BORK M783 User manual

M 783

MEAT GRINDER M783
USER MANUAL

3
PROFESSIONAL STAINLESS STEEL BLADES
The system consists of 2 professional blades; a separator blade for preparing
meat for processing, a main blade and the cutting plate.
This ensures high-quality results in the form of professionally ground meat.
UNIQUE “SMART LOCK” MOUNTING SYSTEM
The design ensures no leeway or vibration during operation: assembling takes
a single push, the head firmly sets in place, fixed to the base. An integral part
of the device is the electromagnetic sensor, which allows the unit to recognize
proper head installation and to stop its use when the head is not installed.
Thedirect drive system which connects the screw feed to the reductor ensures
high quality and reliability.
My BORK
Register your BORK equipment in your account on the bork.ru website.
You will get quick access to instructions, accessories, spare parts and reminders
for consumables replacement.

4 5
INTELLIGENT AUTO-REVERSE
The first meat grinder on the market with an automatic reverse function
when there are difficulties during meat processing. This reliably protects
the motor from failure, as well as eliminating the need for manual reverse.
LOW NOISE
The motor runs so quietly that you can use the appliance without disturbing those
around you.
Head Assembly
Tray
Plunger
The loading part
Rotary switch for operating mode selection—
button for removing the head
Motor block
Rubber feet

6 7
Lock piece for cutting plate
Screw feed Separator blade
3 mm 4 mm 7 mm
Cutting Plate Blade
3 mm grating is recommended for the preparation
ofpâtés and fillings for various fish and meat snacks.
4 mm grating grid is recommended for mincing beef,
lamb and poultry meat, as well as vegetables, hard
and semisolid cheeses.
7 mm grating is recommended for making home
sausages, minced pork, as well as for grinding dried
fruits, hard and semisolid cheeses.
Plunger Cutting plate
cleaning tool
Tool for unscrewing the cutting
plate lock
Chopping blade Grating blade
Lock piece for vegetable
cutting attachments
First attachment set for sausages
Vegetable
cutter Second attachment set for sausages
Plunger

8 9
CONTROL PANEL
— manual reverse function
(back motion)
— turning off the appliance
— speed 1
— speed 2
— еject button for removing the head
— selector
Before the first use, thoroughly wash the screw feed,
blade, head for the meat, head for the vegetables,
allattachments for the sausages, the tray, all
thecutting plates and the plunger under running
water. Dryallparts.
ASSEMBLY
• The meat grinder should be disconnected from
thepower outlet.
• Place the screw feed inside the meat grinder head.
• Place the separator blade on the screw feed
withcutting edges outwards.
• Then place the blade with the cutting edges
outwards.
• Put the cutting plate onto the screw feed –
small, medium or large, depending on desired
consistency.
Make sure that the ledge on the head is lined up
with the slot on the cutting plate.
• Tighten clockwise.
SMART LOCK system
• To install the head place the assembly
intothegrooves and press towards the body until
you hear a click.
• Place the tray on top of the head assembly.
Disassembling
• Before disassembling, disconnect the meat grinder
from the power outlet.
• To detach the head, press the button,
thenremove it by pulling on the head assembly
away from the body.
• Unscrew the lock piece of the cutting plate
counter-clockwise using the tool.
• Then remove the cutting plate, the blade
andthescrew feed.

10 11
VEGETABLE CUTTER
• Insert the required grating or chopping blade
intothe feed part for vegetables.
• Install the blade lock piece by turning it to the right
into the position.
• To install the head; place the assembly into
thegrooves and press towards the body until you
hear а click.
Grating blade
Vegetable Plunger
Lock piece for vegetable
cutter heads
Chopping blade
First attachment set for sausages
Lock piece for cutting plate
Second attachment set for sausages

12 13
THE SAUSAGE SETS
Use a natural shell: pork or lamb casings.
Rinsetheshell in the running water from theoutside
and inside, fill water for 5–7 minutes toget rid
ofexcess salt and ensure elasticity.
• Install the necessary heads onto the screw feed
according to the diagram.
• Tighten the lock piece firmly and place the feed tray
onto the feed part.
• Attach the sausage casing to the head mounted
onthe meat grinder.
• Use plunger to feed chopped meat or minced
meat to the feed part, in portions. Control the filling
ofthecasing, holding it by hand.
First attachment set
Designed for preparing home-made sausages.
Second attachment set
Used for cooking kebabs and sausages.
OPERATION
• Prepare the meat for processing by removing
bones, soft tendons and sinew, then slicing it.
• Install the head assembly onto the meat grinder.
• Connect the grinder to the power outlet.
• To turn on the meat grinder, turn the switch
totheposition – Speed 1.
• To increase the speed, turn the switch clockwise
tothe — Speed 2.
Two speeds of operation ensure that the meat
grinder selects the correct speed for each type
ofmeat:
Speed 1 — chicken, fish, berries;
Speed 2 — turkey, pork, beef, lamb, game meat.
Put the meat into the feed part.
DO NOT push products into the feed part using
objects other than the plunger.
• To stop the appliance, turn the switch
tothe position.
REVERSE
• If the rotation has slowed due to solid products,
move the regulator to position tostop the meat
grinder.
• Move and hold the regulator to the position ,
to start the reverse rotation (reverse).
Aftertheregulator returns to the position
themeat grinder stops the reverse rotation.
• Turn the regulator to the or position torestart
the meat grinder.

14 15
RULES FOR CONNECNING
TO THE POWER OUTLET
• Do not touch the power plug with wet hands.
• Connect the device only to a grounded outlet.
When disconnecting the appliance from the power
outlet, do not pull on the cord; pull only on the plug.
CLEANING
• Before cleaning, disconnect the meat grinder from
the power outlet.
• Wash all detachable parts thoroughly under running
water using a mild detergent. Thenrinse and wipe
with a soft dry cloth.
• Wipe the outer part of the meat grinder housing
with a damp cloth and soapy water. Dry with a soft
cloth.
• For a faster and easier cleaning of the cutting
plates, use the special cleaning tool.
• After cleaning, grease the blade and cutting plates
with vegetable oil.
To prevent rusting, the blade and cutting plates should
be wiped dry.
After cleaning, grease the blade and plates
withvegetable oil.
Do not wash the feed part and removable parts
inthedishwasher.
ANODIZED COATING CARE
Do not use tools with abrasive particles, citric acid,
hard sponges and wire brushes in the cleaning
process.
Chemically aggressive compounds,
alkalinedetergents have a destructive effect
ontheanodized surface.
STORAGE
It is recommended to store the device in its
assembled form, in a dry, cool place, away from
acids and bases, at a temperature of 5 to 30 °C
anda relative humidity below 65 %.
Do not expose the unit to significant temperature
changes and/or direct sunlight.

16 17
SAFETY MEASURES
• Before operating the meat grinder, carefully
read and save this manual to be able to refer
toitinthefuture.
• Before the first use, wash all the removable parts
ofthe meat grinder.
• Before operating the device, make sure that
thepower supply characteristics correspond
tothose indicated on the device’s rating label.
• Connect the device only to a grounded outlet.
Intheabsence of grounding performed
inaccordance with local regulations,
themanufacturer (the person authorized
bythemanufacturer) shall not be liable fordamages.
• Install the meat grinder only on a dry, flat surface.
• Keep the meat grinder housing clean. When
cleaning, follow the instructions in the «Cleaning»
section.
• Cutting plates for minced meat, blades, sets
forsausages, lock pieces, screw feed andscrew
feed safety lock have natural wear and tear,
theservice life depends on the frequency
andaccuracy of use.
• Do not allow clothing, hair, fingers, etc. into
themeat grinder. This is hazardous to health.
• This appliance is not intended for use
bypersons (including children) with limited
sensory orintellectual capabilities, or persons
with insufficient experience and knowledge
oftheappliance.
• Always disconnect the meat grinder from the power
outlet after use, before assembly, disassembly,
andbefore cleaning the appliance.
• Do not touch the moving parts of the meat grinder
during its operation.
• Before connecting to the power supply, make
sure that the unit is assembled according
totheinstructions, see the "Assembly" section.
• Do not immerse the meat grinder housing
withthemotor or the power cord into water, donot
wash under a tap. Do not allow moisture into
themotor compartment.
• During the operation of the meat grinder,
itisprohibited to push products using fingers
orforeign objects — use the plunger provided
withthe unit.
• Do not leave the meat grinder unattended.
• Do not overload the meat grinder. If clogged,
immediately stop the grinder and clean
thescrew feed, and the blade from the remnants
oftheproducts.
• Do not use frozen food for processing in the meat
grinder.
• It is forbidden to grind bones, nuts and other solid
products.
• The meat must first be separated from bones, soft
tendons, sinew, veins.
• Do not allow foreign objects and/or liquids
into thehousing of the appliance, this can lead
todamage.
• Do not wash the feed part and removable parts
inthe dishwasher.
• When disconnecting the appliance from the power
outlet, do not pull the cord, pull only on the plug.
• Keep the appliance in a clean, dry and cool place,
out of the reach of children.
• To prevent rusting, the blade and cutting plates
should be wiped dry.
• This device is designed for home use.
• Do not remove or damage the rating label
withinformation about the appliance anditsserial
number. It is necessary for the accurate
identification of the appliance in the event
ofa malfunction.
• Transportation of the product is allowed only
intheoriginal packaging, as well as in the fixed
position.
• Dispose of the device in accordance with the laws
and regulations of the local government.
TROUBLESHOOTING
• Upon detecting any malfunctions in the appliance,
immediately discontinue the use and transfer
ittothe nearest BORK service center for testing,
replacement or repair.
• For safety reasons, all service, repair and
maintenance of the device must be performed only
by BORK authorized service centers. Addresses
and phone numbers of service centers can be
found on the site www.bork.ru or by calling
8 800 500 88 99.

18
SPECIFICATIONS
Voltage: 230 V
Frequency: 50 Hz
Rated power: 250 W
Maximum power: 2000 W
Dimensions (H
× W × D): 395 × 191 × 320 mm
Weight: 5.6 kg
Made in China.
Information about the product designation:
the device is intended for grinding meat, fish,
vegetables when preparing meat products.
There are no special sales conditions.
CONTENTS
Meat grinder: 1 pc.
Blade: 1 pc.
Separator blade: 1 pc.
Screw feed: 1 pc.
Cutting plates: 3 pcs.
Lock piece for cutting plate: 1 pc.
Tool for unscrewing the cutting plate lock piece: 1 pc.
Plate cleaning tool: 1 pc.
Head: 1 pc.
Plunger: 1 pc.
User manual with Warranty Certificate: 1 pc.
Set for grating and chopping
Vegetable cutter: 1 pc.
Vegetable Plunger 1 pc.
Grating blade: 1 pc.
Chopping blade: 1 pc.
Set of heads
First set for sausage: 3 pcs.
Second set for sausage: 2 pcs.
Due to constant product improvement,
themanufacturer reserves the right to make changes
in the design, configuration and specifications.
The latest version of this manual can be found
onthewebsite www.bork.ru.
Dear customers, if you have any questions related to purchase, operation and maintenance of BORK equipment, you can use the phone number
8 800 500 88 99 (Information support service).

20
PLATINUM COLLECTION

INFORMATION ABOUT CERTIFICATION
The product is certified.
WARRANTY CARD
The BORK company provides a one-year warranty from the date of purchase of this product The service life determined by BORK representatives for this product amounts to 3 years from the date
of sale, provided that the product is used in accordance with rules and recommendations set out in the operating manual attached to it and applicable technical standards.
In order to avoid misunderstandings, we ask you kindly to carefully study the user manual, terms
of the warranty, check correctness of the warranty card. The warranty card is valid ifa user
has a correct and legible specification of the following information: model, serial number
oftheproduct, date of sale, clearly visible seals of the seller, buyer's signature. The model
andserial number ontheproduct shall comply with those indicated in the warranty card.
The warranty shall be deemed null and void if any of these conditions are violated and when
data, specified in the warranty card, is altered, deleted or overwritten. If the date of sale can
notbeestablished in accordance the warranty period and lifetime shall be calculated from
thedateofproduct manufacture in accordance with the Consumer Protection Act.
Product MEAT GRINDER The date of manufacture is encoded in the serial number, for example
1st and 2nd characters – week of manufacture; 3rd and 4th characters – year of manufacture;
last 5 characters – serial number.
The product is tested, completed and has no mechanical damage.
The customer agrees with terms of the warranty and service agreement.
Customer signature Seller signature
Model M783
Sserial number
Date of purchase
Information
on the seller company
(name, legal address)
Name and address of the manufacturer (person authorized by the manufacturer), importer and information intended to contact with them is indicated on packaging of the product.
Stamp here

TERMS OF SERVICE
The manufacturer reserves the right to refuse satisfaction of customer demands for warranties in case of non-compliance with operating conditions, terms of installation of the product,
intentional or careless actions of the purchaser (customer) or a third party, which caused damage to the product.
The warranty does not cover:
• elements, characterized by natural wear and tear. Thus, normal wear and tear includes
consequences of product application which caused deterioration of the technical condition
and appearance due to prolonged use of this product.
The warranty does not cover products with the damage caused by:
• improper operation, careless handling, improper storage, improper connection, failure
toobserve supplied operating instructions;
• contact with foreign objects, substances, liquids, insects or animals, which takes place inside
the unit s housing;
• impact of high and low ambient temperatures on heat sensitive parts of the product;
• mechanical effects;
• improper repair and any other intervention, which resulted in changes in the product design;
• application of the product with industrial and/or commercial purposes;
• damage of the power cord;
• application of detergents, not provided in the manual;
• application of non-standard (non-original) consumables, accessories, spare parts;
• connection to mains with a voltage value other than that specified in instructions
foruseofthe product or non-correspondence with state standards of the Russian
Federation;
• force majeure circumstances (fire, flood, lightning).
Replacement of faulty parts of the product (parts, components, assembly units) during
the warranty period shall not lead to establishment of a new warranty period for the entire
product, or a part replaced.
Service centre address
LLC «Premium Service», Moscow, Bolshaya Sadovaya 10.
Current information on availability of service centres in your area can be found on the site
www.bork.ru or using the phone number 8 800 500 88 99.