Boland PVB17 User manual

User Manual
1 of 26
Multi Format LCD Monitor
User Manual
PVB-Series

User Manual
2 of 26
CAUTION ...................................................................................................................................................... 3
FEATURES ................................................................................................................................................... 5
CONTROLS, INDICATORS AND CONNECTIONS ..................................................................................... 6
MENU BASIC OPERATION ....................................................................................................................... 11
PICTURE MENU ......................................................................................................................................... 13
AUDIO MENU ............................................................................................................................................. 16
DISPLAY MENU ......................................................................................................................................... 17
REMOTE MENU.......................................................................................................................................... 20
SETUP MENU............................................................................................................................................. 21
INFO MENU ................................................................................................................................................ 23
INPUT SUPPORT MODE............................................................................................................................ 24
MECHANICAL DIMENSION....................................................................................................................... 26

User Manual
3 of 26
Caution Before operating the set, please read this manual carefully.
WARNING:
To reduce the risk of electric shock does not remove cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel. To prevent fire or shock hazard, do not expose the rear of
the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as this may
scratch, mark, or damage the Active Matrix LCD permanently.
Unauthorized tampering with the inside of the monitor invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair. Work
by third parties.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, improper use can
result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built
into your new product, please read and observe the following safety points when installing and using your
new product and save them for future reference.
Read Instructions
Follow Instructions
All operating and use instructions should be followed.
Retain Instructions
The safety and operating instructions should be retained for future reference.
Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
Cleaning
Disconnect the unit from the electricity supply before cleaning. Do not use abrasive cleaners. Use a damp
cloth for cleaning.
Water and Moisture
Do not use this apparatus near water.
Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force and uneven
surfaces may cause the product and cart combination to overturn.
Attachments
Do not use attachments not recommended by Boland as they may cause hazards.
Ventilation
Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.
Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your supplying dealer.
Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not defeat the
safety purpose of the grounding-type cord.
Power Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, convenience receptacles and
the point where they exit from the product.
Outdoor Cable Grounding

User Manual
4 of 26
Caution
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and built-up static charges. A “face
plate” also needs to be installed with an isolating capacitor to prevent any damage from static.
Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent possible damage to the product due to lightning and power-line surges.
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to avoid contact with such power lines or circuits, as
contact with them might be fatal.
Earthing the product
This product must be earthed properly to comply with the safety regulations in the country of use. If you
are unsure of these regulations, please consult a qualified electrician.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltages or other hazards. Refer all servicing to qualified service personnel. If the Set does not
operate properly, switch it off and call your dealer.
Damage Requiring Service
Isolate this product from the mains supply and refer servicing to qualified service personnel under the
following conditions:
A. If the power-supply cord or plug is damaged.
B. If the glass front has been damaged.
C. If there is ingress of water between the glass and the LCD screen.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the product to its normal
operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition and the front seal is intact.
Mounting
The product should be mounted on a wall only as recommended in the instructions.
Power
This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This appliance
must be earthed at all times through the chassis as well as through the power lead.

User Manual
5 of 26
Features
This product is the multi-format Digital LCD Panel to display various kinds of digital video input signal as
HD/SD-SDI/DVI/HDMI Digital and analog signal such as Composite/S-Video/RGB/PC-RGB/ Component.
This is also High Definition Broadcasting Monitor which can make it available to do output of stable video
signal with the menu of considering convenient user interface and the easy control for brightness and
color.
•HD/SD SDI 2INPUT/2 OUTPUT.
•WAVEFORM / Vector Scope / Time code Display.
•16 ch Audio Lever Meter Display. (SDI only/)
• Analog & Digital Signal Audio Lever Meter Display.
- Lever Meter Position display selectable
•Dual Link MODE & 1080p 60 Compatible
•Closed Caption (Analog Signal only): CEA608, 708
•H/V Delay.
• Audio Disembedder & Internal Speaker & Headphone out & Monitor out
• Color Temperature – User, VAR, 11000K, 9300K, 6500K, 5400K, 3200K
•Over Scan/Zero Scan/Under Scan/Pixel to Pixel
•PIP (Picture In Picture)/PIP Blend
•Tally LED function (Green/Red/AMBER)
•Integrated DVI (HDCP) function.
• HDMI (HDCP) function.
• Supports VESA DDC2B and a subset of VESA standards.
• Single board is suitable for mounting behind an LCD panel.
• Supported RS-232C, RS-422.
• Supported External GPI Control (RJ-45).
• OSD: Graphic based OSD, 6 Languages (UNICODE System).
• LCD Dimming Control
- Manual Dimming Level Control.
• UMD
• Auto Calibration: CA-210,CA-310(Minolta) / K-10(Klein)
• ETHERNET: Network System Controller / Update

User Manual
6 of 26
Controls, Indicators and Connections
PVB17 Front
STANDBY
SDI1
SPEAKER_L
SDI2
HDMI DVI
Composite SCAN
MARKER H/V DELAY
AUDIO WF/VT
F1 F2
MENU UP
ENTER/INPUT DOWN
ADJUST
SPEAKER_R
IR
PVB17 Rear
SDI 1 OUT
CVBS2/Y/G/Y IN
CVBS3/Pb/B/C IN
CVBS1/Pr/R IN
DVI
HDMI
RS-232 OUT
RS-232 IN
SDI 2 OUT
SDI 2 IN
SDI 1 IN
CVBS1/Pr/R OUT
CVBS2/Y/G/Y OUT
CVBS3/Pb/B/C OUT
AUDIO OUT
AUDIO IN
HEADPHONE
RS422 IN
RS422 OUT
ETHERNET
GPI
DC 12V
LAN UPDATE

User Manual
7 of 26
Controls, Indicators and Connections
PVB24 Front
STANDBY
SDI1
SPEAKER_L
SDI2
HDMI DVI
Composite SCAN
MARKER H/V DELAY
AUDIO WF/VT
F1 F2
MENU UP
ENTER/INPUT DOWN
ADJUST
SPEAKER_R
IR
PVB24 Rear
SDI 1 OUT
CVBS2/Y/G/Y IN
CVBS3/Pb/B/C IN
CVBS1/Pr/R IN
DVI
HDMI
RS-232 OUT
RS-232 IN
SDI 2 OUT
SDI 2 IN
SDI 1 IN
CVBS1/Pr/R OUT
CVBS2/Y/G/Y OUT
CVBS3/Pb/B/C OUT
AUDIO OUT
AUDIO IN
HEADPHONE
DC 12V
RS422 IN
RS422 OUT
ETHERNET
GPI

User Manual
8 of 26
Controls, Indicators and Connections
PVB47 Front
MARKER
ADJUST
SPEAKER_R
F2
H/V DELAY
SCAN
SDI1
HDMI
Composiet
AUDIO
DOWN
IR
ENTER/INPUT
UP
MENU
F1
WF/VT
SDI2
STANDBY
DVI
HEADPHONE
SPEAKER_L
PVB47 Rear
CVBS3/Pb/B/C OUT
RS-232 OUT
DVI-I
SDI 2 IN
SDI 1 IN
RS422 OUT
AUDIO IN
AUDIO OUT
CVBS3/Pb/B/C IN
CVBS2/Y/G/Y IN
SDI 2 OUT
RS-232 IN
HDMI
CVBS1/Pr/R OUT
CVBS1/Pr/R IN
CVBS2/Y/G/Y OUT
SDI 1 OUT
GPI
ETHERNET
RS422 IN
DC 24V IN

User Manual
9 of 26
Controls, Indicators and Connections
Front Keys Arrangements
STANDBY
Power ON/OFF Button. This button is operated after being pressed about 3 seconds.
SDI 1 / SDI 2
Select SDI 1/ SDI 2 source directly
HDMI
Select HDMI source directly
DVI
Select DVI source directly
Composite
Select ANALOG source directly ( ‘CVBS1’ ->‘CVBS 2’->‘CVBS 3’)
MARKER
Draw Marker on Screen (Off -> 16:9 -> 4:3 … -> 2.35:1)
H/V-DELAY
Activates ‘H & V' blanking display ‘H DELAY’ -> ‘V DELAY -> ‘HV DELAY’ -> OFF
AUDIO
Activates Audio Lever Meter
WF/VECTOR
Activates WAVRFORM & Vector Scope (SDI Only)
Setup Menu  Waveform format selecting
FUNCTION 1 ~ 2
Executes functions of user selected
(UNDEF, Aspect, Mono/Blue, Audio Group/Channel/Mute, Time code, Still image,
Caption, Aspect Marker, Area Marker, PIP func & Input, Zoom, Gamma Select, WFM Line Select.)
MENU
Activates main OSD menu
Navigates higher menu in main OSD menu
Exits OSD menu
DOWN
Decreases sound volume of speaker
Decreases values of user menu in main OSD menu
Executes function (by OSD help commands) in main OSD menu
UP
Increases sound volume of speaker.
Increases values of user menu in main OSD menu
Executes function (by OSD help commands) in main OSD menu
SEL/INPUT
Activates OSD menu of input source selecting
Changes input source by selecting
Executes functions (by OSD help commands) in main OSD menu
Activates child menu
ADJUST
Adjust Picture Menu (Brightness -> Contrast -> Color -> Sharpness->Phase & Tint)
Turn Right (with ‘UP' button is same)
Turn Left (with ‘DOWN' button is same)

User Manual
10 of 26
Controls, Indicators and Connections
REAR Panel
SDI 1/SDI 2 IN
HD SDI / SD SDI Input
SDI 1/SDI 2 OUT
SDI 1, SDI 2 Loop Out
RS-232C IN
Update /Auto color calibration
DVI-I
DVI-I Type Digital / Analog PC-RGB Video Input
HDMI
High Definition Multimedia Input
CVBS1/Pr/R In
CVBS 1, Component Pr, GBR(SOG sync) R Input
CVBS2/Y/G/Y In
CVBS 2, Component Y, GBR(SOG sync) G, S-Video Y Input
CVBS3/Pb/B/C In
CVBS 3, Component Pb, GBR(SOG sync) B, S-Video C Input
AUDIO IN
DVI-I/Component/GBR/CVBS1,2,3/S-Video Sound Input
AUDIO OUT
AUDIO MONITOR OUT
ETHERNET
Network System Control/ Firmware Upgrade
GPI
GPI 1 ~ 7 Control Port
RS422 IN/OUT
Monitor System Control
HEADPHONE
Headphone output
DC 12V/24V IN
PIN NO(4P_12V)
Description
PIN NO(5P_24V)
1
GND
1 ,2
2 , 3
4
4
+ 12V/+24V
4 , 5
1
2
3
4
12345

User Manual
11 of 26
MENU Basic Operation
In this menu system, there are several ways to customize the menu settings provided.
Most menus consist of three levels to set up the options, but some require greater depth for the variety of
settings. If you press the MENU button, only the first and second level of the menu system will appear on
the monitor screen. The third level can be displayed by pressing SEL/INPUT. If a menu has more than
three levels, the pop-up dialogue box will be displayed as the fourth or fifth level.
To show and remove the Menu
Press the MENU button to display the menu. A second press of the MENU button will take you back to
monitor viewing.
To go to the next level
Press SEL/INPUT button.
To go back to the previous level
Press MENU button
Typical Menu Operation
1. Press MENU button: The main menu will appear.
2. Use Adjust / Take button Turn Right/ Left to select the desired menu option (icon).
3. While the desired menu option is selected, press SEL/INPUT to move to the second level.
4. Use Adjust / Take button Turn Right/ Left to select the second menu option.
5. Press SEL/INPUT to move to the third level: Some menu options require additional steps.
6. Press MENU to return to the previous menu to return to monitor viewing.
Turning On the Monitor
1. First, connect power cord correctly. At this moment, the monitor switches to standby or power on mode.
In standby mode, in order to turn monitor on, press the ST-BY button.
2. Select the viewing source by using SEL/INPUT button on Keypad in front of monitor
Volume Adjustment
1. Press the Adjust / Take button Turn Right/ Left button on Keypad.
2. If you want to switch the sound off, press the FUNCTION (Audio mute) button.
3. You can cancel this function by pressing the FUNCTION (Audio mute) or volume control button.

User Manual
12 of 26
MENU Basic Operation
On Screen Menus Language Selection
- Display -> OSD Set -> Language
- The menus can be shown on the screen in the selected
language.
- Supported Language: English, Spanish, Portuguese, German,
French, Italian
How to Select Video Source by OSD
1. Press the SET/INPUT button and then UP/DOWN button to select each video source.
2. Press the SET/INPUT button to go to desired video source.
3. If Input Name is enabled, The SET/INPUT button goes into input name edit mode instead of selecting
source.

User Manual
13 of 26
PICTURE MENU
Video Menus of each Input modes
< Video (NTSC) Picture menu> < PC Picture menu> < SDI, HDMI Picture menu>
Adjust
- Adjust the values of Brightness, Contrast, Color, Tint and
Sharpness directly from -50 to 50
Contrast, Brightness, Sharpness, Color (All Sources), Tint
(without PC, DVI, HDMI, Component), Phase (Component).
Color Temp
- For Setting the Color temperature or adjusting RGB
Gain/Offset value directly
- User (User setting RGB gain value), VAR(3200K ~ 11000K),
Often used value(11000K, 9300K, 6500K, 5400K,3200K)
SCAN
1. Over Scan –95% input size and fit the selected display size
2. Zero Scan –100% Input size and fit the selected display size
3. Under Scan –105% Input size and fit the selected display
size
4. Pixel to Pixel –Display size is an input size. If input resolution
is bigger than panel size, fit the panel size
Aspect
- For setting the aspect ratio.
- Full Screen: The images are displayed with a panel size.
- Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: The images
are displayed with each aspect ratio.
- PC mode: Full Screen & 4:3 only
-AFD (Active Format Description): If this mode is selected, the
embedded Aspect ratio signal in the video signal will be
extracted and displayed as a marker.

User Manual
14 of 26
PICTURE MENU
ZOOM
- Can see the enlarged picture by (2X, 3X, 4X, 5X) ratios.
- If user select the Zoom 2X, can see the below yellow box in
picture.
- Press Select or Enter button, user can see the enlarged
picture.
- Menu key escape the zoom mode.
Picture Option
I/P Mode
 Line Doubler/inter-Field/Field Merge function on/off
Gamma Select
 Gamma Level Select (0.8 ~ 3.0)
Back Light
 Inverter dimming Level select (0~100)
Color Only
 Mono Color/Blue only Function on/off
- Mono color: For selecting monochrome images.
- Blue Only: Images have only blue color expect red and green color
Flip
 H-Flip Function on/off
Patterns
 Auto Run, 100% Color Bars, 75% Color Bars, Luma, RGB, White, Black, RED, Blue, Green
HV Delay
 Off / H / V / H+V
Output Range
 Normal (16~235)/Full (0~255)
Noise Reduction
-Noise Reduction on/off. (NR is for Video signal (HD-SDI, CVBS, S-Video and Y.Pb.Pr) & DTV timing.
NTSC Setup
- IRE value under NTSC mode between 0 IRE and 7.5 IRE.
PIP (Picture IN Picture)
- Watch two programs or source at the same time. And set up PIP size and position.
PIP ON/OFF
- Control PIP function On/Off.

User Manual
15 of 26
PICTURE MENU
Input Source
- PIP input Source can operate with different signal and type.
- Analog (CVBS 1, 2, 3, Y.Pb.Pr, GBR, PC) inputs + Digital (DVI, HDMI) + SDI (SDI1, SDI2) inputs
-SDI + SDI input PIP
Ex) AV + S-Video (X), DVI + SDI (O), PC + DVI (O), SDI1+SDI2 (O)
- PIP MATRIX TABLE
SDI 1
SDI 2
HDMI-DVI
PC_YPbPr_RGB_YC_CVBS
SDI 1
X
O
O
O
SDI 2
O
X
O
O
HDMI-DVI
O
O
X
O
PC_YPbPr_RGB_YC_CVBS
O
O
O
X
Aspect
- Choose PIP size of Small/POP1/POP2
Position
- Choose the pip position on the each corner of the pane
PIP Blend
-Blend to PIP size of Small
PIP Swap
- Using Swap option, you can exchange two programs or source at the same time.
PC Menu
- Only operate PC input mode
- Select Auto-adjust and adjust Phase, HV position, Frequency
- Auto-Adjust automatically set the optimum values of Phase,
HV position and Frequency.
-Selects X768 native PC video timings.
(Auto/1024x/1280x/1360x/1366x)
Dual Link Mode (SDI only)
-Dual Link Mode select. (Auto/Off/RGB444/YCbCr444/YCbCr422/Progressive)
PIP
POP1
POP2

User Manual
16 of 26
AUDIO MENU
Audio out
- Select Internal Speaker out. (Auto/SDI1/SDI2/HDMI/Line in)
Audio Selection
-PIP & W/F Double mode only. Select the Main or Sub.
SDI out
-SDI Audio output Group & Channel source select
SDI Gr/Ch
- Audio output Group source select. (Group1, 2, 3, 4)
- Audio output Channel source select. (Channel1~16, Channel1/2,3/4,5/6,7/8,9/10,11/12,13/14,15/16 off)
SD2 Gr/Ch
- Audio output Group source select. (Group1, 2, 3, 4)
- Audio output Channel source select. (Channel1~16, Channel1/2,3/4,5/6,7/8,9/10,11/12,13/14,15/16 off)
Volume
- Adjust the speaker or headphone Volume level.

User Manual
17 of 26
DISPLAY MENU
Marker
Aspect
- 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1&4:3, Custom fitted
panel size marker on screen.
Area
- Area: Draw dotted line Marker on screen in case of images. (16:9 95/93/90/88/80%, 4:3
95/93/90/88/80%, EBU Action 16:9/14:9/4:3, EBU Graphic 16:9/14:9/4:3)
Center Maker
- “+” Marker on center of screen
Aspect L. Color
-Marker Line Color Select. (WHITE, YELLOW, BLUE, RED, BLACK)
Area L. Color
-Area Line Color Select. (WHITE, YELLOW, BLUE, RED, BLACK)
Line Width
- Marker line thickness setting. (0~10)
Custom Marker
-The user wants Marker size setting. (Below panel size)
Waveform
Enable
- Off / Y+VT / Y+Cb+Cr/ G+B+R /Double
Key Format
- Press the W/F button to display the WAVEFORM Mode.
(Rotation, Y+VC, Y+Cb+Cr, G+B+R, Double)
Line Select
- Select line WAVEFORM & Vector Scope display.
Line Number
-Line select: Input Resolution size.
Line Display
-off/on/5 sec
Level Meter
- Display the audio level meter on screen in SDI input.
- Audio level meter cannot display with OSD.

User Manual
18 of 26
DISPLAY MENU
Type
-Pair: Respectively Channel with right and left display
-Group: Respectively group display
Position
- Level Meter Position selects. ( )
Scale
- Level Meter Scale mode selects.
(Digital/Nordic/BBC/EBU/DIN/Expanded DIN/SMPTE VU/EBU
VU/France VU)
Time code
Enable
- Time code Display (off/LTC/DVITC, SDI only)
Size
-Time code size select. (Small, Middle, Large)
Position
- Time code display position selects (L-T, C-T, R-T, L-B, C-B, R-
B)
Transparency
- Disable blending Time code background with video image. (0%, 25%, 50%, 75%, 100%)
DVITC Line
-Auto, Line 1 ~ 31
Caption
Caption
-608 Line21, 608 ANC, 608 Transcoded, 708 mode Select
608 Caption
-608 Caption mode Select. (C/C1, C/C2, C/C3, C/C4, TEXT1,
TEXT2, TEXT3, TEXT4, OFF)
708 Caption
-708 Service mode Select. (Service 1/Service 2)
OSD Set
Language
-Select a language for the menus to appear in. (English,
Spanish, Portuguese, German, French, Italian)
Position
- L-T, R-T, C, L-B, R-B
Transparency
- Disable blending OSD background with video image.
Timeout
- OSD gone time setting. (3~200)

User Manual
19 of 26
DISPLAY MENU
U.M.D
UMD
- UMD display on/off
Character
- UMD Character Select
Position
- UMD display position select. (L-T, C-T, R-T, L-B, C-B, R-B)
FG Color
- UMD Character color Select (RGB_255_192_128_0_Transpareut)
BG Color
- UMD BG color Select (RGB_255_192_128_0_Transpareut)
Input I.D.
Input ID
- source Message display.
ID Style
- select “Input Format”/”Custom Label”
Input Label
- Display user made name instead of input source name on source OSD and message OSD.
UMD
Channel-01
Tally Red
Channel-01
Tally Green
Channel-01

User Manual
20 of 26
Remote MENU
GPI Control & GPI#
- For allocating functions to particular GPI pins.
- When remote control operations are to be performed using the GPI Controller.
- GPI Control: GPI function Enable/Disable
- GPI 1 ~ 7
GPI Function
Description
Undefined
Not set (no function allocated)
Marker1 On/Off, Marker2 On/Off
Displays the markers which have been set by the
GPI PRESET1, 2 items on the screen.
Center Marker
Displays the center marker.
Safety Area
Displays the Safety Area.
Tally R, Tally G
For lighting up the Red or Green tally lamp.
Scan
Over Scan/Zero Scan/Under Scan/ Pixel to Pixel
Input CVBS 1,2,3, Input G.B.R, Input SDI
1, Input SDI 2, Input Y.Pb.Pr , Input PC ,
Input DVI, Input HDMI
Switches the input source.
Menu Key, Enter Key, Up Key, Down Key
Left Key, Right Key
Use the key function by GPI.
Function 1, Function 2
Activates FUNCTION 1, 2 buttons
Aspect
Sets the aspect ratio of the images
Waveform
Activates WAVRFORM & Vector Scope (SDI
Only)
GPI 7 : Power Key(Fixed)