head Bolts(123) and one
1/2" Nylon Nut(153). Attach Row Plate(14) to Low Row Base(9) by inserting 1/2" Row Plate Roller(15).
Insert 1/2" Round Plug(70) into 1/2" Row Plate Roller(15). Attach 100 X 150mm Non Slip(93) to Row
Plate(14).
5. Attach Leg Press To Weight Base Connector(51) to Weight Stack Base(5) using two 3/8" X 2-3/4"
Hex Bolts(130), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154).
6. Attach Long Leg Press Connector(49) to Base Frame(1) using two 3/8" X 3" Hex Head Bolts(128), four
3/8" Washers(147) and two 3/8" Nylon Nuts(154).

8
3
153
123
123
122
122
122 122
154
147
147
128
63A
153
153
153
4
15
6
7
8
11
10
25
72
72
16
84
84
72
72
13
13
13 13
95
96
97 41
80
28
28
41
27
42
42
142
154
141
141
146
147
147
153
128
147
147
ST E P 2 A SSE M B L E T O P F R A M E

1. Attach Top Frame - bearing pre-installed(10) to Front and Rear Uprights(3, 4) using two 1/2" X 4"
Hex Head Bolts(122) and two 1/2" Nylon Nuts(153). Attach Lat Bar Holder(11) to Top Frame -
bearing pre-installed(10) using two 3/8" X 3" Hex Head Bolts(128), four 3/8" Washers(147) and two
3/8" Nylon Nuts(154).
2. Slide two Rubber Donuts(84) onto one end of each Guide Rod(13) and then insert Guide Rod(13)
into the Plastic Guide Rod Holders(72) in Weight Stack Bases(5, 6) as shown.
3. Slide each 10 LB Plate(97) over Guide Rods(13). Make certain that each plate is oriented with
selector hole on bottom and facing forward. Attach Top Plate(96) to Selector Rod(95) using Top
Plate Bolt(142). Slide Top Plate(96) and Selector Rod(95) over Guide Rod(13). Insert Plastic Guide
Rod Holders(72) into both Weight Stack Tops(7,8) and then slide both Weight Stack Tops(7 , 8)
over top of Guide Rods(13) and attach to Top Frame - bearing pre-installed(10), using two 1/2" X 3"
Hex Head Bolts(123) and two 1/2" Nylon Nuts(153). Refer to drawing to be certain each Weight
Stack Top(7,8) is on proper side.
4. Attach pre-assembled Cable Arm Assembly(27) to Rear Upright(3) and Base Frame(1) using two
3/8" X 3" Hex Head Bolts(128), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154). Attach pre-
assembled Cable Arm Assembly(27) to Base Frame(1) using two 1/2" Washers(146) and two 1/2"
Nylon Nuts(153) onto pre-welded bolts on Base Frame(1). Remember to keep all bolts loose to
ensure holes will align easily.
5. Slide the axle of each Cable Arm(28) through the hole in selector plate of Cable Arm
Assembly(27) and fasten using Axle Collar(42) with 5/16" X 5/8" pre-inserted Set Screw(141).

9
3
137
148
154
148 137
157
157
147
147
128
150 126
147
150 133
105
105
128
141
147
147
104
104 134
147
154
141
128
134 147
147
147
133
1
4
23
21
64
79
68
68
24
31
23
24
31
20
19
68
133
154
39
79
22
126
128
154
147
154
147
31
81
69
69
88
88
66
157
69
88
66
157
69
88
66
66
157
69
88
66
157
69
88
66
18
ST E P 3 A SSE M B L E SE A T S

1. Attach Front Seat Frame(18) to Front Upright(4) using two 3/8" X 3" Hex Head Bolts(128), four 3/8"
Washers(147) and two 3/8" Nylon Nuts(154). Attach Front Seat Frame(18) to Base Frame(1) using two 3/8"
X 4-1/2" Hex Head Bolts(126), four 3/8" Washers(147) and one 3/8" Nylon Nut(154).
2. Attach Leg Extension Arm - bearing pre-installed(20) to Front Seat Frame(18) by inserting Leg Extension
Axle(39). Fasten Leg Extension Axle(39) using two 5/16" Washers(148), two 5/16" Spring Washers(150) and
two 5/16" X 5/8" Set Screws(137). Attach 50mm SQ. Plug(64) to front of Seat Frame(18) and 38mm SQ.
Plug(66) to top and bottom of Leg Extension Arm - bearing pre-installed(20). Check to ensure that Leg
Extension Arm - bearing pre-installed(20) pivots freely. Note: The L Pin(81) is used to lock the Leg Extension
Arm - bearing pre-installed(20) into place.
3. Insert 1" Chrome Roller Tube(31) into hole in Front Chrome Seat Adjuster(19). Moisten Foam Pad(103) with
water and slide onto each end of 1" Chrome Roller Tube(31). Attach Plastic Washer(66) to both side of
Cover of Foam Pad(88) and secure the Pads with Plastic Cover(69) using 5/16" X 32mm Sunken Head
Screw(157). A Rubber Mallet is useful. Lock 1" Chrome Roller Tube(31) into place with pre-installed set
screw.
4. Attach Seat Pad(105) to Front Chrome Seat Adjuster(19) using two 3/8" Washers(147) and two 3/8" X 1-3/4"
Bolts(133). Attach 25 X 50mm Rect. Plug(68) to rear of Front Chrome Seat Adjuster(19). Insert Front
Chrome Seat Adjuster(19) into the Front Seat Frame(18) and lock into place with Locking Spring Knob(79).
5. Attach Seat Back Adjuster(23) to Front Upright(4), using one 3/8" X 3" Hex Head Bolt(128) and one 3/8"
Nylon Nut(154). It may be necessary to tighten this bolt, then loosen just enough to let Seat Back
Adjuster(23) pivot freely. Longer Pop Pin(77) should seat into adjustment holes in Seat Back Adjuster(23).
Slide two Metal Hinges(24) to axle on top of Seat Back Adjuster(23), then attach Back Pad(104) to Metal
Hinges(24) using two 3/8" Washers(147) and two 3/8" X 1" Bolts(134).
6. Attach Rear Seat Frame(21), Rear Chrome Seat Adjuster(22), Seat Back Adjuster(23) and pads using the
same procedure as above for front seat. Insert 1" Chrome Roller Tube(31) into hole in Seat Back
Adjuster(23). Moisten two Foam Pads(103) with water and slide onto each end of 1" Chrome Roller
Tube(31). Attach Plastic Washer(66) to both side of Cover of Foam Pad(88) and secure the Pads with
Plastic Cover(69) using 5/16" X 32mm Sunken Head Screw(157). Lock into place with pre-installed set
screw.
7. Insert 1" Chrome Roller Tube(31) into hole in Leg Extension Arm - bearing pre-installed(20). Moisten Foam
Pad(103) with water and slide onto each end of 1" Chrome Roller Tube(31). Attach Plastic Washer(66) to
both side of Cover of Foam Pad(88) and secure the Pads with Plastic Cover(69) and 5/16" X 32mm
Sunken Head Screw(157). Lock into place with pre-installed set screw.

10
127
127
147
147
121
121
153
153
146
107
147
147
134
134
106
145
152 147
147
128
145
145
123
153
153
152
147
147
134
129
154
147
154
147
154
145
49
58
58
51
46
71
71
55 65
79
54
53
61
47
89
89
48
62
50 52
56
56
62
2
63
63
63
140
33A
140
64
64
64
12
10
17
33
ST E P 4 A SSE M B L E B E NC H PR E SS A ND L E G P R E SS

1. Attach Press Arm Selector(12) to Top Frame - bearing pre-installed(10) by aligning holes and inserting
1" Pivot Axle(33). Lock into place with pre-installed set screw.
2. Attach Press Arm(17) to Press Arm Selector(12) by aligning holes and inserting 1" Pivot Axle(33),
19.95mm Axle(33A). Lock into place with pre-installed set screw. Attach 50mm SQ. Plug(64) onto ends of
Press Arm(17) and Press Arm Selector(12).
3. Check Longer Pop Pin(77) into Press Arm Selector(12), making sure Pop Pin(77) seats into
adjustment holes in Press Arm(17).
4. Attach Leg Press Main Frame(46) to Leg Press to Weight Base Connector(51) and Long Leg Press
Connector(49), using two 3/8" X 4" Hex Bolts(127), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154).
5. Attach Base Stabilizer(2) to Leg Press Main Frame(46) using two 1/2" X 3" Hex Head Bolts(123) and
two 1/2" Nylon Nuts(153). Attach 45 X 75mm Rect. Cap(61) to rear of Leg Press Main Frame(46) and
two 50mm SQ. Caps(62) to Base Stabilizer(2).
6. Remove one Bearing Housing(56) from Leg Press Main Frame(46). Slide Axle on Rear Leg Press
Support(52) into each Bearing Housing(56), then attach Bearing Housing(56) back onto Leg Press
Main Frame(46). Attach Front Leg Press Support(50) to Leg Press Main Frame(46) using one 5/8" X 6-
1/2" Hex Head Bolt(121), two 5/8" Washers(145) and one 5/8" Nylon Nut(153).
7. Slide both Leg Press Axles(57) through pre-installed 1" Bushings(75) on Foot Plate Connector(53).
Attach Foot Plate Connector(53) to Rear Leg Press Support(52) and Front Leg Support(50) using one
each 5/8" X 6-1/2" Hex Head Bolt(121), two 5/8" Washers(145) and one 5/8" Nylon Nut(152).
8. Attach Foot Plate(54) to Foot Plate Connector(53), using two 1/2" Washers(146) and two 1/2" Nylon
Nuts(153). Attach 45 X 75mm Rect. Plugs(64) to Foot Plate(54). Attach Right and Left Leg Press
Handles(47, 48) to Leg Press Main Frame(46), angle facing up, using two 3/8" X 3" Hex Head Bolts
(128), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154). Attach Seat Pad for Leg Press(107) to
Leg Press Main Frame(46), using two 3/8" Washers(147) and two 3/8" X 1" Hex Head Bolts(134), one
3/8" X 2-3/4" Hex Head Bolt(129). Attach Back Pad for Leg Press(106) to Back Pad Adjuster(55) using
two 3/8" Washers(147) and two 3/8" X 1" Hex Head Bolts(134). Slide Back Pad Adjuster(55) into Leg
Press Main Frame(46) by pulling pre-installed Locking Spring Knob(79).

Tighten all the bolts and nuts gradually, from ground - up.

11
FIG 6
FIG 5
FIG 4
154
133
82
30
154
109
109
109
132
FIG 2 STP 1
4
12
FIG 3
154
132
109
147
147
4
82
82
10
95
FIG 1
109
FIG 6
FIG 5
FIG 2
FIG 3
FIG 2 STP 2
FIG 3
FIG 1
FIG 4
PR E SS C A B L E
Assemble cables and pulleys simultaneously.

Attach loop end of Press Cable(109) to the bracket on Front Upright(4). Route cable
over and around left (as if sitting on seat) side pulley mounted in Press Arm
Selector(12), under and around pulley mounted in Front Upright(4), over and around
right side pulley in Press Arm Selector(12) as shown Fig. 2. Continue through
(uppermost) slot and over pulley in Front Upright as shown in Fig. 3, under top pulley
in Adjustable Pulley Block(30), up and over pulley mounted on Top Frame(10), as
shown in Fig. 4, down and around top pulley in Adjustable Pulley Block(30), up and
over pulley mounted in Weight Stack Top(8&9), and down to weight stack. Screw
Press Cable(109) end into Selector Rod(95) at least 7 threads as shown in Fig. 6.

12
FIG 1
9132
110
154
82
FIG 5 110
102
98
99
36
98
FIG 3
110
132
154
82
30
FIG 2
110
132
154
82
9
FIG 4
110
132
154
82
6
FIG 5
FIG 1 FIG 4
FIG 2
FIG 3
L O W C A B L E


Route Low Cable(110) under two Pulleys(82) on Low Row Base(9) as shown in Fig. 1,
and 2, up over lower pulley in Adjustable Pulley Block(30) as shown in Fig. 3, down and
ending under the pulley on Weight Stack Base(6) as shown in Fig. 4.

Do not use this cable if you have purchased this option Hip Station. Use this Hip
Station Cable instead.

13
FIG 1
100
111
98
FIG 2
111
154
131
147
147
4
82
FIG 3
111
154
133
82
FIG 5
111
FIG 4
132
154
82
30
111
FIG 1
FIG 3
FIG 3
FIG 4
FIG 2
FIG 5
FIG 3
A B C R UNC H C A B L E


Route the AB Crunch Cable(111) through(lower) slot and over pulley in Front Upright(4)
as shown in Fig. 2, down and around the pulley mounted on rear of Front Upright(4),
up and over lower pulley in Adjustable Pulley Block(30) as shown in Fig. 4, down and
under two pulleys mounted on Base Frame(1) and attach cable end to bracket welded
on Leg Extension Arm(20) as shown in Fig. 5.

14
FIG 2
154
132
82
112
FIG 4
95
112
FIG 5
FIG 1
FIG 2
FIG 3
FIG 4
T O P C A B L E


Route threaded end of Top Cable(112) over pulley mounted to Top Frame(10) as
shown in Fig. 1, through slot in Rear Upright(3), over pulley in Top Frame(10), under
and around top pulley in Pulley Block(30), up and over pulley mounted on Weight
Stack Top(7), under top pulley in Adjustable Pulley Block(30) as shown in Fig.3, up and
over pulley mounted to Weight Stack Top(7) as shown in Fig. 2, and down to weight
stack. Screw cable end into Selector Rod(95) at least 7 threads as shown in Fig. 4.
FIG 5
112
35
98
FIG 3
154
133
82
30 112
FIG 1
132
154
112
10
82

15
FIG 1
113
FIG 3
113
25
FIG 2
132
154
113
82
30
FIG 3
FIG 2
FIG 1
C A B L E A R M C O NNE C T T I NG C A B L E


Hook Cable Arm Connecting Cable(113) on bracket welded to Cable Arm Assembly(27)
then route up and over low pulley in Adjusterable Pulley Block(30) as shown in Fig. 2, then
screw threaded cable end into Single Pulley Block(25).

16
27 41
42
28
82
132
141
114
154
FIG 2
98
114
101
FIG 7
FIG 5
132
154
25
82
114
82
27
26
114
154
132
FIG 3
FIG 4
82
82
27 26
26
154
147
147
125
82
28 114
154
132
FIG 1
82
28 114
154
132
FIG 6
FIG 5
FIG 7
FIG 6
FIG 2
FIG 3
FIG 2
FIG 1
FIG 7
FIG 4
C A B L E A R M C A B L E


Slide Single Pulley Block(25) onto Pulley Guide Rod(16). Insert top end of Pulley Guide
Rod(16) into top guide roe holder welded to Top Frame(10). Push Pulley Guide Rod(16)
up into hole as far as possible, then slide bottom end of Pulley Guide Rod(16) into
guide rod holder welded to Base Frame(1). Secure Pulley Guide Rod(16) by tightening
pre-installed set screw. Attach pulleys and Pulley Guide Brackets(26) to Cable Arm
Assembly(27) as shown in Fig. 3 and Fig. 4. Be certain that, when tightened, the pulley
guide brackets do not interfere with cable movement. Route Cable Arm Cable(114)
aronnd these pulleys as shown, up and around pulley in the Single Pulley Block(25).

17
FIG 3
154
133
116
82
STP 1
46
52
FIG 5 FIG 5 STP 2
FIG 1
5
116
FIG 2
132
154
82
30
116
FIG 4
154
133
82
46
116
FIG 6
116
FIG 2
FIG 1
FIG 3
FIG 4
FIG 5
FIG 6
L E G PR E SS C A B L E


Screw threaded end(approx. half way) of Leg Press Cable(116) into receiver on Base
Frame(1). Route cable up and over the lower pulley in Adjustable Pulley Block(30), then
down and under the pulley on Weight Stack Base(4) as shown in Fig. 3. Then route cable
under Weight Stack Base(5) as shown in Fig. 1, and around horizontal pulley on Leg Press
Main Frame(46). Route cable under and around lowest pulley mounted on Rear Leg Press
Support(52), under and around right side(as if sitting on seat) pulley on Leg Press Main
Frame(46), over and around top pulley on Rear Leg Press Support(52), under and around
left side pulley on Leg Press Main Frame(46) as shown in Fig. 5. Then hook the terminal
end of cable on bracket on Rear Leg Press Support(52) as shown in Fig. 6.

18
143
148
143
32
32
148
135
135
144 37
37
38
38
8
7
4
5
6
3
148
148
135
108
135
ST E P 5 A SSE M B L E W E I G H T ST A C K SH R O UDS 
A ND PO ST E R PL A T E S
1. Attach Weight Stack Shrouds(32) to Weight Stack Bases(5 , 6) and Tops using 5/16"
Washers(148) and 5/16" X 1/2" Hex Head Bolts(135). Remember to keep all bolts loose
in frame to ensure holes line up easily.
2. Attach Poster Plates(37, 38) to Rear and Front Uprights(3 , 4) using 8 X 53mm Female
Bolts(143) and 6 X 12mm Male Nuts(144).
3. Trim two Trims for Weight Shroud(108) on Weight Stack Shroud(32).

Assembly is complete! Please take the following steps before using the gym:
1.
2.

3.


4.
5.


6.

7.
Make certain all bolts are tightened securely.
Make certain all cables are seated into all pulley grooves. A cable rubbing
against steel will peel the nylon coating, voiding warranty and resulting in a
need for replacement.
Pre-stretch the cables. Put the Weight Selector Pin (80) in the bottom hole on
the weight stack. Pull on the cables with great force, helping remove any
kinks and providing any initial cable stretch.
Be aware the cables can loosen and slightly stretch upon initial use.
The cables should be adjusted as tight as possible, but no so tight as to lift
the Top Plate (96) above the weight stack. Be certain to secure the jam nuts
after adjustments are made.
For better performance, apply a household lubricant (such as silicone) to any
adjustable areas and to the Guide Rods (16).
Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the Bodycraft X2 Home Gym. If You have
any questions, please call your local BodyCraft dealer or call our
customer service department at 800-990-5556